Product Guide

ManualsBrandsNokia ManualsElectronics7368 ISAM ONT G-140W-H

Table Of Contents

7368 ISAM ONT G-140W-H Product Guide

Nokia — Proprietary and confidential

Use pursuant to applicable agreements

7368 Intelligent Services Access

Manager ONT

7368 ISAM ONT G-140W-H Product Guide

3FE-48054-AAAA-TCZZA

Issue: 01

7368 ISAM ONT G-140W-H Product Guide

Release 06.02.01 | September 2019 | Edition 01

Summary of content (162 pages)

PAGE 1
7368 ISAM ONT G-140W-H Product Guide Release 06.02.
PAGE 2
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Nokia is a registered trademark of Nokia Corporation. Other products and company names mentioned herein may be trademarks or tradenames of their respective owners. The information presented is subject to change without notice. No responsibility is assumed for inaccuracies contained herein. © 2019 Nokia.
PAGE 3
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Preface 1 Preface This preface provides general information about the documentation set for optical network terminals (ONTs). 1.1 Scope This documentation set provides information about safety, features and functionality, ordering, hardware installation and maintenance, and software installation procedures for the current release. 1.
PAGE 4
Release 06.02.01 | September 2019 | Edition 01 Preface 7368 ISAM ONT G-140W-H Product Guide 1.6 Nokia quality processes Nokia’s ONT quality practices are in compliance with TL 9000 requirements. These requirements are documented in the Fixed Networks Quality Manual 3FQ-30146-6000-QRZZA. The quality practices adequately ensure that technical requirements and customer end-point requirements are met.
PAGE 5
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Procedure 2 Preface To access individual documents Individual PDFs of customer documents are also accessible through the Nokia Customer Support website. 1.9 1 Navigate to http://support.alcatel-lucent.com and enter your user name and password. If you are a new user and require access to this service, please contact your Nokia sales representative. 2 From the Technical Content for drop-down menu, choose the product.
PAGE 6
Release 06.02.01 | September 2019 | Edition 01 Preface 7368 ISAM ONT G-140W-H Product Guide 1.9.1 Procedures with options or substeps When there are options in a procedure, they are identified by letters. When there are required substeps in a procedure, they are identified by roman numerals. Procedure 3 Example of options in a procedure At step 1, you can choose option a or b. At step 2, you must do what the step indicates. 1 2 Procedure 4 This step offers two options.
PAGE 7
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 1.10 Preface Multiple PDF document search You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a common term. Adobe Reader displays the results in a single display panel. The results are grouped by PDF file, and you can expand the entry for each file. Note — The PDF files in which you search must be in the same folder.
PAGE 8
Release 06.02.
PAGE 9
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Table of contents 1 Preface.............................................................................................3 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.9.1 1.10 Scope ..........................................................................................................3 Audience......................................................................................................3 Required knowledge..........
PAGE 10
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 10 3.3.1 3.3.2 3.3.3 3.3.4 3.3.5 3.3.6 3.3.7 ONT environmental requirements .............................................................29 Storage ......................................................................................................29 Transportation ...........................................................................................30 Stationary use................................................
PAGE 11
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Issue: 01 5.5 5.6 5.7 5.8 5.9 5.10 5.10.1 5.10.2 5.10.3 5.11 5.11.1 5.11.1.1 5.11.1.2 5.11.1.3 5.11.2 G-140W-H LEDs........................................................................................56 G-140W-H detailed specifications .............................................................57 G-140W-H GEM ports and T-CONTs........................................................
PAGE 12
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 9.2.1 9.3 12 Filename conventions..............................................................................157 ONT configuration file over OMCI ...........................................................
PAGE 13
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide List of figures Issue: 01 2 ETSI ONT safety guidelines .........................................................17 Figure 1 Figure 2 Figure 3 Figure 4 PSE certification ........................................................................................19 Laser product label ....................................................................................22 Laser classification label............................
PAGE 14
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Figure 35 Figure 36 Figure 37 Figure 38 Figure 39 Figure 40 Figure 41 Figure 42 Figure 43 Figure 44 Figure 45 Figure 46 Figure 47 Figure 48 Figure 49 Figure 50 Figure 51 Figure 52 Figure 53 Figure 54 Figure 55 Figure 56 Figure 57 Figure 58 Figure 59 Figure 60 Figure 61 Figure 62 Figure 63 Figure 64 Figure 65 Figure 66 Figure 67 Figure 68 Figure 69 Figure 70 14 Wireless Schedule window.....................................
PAGE 15
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide List of tables 2 ETSI ONT safety guidelines .........................................................17 Table 1 Safety labels ..............................................................................................18 4 ANSI ONT safety guidelines ........................................................33 Table 2 Safety labels ......................................................................................
PAGE 16
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 16 Table 38 Table 39 Table 40 Table 41 Table 42 Table 43 Table 44 Table 45 Table 46 Table 47 Table 48 Table 49 Table 50 Table 51 Table 52 Table 53 Parental control parameters ....................................................................121 DMZ and ALG parameters ......................................................................122 Access control parameters ......................................................
PAGE 17
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide ETSI ONT safety guidelines 2 ETSI ONT safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals (ONTs). 2.1 Safety instructions This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment. 2.1.
PAGE 18
Release 06.02.01 | September 2019 | Edition 01 ETSI ONT safety guidelines 7368 ISAM ONT G-140W-H Product Guide The following is an example of the Caution box. Caution 1 — Possibility of service interruption. Caution 2 — Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. The following is an example of the Note box.
PAGE 19
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Figure 1 ETSI ONT safety guidelines PSE certification This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual. Warning 19841 2.
PAGE 20
Release 06.02.01 | September 2019 | Edition 01 ETSI ONT safety guidelines 2.2.3 7368 ISAM ONT G-140W-H Product Guide Environmental standard compliance The ONT equipment complies with the EN 300 019 European environmental standards. 2.2.4 Laser product standard compliance For most ONTs, the ONT equipment complies with EN 60825-1 and IEC 60825-2 for laser products.
PAGE 21
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 2.3.1 ETSI ONT safety guidelines Power supplies The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property. 2.3.
PAGE 22
Release 06.02.01 | September 2019 | Edition 01 ETSI ONT safety guidelines 7368 ISAM ONT G-140W-H Product Guide Only qualified service personnel who are extremely familiar with laser radiation hazards should install or remove the fiber optic cables and units in this system. Danger — There may be invisible laser radiation at the fiber optic cable when the cable is removed from the connector. Avoid direct exposure to the laser beam. Observe the following danger for laser hazard.
PAGE 23
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Figure 3 ETSI ONT safety guidelines Laser classification label CLASS 1 LASER PRODUCT ' PRODUCTO LASER CLASE 1 ' CLASE 1 DEL LASER LASER CLASSE 1 18992 Figure 4 shows a laser warning label and an explanatory label for laser products. Labels and warning may be provided in other languages.
PAGE 24
Release 06.02.01 | September 2019 | Edition 01 ETSI ONT safety guidelines Figure 4 7368 ISAM ONT G-140W-H Product Guide Laser warning labels INVISIBLE LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Wavelength(s): xxxx nm Normal output power: xx m W Max output power: yyy m W Laser Warning Label Laser Warning Label CLASS 1 LASER PRODUCT RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE EVITER TOUTE EXPOSITION AU FAISCEAU NE PAS DEMONTER.
PAGE 25
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 2.5.4 ETSI ONT safety guidelines Location class Use cable supports and guides to protect the receptacles from strain. 2.6 Environmental requirements See the ONT technical specification documentation for more information about temperature ranges. During operation in the supported temperature range, condensation inside the ONT caused by humidity is not an issue.
PAGE 26
Release 06.02.
PAGE 27
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide ETSI environmental and CRoHS guidelines 3 ETSI environmental and CRoHS guidelines This chapter provides information about the ETSI environmental China Restriction of Hazardous Substances (CRoHS) regulations that govern the installation and operation of the optical line termination (OLT) and optical network termination (ONT) systems. This chapter also includes environmental operation parameters of general interest. 3.
PAGE 28
Release 06.02.01 | September 2019 | Edition 01 ETSI environmental and CRoHS guidelines Figure 5 7368 ISAM ONT G-140W-H Product Guide Products below MCV value label 18986 3.1.2.2 Products containing hazardous substances above Maximum Concentration Value (MCV) label Figure 6 shows the label that indicates a product is above the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products).
PAGE 29
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide ETSI environmental and CRoHS guidelines Together with major international telecommunications equipment companies, Nokia has determined it is appropriate to use an EFUP of 50 years for network infrastructure equipment and an EFUP of 20 years for handsets and accessories.
PAGE 30
Release 06.02.01 | September 2019 | Edition 01 ETSI environmental and CRoHS guidelines 3.3.3 7368 ISAM ONT G-140W-H Product Guide Transportation According to EN 300-019-1-2 - Class 2.3, transportation of the OLT equipment must be in packed, public transportation with no rain on packing allowed. 3.3.4 Stationary use According to EN 300-019-1-3 - Class 3.1/3.2/3.E, stationary use of OLT equipment must be in a temperature-controlled location, with no rain allowed, and with no condensation allowed. 3.3.
PAGE 31
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 3.3.7 ETSI environmental and CRoHS guidelines End-of-life collection and treatment Electronic products bearing or referencing the symbol shown in Figure 7, when put on the market within the European Union (EU), shall be collected and treated at the end of their useful life, in compliance with applicable EU and local legislation. They shall not be disposed of as part of unsorted municipal waste.
PAGE 32
Release 06.02.
PAGE 33
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide ANSI ONT safety guidelines 4 ANSI ONT safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals or units (ONTs or ONUs) in the North American or ANSI market. 4.1 Safety instructions This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment. 4.1.
PAGE 34
Release 06.02.01 | September 2019 | Edition 01 ANSI ONT safety guidelines 7368 ISAM ONT G-140W-H Product Guide The following is an example of the Caution box. Caution 1 — Possibility of service interruption. Caution 2 — Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. The following is an example of the Note box.
PAGE 35
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide ANSI ONT safety guidelines Description Label text Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 36
Release 06.02.01 | September 2019 | Edition 01 ANSI ONT safety guidelines 4.2.
PAGE 37
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 4.2.
PAGE 38
Release 06.02.01 | September 2019 | Edition 01 ANSI ONT safety guidelines 4.2.5 7368 ISAM ONT G-140W-H Product Guide Resistibility requirements compliance The ONT equipment complies with the requirements of ITU Recommendation K.21 for resistibility of telecommunication equipment installed in customer premises to overvoltage and overcurrents. 4.
PAGE 39
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide ANSI ONT safety guidelines Laser product label Figure 10 18455 Figure 11 shows a laser classification label. Laser classification labels may be provided in other languages. Laser classification label Figure 11 CLASS 1 LASER PRODUCT ' PRODUCTO LASER CLASE 1 ' CLASE 1 DEL LASER LASER CLASSE 1 18992 Figure 12 shows a laser warning label and an explanatory label for laser products.
PAGE 40
Release 06.02.01 | September 2019 | Edition 01 ANSI ONT safety guidelines Figure 12 7368 ISAM ONT G-140W-H Product Guide Laser warning labels INVISIBLE LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Wavelength(s): xxxx nm Normal output power: xx m W Max output power: yyy m W Laser Warning Label Laser Warning Label CLASS 1 LASER PRODUCT RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE EVITER TOUTE EXPOSITION AU FAISCEAU NE PAS DEMONTER.
PAGE 41
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Figure 13 ANSI ONT safety guidelines Sample laser product safety label on the ONT equipment Model: MFG: MONTH: XX YEAR: XXXX ICS: XX MRev: XX 3FE55851ABAA MAC:XXXXXXXXXXXX SN:ALCLXXXXXXXX I.T.E FCC ID: XXXXXXXXXXX 12VDC 3A ASSEMBLED IN CHINA 2301 Sugar Bush Rd. Raleigh, NC 27612 CLASS 1 LASER PRODUCT PRODUIT LASER DE CLASSE 1 Intertek 4006119 This device complies with Part 15 of the FCC Rule.
PAGE 42
Release 06.02.01 | September 2019 | Edition 01 ANSI ONT safety guidelines 4.4 7368 ISAM ONT G-140W-H Product Guide Electrical safety guidelines This section provides the electrical safety guidelines for the ONT equipment. Note — The ONTs comply with the U.S. National Electrical Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards. 4.4.
PAGE 43
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide ANSI ONT safety guidelines During installation and maintenance, service personnel must wear wrist straps to prevent damage caused by ESD. Nokia recommends that you prepare the site before you install the ONT equipment. In addition, you must control relative humidity, use static dissipating material for furniture or flooring, and restrict the use of air conditioning. 4.
PAGE 44
Release 06.02.
PAGE 45
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide G-140W-H unit data sheet 5 G-140W-H unit data sheet 5.1 G-140W-H part numbers and identification 5.2 G-140W-H general description 5.3 G-140W-H software and installation feature support 5.4 G-140W-H interfaces and interface capacity 5.5 G-140W-H LEDs 5.6 G-140W-H detailed specifications 5.7 G-140W-H GEM ports and T-CONTs 5.8 G-140W-H performance monitoring statistics 5.9 G-140W-H functional blocks 5.
PAGE 46
Release 06.02.01 | September 2019 | Edition 01 G-140W-H unit data sheet 7368 ISAM ONT G-140W-H Product Guide Ordering kit part number Provisioning number Description CLEI CPR ECI/ Bar code 3FE 48081 AB 3FE 48054 AB GPON indoor ONT with 1 POTS port, 4 10/100/1000 Base-T Ethernet interfaces, Wi-Fi 802.11b/g/n (500 mW), and 802.11ac (1000 mW) networking. Includes two single band 3 dBi multi-directional internal Wi-Fi antennas.
PAGE 47
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Table 4 G-140W-H power supply ONT part numbers Kit: 3FE 48081 AA EMA: 3FE 48054 AA Kit: 3FE 48081 AB EMA: 3FE 48054 AB Kit: 3FE 48081 AC EMA: 3FE 48054 AC Kit: 3FE 48081 BA EMA: 3FE 48054 BA Kit: 3FE 48081 BB EMA: 3FE 48054 BB Kit: 3FE 48081 CA EMA: 3FE 48054 BA 5.
PAGE 48
Release 06.02.01 | September 2019 | Edition 01 G-140W-H unit data sheet 7368 ISAM ONT G-140W-H Product Guide G-140W-H indoor ONTs provide the following functions: • Four RJ-45 10/100/1000 Ethernet ports with auto negotiation and MDI/MDIX auto • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 48 sensing One POTS port for carrier grade voice services Two USB 2.
PAGE 49
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide • • • • • • • • • • 5.2.1 G-140W-H unit data sheet UPnP IGD2.
PAGE 50
Release 06.02.01 | September 2019 | Edition 01 G-140W-H unit data sheet 5.2.1.3 7368 ISAM ONT G-140W-H Product Guide Optical parameters support The ONT supports the reading of optical parameters via TR-069: • • • • • laser bias current voltage temperature received signal levels lower thresholds These are the same optical parameters supported in the GUI. For more information, see Table 22 in the chapter “Configure a G-140W-H indoor ONT”. 5.2.1.
PAGE 51
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide G-140W-H unit data sheet These are the same diagnostic parameters supported in the GUI. For more information, see the Procedure “Diagnose WAN connections” in the chapter “Configure a G-140W-H indoor ONT”. 5.2.2 Independent TR69 session with Saas The prime communication between the Nokia Motive cloud solution and the G-140W-H ONT is TR-069.
PAGE 52
Release 06.02.01 | September 2019 | Edition 01 G-140W-H unit data sheet 5.2.3 7368 ISAM ONT G-140W-H Product Guide TR69 authentication using TLS and CA certificates G-140W-H ONTs support TLS, as well as ACS authentication using SHA-256 pre-installed certificates. If the URL is set to the https://... format, by default, the connection will use TLS without authentication mode. The ONT can also authenticate the ACS using a pre-installed CA certificate. 5.2.
PAGE 53
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 5.2.7 G-140W-H unit data sheet TR-111 support The G-140W-H ONT supports TR-111, which extends the WAN Management Protocol defined in TR-069 to enhance the ability to remotely manage LAN devices. The device-gateway association enables an ACS to identify the associated gateway through which a device is connected.
PAGE 54
Release 06.02.01 | September 2019 | Edition 01 G-140W-H unit data sheet 7368 ISAM ONT G-140W-H Product Guide Note (1) The G-140W-H ONTs provide Wi-Fi service that is enabled and disabled using a Wi-Fi on/off switch. 5.4.1 G-140W-H connections and components Figure 14 shows the physical connections for G-140W-H indoor ONTs. Figure 14 G-140W-H indoor ONT physical connections (back) Figure 15 shows the G-140W-H indoor ONT with a fiber optic connector.
PAGE 55
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Figure 15 G-140W-H unit data sheet G-140W-H indoor ONT with fiber optic connector Table 6 describes the physical connections for G-140W-H indoor ONTs. Table 6 Issue: 01 G-140W-H indoor ONT physical connections Connection (1) Description POTS port This connection is provided through an RJ-11 port. One POTS connection is supported.The POTS port supports voice services.
PAGE 56
Release 06.02.01 | September 2019 | Edition 01 G-140W-H unit data sheet 7368 ISAM ONT G-140W-H Product Guide Note (1) 5.5 The primary path for the earth ground for these ONTs is provided by the 12V Return signal in the power connector. G-140W-H LEDs Figure 16 shows the G-140W-H indoor ONT LEDs. Figure 16 G-140W-H indoor ONT LEDs Table 7 provides LED descriptions for G-140W-H indoor ONTs.
PAGE 57
Release 06.02.
PAGE 58
Release 06.02.01 | September 2019 | Edition 01 G-140W-H unit data sheet Table 8 7368 ISAM ONT G-140W-H Product Guide G-140W-H indoor ONT physical specifications Description Specification Length 6.9 in. (177 mm) Width 1.8 in. (47 mm) Height 6.8 in. (173 mm) Weight [within ± 0.5 lb (0.23 kg)] 0.66 lb (0.3 kg) (net weight of ONT) Table 9 lists the power consumption specifications for G-140W-H indoor ONT.
PAGE 59
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide G-140W-H unit data sheet G-140W-H indoor ONT capacity for GEM ports and T-CONTs Table 11 ONT or MDU Maximum Notes GEM ports per indoor or outdoor ONT 124 124 are present; 122 are available, and 2 are reserved for multicast and debugging T-CONTs per indoor or outdoor ONT 32 32 are present; 31 are available, and 1 is reserved for OMCI Package P ONTs 5.
PAGE 60
Release 06.02.01 | September 2019 | Edition 01 G-140W-H unit data sheet 7368 ISAM ONT G-140W-H Product Guide MCFRAMES DSDRPDFRMS USDRPDFRMS USFRAMES DSFRAMES USBYTES DSBYTES USMCFRAMES DSMCFRAMES G-140W-H (1) ONTL2UNI statistics BYTES ONT Package S ONTs ONTL2UNI performance monitoring statistics FRAMES Table 13 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Note A 5 second polling window limitation exists on the ONT; therefore, the margin of error for each 15 minute window is 5 seconds.
PAGE 61
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide G-140W-H unit data sheet Note (1) 5.9 A 5 second polling window limitation exists on the ONT; therefore, the margin of error for each 15 minute window is 5 seconds. G-140W-H functional blocks G-140W-H indoor ONTs are single-residence ONTs that support Wireless (Wi-Fi) service. Wi-Fi service on these ONTs is compliant with the IEEE 802.11 standard and enabled or disabled using a WLAN button.
PAGE 62
Release 06.02.01 | September 2019 | Edition 01 G-140W-H unit data sheet Figure 18 7368 ISAM ONT G-140W-H Product Guide G-140W-H ONT hardware block POTS ports Control processor SoC DSP SoC Bridge Ethernet MACs GPON MAC Ethernet ports GPON 19421 ONT SoC technology consists of five key elements: • GPON MAC • • • • 62 The Gigabit Passive Optical Network Media Access Control (GPON MAC) element on the SoC terminates the GPON interface using an optical diplexer.
PAGE 63
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide G-140W-H unit data sheet These ONTs can also interact with additional hardware components to support functionality not provided by the SoC technology. 5.10 G-140W-H standards compliance G-140W-H indoor ONTs are compliant with the following standards: • CE marking for European standards for health, safety, and environmental • • • • • • • • • • • • • • • 5.10.1 protection EN 300-328 v1.9.
PAGE 64
Release 06.02.01 | September 2019 | Edition 01 G-140W-H unit data sheet 5.10.2 7368 ISAM ONT G-140W-H Product Guide FCC statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 65
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 5.11.1 G-140W-H unit data sheet Wi-Fi service G-140W-H indoor ONTs feature Wi-Fi service as well as voice and data services. Wi-Fi is a wireless networking technology that uses radio waves to provide wireless HSI and network connections. This ONT complies with the IEEE 802.11 standards, which the Wi-Fi Alliance defines as the basis for Wi-Fi technology. 5.11.1.
PAGE 66
Release 06.02.01 | September 2019 | Edition 01 G-140W-H unit data sheet 7368 ISAM ONT G-140W-H Product Guide Considerations and limitations Some voice features are configurable on a per ONT basis, including Call Waiting, Call Hold, 3-Way Calling, and Call Transfer.
PAGE 67
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Install a G-140W-H indoor ONT 6 Install a G-140W-H indoor ONT 6.1 Purpose 6.2 General 6.3 Prerequisites 6.4 Recommended tools 6.5 Safety information 6.6 Procedure 6.1 Purpose This chapter provides the steps to install a G-140W-H indoor ONT. 6.2 General The steps listed in this chapter describe mounting and cabling for a G-140W-H indoor ONT. 6.
PAGE 68
Release 06.02.01 | September 2019 | Edition 01 Install a G-140W-H indoor ONT 7368 ISAM ONT G-140W-H Product Guide • drill and drill bits • paper clip 6.5 Safety information Read the following safety information before installing the unit. Danger 1 — Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits.
PAGE 69
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 6.6 Install a G-140W-H indoor ONT Procedure Use this procedure to install a G-140W-H indoor ONT. 1 Place the indoor ONT unit on a flat surface, such as a desk or shelf. Note — The G-140W-H cannot be stacked with another ONT or with other equipment. The ONT mounting requirements are: • • • 2 Review the connection locations, as shown in Figure 19.
PAGE 70
Release 06.02.01 | September 2019 | Edition 01 Install a G-140W-H indoor ONT 5 7368 ISAM ONT G-140W-H Product Guide Connect the fiber optic cable with SC/APC adapter to the SC/APC connector on the bottom of the ONT. Danger — Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. Warning — Be careful to maintain a bend radius of no less than 1.5 in. (3.8 cm) when connecting the fiber optic cable.
PAGE 71
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Replace a G-140W-H indoor ONT 7 Replace a G-140W-H indoor ONT 7.1 Purpose 7.2 General 7.3 Prerequisites 7.4 Recommended tools 7.5 Safety information 7.6 Procedure 7.1 Purpose This chapter provides the steps to replace a G-140W-H indoor ONT. 7.2 General The steps listed in this chapter describe mounting and cabling for a G-140W-H indoor ONT. 7.
PAGE 72
Release 06.02.01 | September 2019 | Edition 01 Replace a G-140W-H indoor ONT 7368 ISAM ONT G-140W-H Product Guide • optical power meter • drill and drill bits 7.5 Safety information Read the following safety information before replacing the unit. Danger 1 — Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits.
PAGE 73
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 7.6 Replace a G-140W-H indoor ONT Procedure Use this procedure to replace a G-140W-H indoor ONT. 1 Deactivate the ONT services at the P-OLT. If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). i Use the RTRV-ONT command to verify the ONT status and th associated services. Record the serial number or the SLID of the ONT displayed in the command output.
PAGE 74
Release 06.02.01 | September 2019 | Edition 01 Replace a G-140W-H indoor ONT 7368 ISAM ONT G-140W-H Product Guide 4 Disconnect the POTS, Ethernet, and power cables from the ONT; see Figure 20 for the connector locations on the G-140W-H indoor ONT. 5 Disconnect the fiber optic cables. Danger — Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters.
PAGE 75
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Replace a G-140W-H indoor ONT Note — Fiber cable preparation varies depending on the type and size of the inside or outside plant fiber cable being spliced to the SC/APC fiber optic pigtail cable. 11 Connect the power cable to the power connector. 12 Power up the unit by using the power switch. 13 If used, enable the Wi-Fi service by pressing the WLAN button; see Figure 20 for the location of the WLAN button.
PAGE 76
Release 06.02.
PAGE 77
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Configure a G-140W-H indoor ONT 8 Configure a G-140W-H indoor ONT 8.1 General 8.2 HGU mode GUI configuration 8.3 SFU mode configuration 8.1 General Please refer to the configuration information provided with your OLT for the software configuration procedure for a G-140W-H ONT. For HTTP configuration procedures, please refer to the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide. 8.
PAGE 78
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT 2 7368 ISAM ONT G-140W-H Product Guide Enter your username and password in the Log in window, as shown in Figure 21. The default user name is userAdmin. The default password is a random number, which is included in the ONT kit.
PAGE 79
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 8.2.
PAGE 80
Release 06.02.
PAGE 81
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Procedure 8 LAN status retrieval 1 Figure 23 Configure a G-140W-H indoor ONT Select Status > LAN Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 23. LAN status window Table 18 describes the fields in the LAN status window.
PAGE 82
Release 06.02.
PAGE 83
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Procedure 9 WAN status retrieval 1 Figure 24 Configure a G-140W-H indoor ONT Select Status > WAN Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 24. WAN status window Table 19 describes the fields in the WAN status window. Table 19 WAN status parameters Field Description WAN Connection List Drop-down menu listing all WAN connections.
PAGE 84
Release 06.02.
PAGE 85
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Procedure 10 WAN status IPv6 retrieval 1 Figure 25 Configure a G-140W-H indoor ONT Select Status > WAN Status IPv6 from the top-level menu in the GPON Home Gateway window, as shown in Figure 25. WAN status IPv6 window Table 20 describes the fields in the WAN status IPv6 window. Table 20 WAN status IPv6 parameters Field Description WAN Connection List Drop-down menu listing all WAN connections.
PAGE 86
Release 06.02.
PAGE 87
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Procedure 11 Home networking information retrieval 1 Figure 26 Configure a G-140W-H indoor ONT Select Status > Home Networking from the top-level menu in the GPON Home Gateway window, as shown in Figure 26. Home networking information window Table 21 describes the fields in the Home networking window.
PAGE 88
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT 7368 ISAM ONT G-140W-H Product Guide Field Description Access Point Hexadecimal address of the wireless access point Local Devices Table entry Each entry indicates the status (active or inactive), connection type, device name, IP address, hardware address, IP address allocation, lease remaining, and last active time of each connected local device. (2 of 2) 2 Click Delete to delete a particular local device connection.
PAGE 89
Release 06.02.
PAGE 90
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Procedure 13 Voice information retrieval 1 Figure 28 7368 ISAM ONT G-140W-H Product Guide Select Status > Voice Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 28. Voice Information window Table 23 describes the fields in the Voice Information window. Table 23 Voice Information parameters Field Description Line Choose a line from the drop-down menu. The default is Line 1.
PAGE 91
Release 06.02.
PAGE 92
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Procedure 14 LAN networking configuration 1 Figure 29 7368 ISAM ONT G-140W-H Product Guide Select Network > LAN from the top-level menu in the GPON Home Gateway window, as shown in Figure 29. LAN network window Table 24 describes the fields in the LAN network window.
PAGE 93
Release 06.02.
PAGE 94
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Procedure 15 LAN IPv6 networking configuration 1 Figure 30 7368 ISAM ONT G-140W-H Product Guide Select Network > LAN_IPv6 from the top-level menu in the GPON Home Gateway window, as shown in Figure 30. LAN IPv6 network window Table 25 describes the fields in the LAN IPv6 network window.
PAGE 95
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Configure a G-140W-H indoor ONT Field Description Interface This field appears if you selected the Wan Connection option for the “prefix config” field. Choose a WAN connection interface from the drop-down menu.
PAGE 96
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Procedure 16 WAN networking configuration 1 Figure 31 7368 ISAM ONT G-140W-H Product Guide Select Network > WAN from the top-level menu in the GPON Home Gateway window, as shown in Figure 31. WAN network window Table 26 describes the fields in the WAN network window.
PAGE 97
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Configure a G-140W-H indoor ONT Field Description WAN IP Mode Choose an IP mode from the drop-down menu Manual DNS Manual Domain Name Server (2 of 2) 2 Configure a specific WAN connection. 3 Click Save. 4 STOP. This procedure is complete. Procedure 17 WAN DHCP configuration 1 Figure 32 Select Network > WAN DHCP from the top-level menu in the GPON Home Gateway window, as shown in Figure 32.
PAGE 98
Release 06.02.
PAGE 99
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Procedure 18 WiFi 2.4GHz networking configuration 1 Figure 33 Configure a G-140W-H indoor ONT Select Network > WiFi 2.4GHz from the top-level menu in the GPON Home Gateway window, as shown in Figure 33. WiFi 2.4GHz network window Table 28 describes the fields in the WiFi 2.4GHz network window.
PAGE 100
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Table 28 7368 ISAM ONT G-140W-H Product Guide WiFi 2.
PAGE 101
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Configure a G-140W-H indoor ONT Field Description WPA Key Enter the WPA key Enable WPS Choose Enable or Disable WPS from this drop-down menu WPS Mode Choose a WPS mode from the drop-down menu: PBC (Push Button Connect) or PIN (Personal Identification Number) (2 of 2) Issue: 01 2 Configure the WiFi connection. 3 If you have enabled and configured WPS, click WPS connect. 4 Click Save. 5 STOP.
PAGE 102
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Procedure 19 WiFi 5GHz networking configuration 1 Figure 34 7368 ISAM ONT G-140W-H Product Guide Select Network > WiFi 5GHz from the top-level menu in the GPON Home Gateway window, as shown in Figure 34. WiFi 5GHz network window Table 29 describes the fields in the WiFi 5GHz network window.
PAGE 103
Release 06.02.
PAGE 104
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Procedure 20 Wireless scheduling 1 Figure 35 7368 ISAM ONT G-140W-H Product Guide Select Network > Wireless Schedule from the top-level menu in the GPON Gateway window, as shown in Figure 35. Wireless Schedule window 2 Select the Schedule Function checkbox to turn the wireless signal off for the configured period. 3 Click the plus sign (+) to add a scheduling rule.
PAGE 105
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 8 Click Save Changes. 9 STOP. This procedure is complete. Procedure 21 IP Routing configuration 1 Figure 36 Configure a G-140W-H indoor ONT Select Network > IP Routing from the top-level menu in the GPON Home Gateway window, as shown in Figure 36. IP Routing network window Table 30 describes the fields in the IP Routing network window.
PAGE 106
Release 06.02.
PAGE 107
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Procedure 22 DNS configuration 1 Figure 37 Configure a G-140W-H indoor ONT Select Network > DNS from the top-level menu in the GPON Home Gateway window, as shown in Figure 37. DNS network window Table 31 describes the fields in the DNS network window.
PAGE 108
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT 3 Enter the domain name and IPv4 address and click Add. 4 If required, associate an origin domain with a new domain, click Add. 5 STOP. This procedure is complete. Procedure 23 TR-069 configuration 1 Figure 38 7368 ISAM ONT G-140W-H Product Guide Select Network > TR-069 from the top-level menu in the GPON Home Gateway window, as shown in Figure 38.
PAGE 109
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Configure a G-140W-H indoor ONT Field Description URL URL of the auto-configuration server Username Username used to log in to the auto-configuration server Password Password used to log in to the auto-configuration server Connect Request Username Username used to log in to the ONT Connect Request Password Password used to log in to the ONT (2 of 2) 2 Configure TR-069 by entering the required information.
PAGE 110
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Figure 39 7368 ISAM ONT G-140W-H Product Guide QoS Config window (L2) Figure 40 shows the window for configuring QoS L3 (Layer 3 packet sizes).
PAGE 111
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Figure 40 Configure a G-140W-H indoor ONT QoS Config window (L3) Table 33 describes the fields in the QoS Config window.
PAGE 112
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT 7368 ISAM ONT G-140W-H Product Guide Field Description Type Choose a QoS service layer type from the drop-down menu L2 or L3. Classification Criteria Source MAC Enter the source MAC Select the Exclude checkbox to exclude the source MAC Interface Choose an interface from the drop-down menu Classification Result DSCP Remark Enter the value for the DSCP mark (range: 0-63); valid only for L3 Criteria 802.
PAGE 113
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Configure a G-140W-H indoor ONT • parental control • DMZ and ALG • access control Procedure 25 Firewall configuration 1 Select Security > Firewall from the top-level menu in the GPON Home Gateway window, as shown in Figure 41. Figure 41 Firewall window Three security levels are available: High, Low, and Off.
PAGE 114
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT 7368 ISAM ONT G-140W-H Product Guide 3 Click Save. 4 STOP. This procedure is complete. Procedure 26 MAC filter configuration 1 Select Security > Mac Filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 42. Figure 42 MAC filter window Table 35 describes the fields in the MAC filter window.
PAGE 115
Release 06.02.
PAGE 116
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Procedure 27 7368 ISAM ONT G-140W-H Product Guide IP filter configuration 1 Select Security > IP filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 43. Figure 43 IP filter window Table 36 describes the fields in the IP filter window.
PAGE 117
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Configure a G-140W-H indoor ONT 3 Click Add. 4 STOP. This procedure is complete. Procedure 28 URL filter configuration 1 Select Security > URL Filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 44. URL Filter window Figure 44 Note — You cannot use URL filtering for HTTPS. The URL is encrypted when using HTTPS. Table 37 describes the fields in the URL Filter window.
PAGE 118
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT 7368 ISAM ONT G-140W-H Product Guide Field Description URL Address Type the URL address Port - default to 80 Type the port number; the default is 80 (2 of 2) 118 2 Configure the URL Filter. 3 Click Add Filter. 4 STOP. This procedure is complete.
PAGE 119
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Procedure 29 Parental control 1 Issue: 01 Configure a G-140W-H indoor ONT Select Security > Parent Control from the top-level menu in the GPON Gateway window, as shown in Figure 45.
PAGE 120
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Figure 45 7368 ISAM ONT G-140W-H Product Guide Parental Control window Table 38 describes the fields in the Parental Control window.
PAGE 121
Release 06.02.
PAGE 122
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Procedure 30 7368 ISAM ONT G-140W-H Product Guide DMZ and ALG configuration 1 Select Security > DMZ and ALG from the top-level menu in the GPON Home Gateway window, as shown in Figure 46. Figure 46 DMZ and ALG window Table 39 describes the fields in the DMZ and ALG window.
PAGE 123
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Configure a G-140W-H indoor ONT 5 Click Save DMZ. 6 STOP. This procedure is complete. Procedure 31 Access control configuration This procedure describes how to configure the access control level (ACL). Note 1 — ACL takes precedence over the firewall policy. Note 2 — The trusted network object will be shared for all WAN connections; it is not applied individually to a WAN connection.
PAGE 124
Release 06.02.
PAGE 125
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Configure a G-140W-H indoor ONT • USB • UPnP and DLNA Procedure 32 Port forwarding configuration 1 Figure 48 Select Application > Port forwarding from the top-level menu in the GPON Home Gateway window, as shown in Figure 48. Port forwarding window Table 41 describes the fields in the port forwarding window.
PAGE 126
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT 7368 ISAM ONT G-140W-H Product Guide Field Description WAN Connection List Choose a WAN connection from the drop-down menu Note: only active devices are shown on this menu (2 of 2) 2 Configure port forwarding. 3 Click Add. 4 STOP. This procedure is complete. Procedure 33 Port triggering 1 Figure 49 Select Application > Port Triggering from the top-level menu in the GPON Gateway window, as shown in Figure 49.
PAGE 127
Release 06.02.
PAGE 128
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Procedure 34 DDNS configuration 1 Figure 50 7368 ISAM ONT G-140W-H Product Guide Select Application > DDNS from the top-level menu in the GPON Home Gateway window, as shown in Figure 50. DDNS window Table 43 describes the fields in the DDNS window.
PAGE 129
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Procedure 35 NTP configuration 1 Figure 51 Configure a G-140W-H indoor ONT Select Application > NTP from the top-level menu in the GPON Home Gateway window, as shown in Figure 51. NTP window Table 44 describes the fields in the NTP window.
PAGE 130
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT 7368 ISAM ONT G-140W-H Product Guide 3 Click Save. 4 STOP. This procedure is complete. Procedure 36 USB configuration You can connect USB storage devices and USB printers to the USB ports of the device. The USB menu enables you to configure FTP and SFTP for your USB storage devices. The USB connected devices are shown in overview table on the bottom of the USB window.
PAGE 131
Release 06.02.
PAGE 132
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Procedure 37 UPnP and DLNA configuration 1 Figure 53 7368 ISAM ONT G-140W-H Product Guide Select Application > UPnP and DLNA from the top-level menu in the GPON Home Gateway window, as shown in Figure 53. UPnP and DLNA window 2 Select the Enable UPnP/DLNA checkbox to enable UPnP/DLNA. 3 Click Save/Apply. 4 STOP. This procedure is complete. 8.2.
PAGE 133
Release 06.02.
PAGE 134
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT • • 1 Figure 54 7368 ISAM ONT G-140W-H Product Guide the first character cannot be a special character there are not enough character classes Select Maintain > Password from the top-level menu in the GPON Home Gateway window, as shown in Figure 54. Password window Table 46 describes the fields in the password window.
PAGE 135
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 3 Click Save. 4 STOP. This procedure is complete. Procedure 39 WAN speed test 1 Figure 55 Configure a G-140W-H indoor ONT Select Maintain > Speed Test from the top-level menu in the GPON Home Gateway window, as shown in Figure 55. Speed Test window 2 Click Start to start the speed test. Enter the URL for the test server in the pop-up window. 3 Issue: 01 STOP. This procedure is complete.
PAGE 136
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Procedure 40 LOID configuration 1 Figure 56 7368 ISAM ONT G-140W-H Product Guide Select Maintain > LOID Config from the top-level menu in the GPON Home Gateway window, as shown in Figure 56. LOID Config window Table 47 describes the fields in the LOID configuration window.
PAGE 137
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Procedure 41 SLID configuration 1 Figure 57 Configure a G-140W-H indoor ONT Select Maintain > SLID Configuration from the top-level menu in the GPON Home Gateway window, as shown in Figure 57. SLID configuration window Table 48 describes the fields in the SLID configuration window.
PAGE 138
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT 3 Click Save. 4 STOP. This procedure is complete. Procedure 42 Device management 1 Figure 58 7368 ISAM ONT G-140W-H Product Guide Select Maintain > Device Management from the top-level menu in the GPON Home Gateway window, as shown in Figure 58. Device management window Table 49 describes the fields in the Device management window.
PAGE 139
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 3 Click Add. 4 STOP. This procedure is complete. Procedure 43 Backup and restore 1 Figure 59 Issue: 01 Configure a G-140W-H indoor ONT Select Maintain > Backup and Restore from the top-level menu in the GPON Home Gateway window, as shown in Figure 59. Backup and Restore window 2 Click Choose file and choose the backup file.
PAGE 140
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Procedure 44 Upgrade firmware 1 Figure 60 140 7368 ISAM ONT G-140W-H Product Guide Select Maintain > Firmware Upgrade from the top-level menu in the GPON Home Gateway window, as shown in Figure 60. Firmware upgrade window 2 Click Choose file and choose the firmware file. 3 Click Upgrade to upgrade the firmware. 4 STOP. This procedure is complete.
PAGE 141
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Procedure 45 Reboot ONT 1 Figure 61 Issue: 01 Configure a G-140W-H indoor ONT Select Maintain > Reboot Device from the top-level menu in the GPON Home Gateway window, as shown in Figure 61. Reboot window 2 Click Reboot to reboot the ONT. 3 STOP. This procedure is complete.
PAGE 142
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Procedure 46 Restore factory defaults 1 Figure 62 142 7368 ISAM ONT G-140W-H Product Guide Select Maintain > Factory Default from the top-level menu in the GPON Home Gateway window, as shown in Figure 62. Factory default window 2 Click Factory Default to reset the ONT to its factory default settings. 3 STOP. This procedure is complete.
PAGE 143
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Procedure 47 Diagnose WAN connections 1 Figure 63 Issue: 01 Configure a G-140W-H indoor ONT Select Maintain > Diagnostics from the top-level menu in the GPON Home Gateway window, as shown in Figure 63. Diagnostics window 2 Choose a WAN connection to diagnose from the drop-down menu. 3 Enter the IP address or domain name. 4 Select the test type: ping, traceroute, or both.
PAGE 144
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT 9 Click Cancel to cancel the test. 10 STOP. This procedure is complete. Procedure 48 View log files 1 Figure 64 144 7368 ISAM ONT G-140W-H Product Guide Select Maintain > Log from the top-level menu in the GPON Home Gateway window, as shown in Figure 64.
PAGE 145
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 2 Choose a write level from the drop-down menu to determine which types of events are recorded in the log file: • • • • • • • • 3 Emergency Alert Critical Error Warning Notice Informational Debug Choose a reading level from the drop-down menu to determine which types of events to display from the log file: • • • • • • • • 8.2.
PAGE 146
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Procedure 49 7368 ISAM ONT G-140W-H Product Guide Retrieve Residential Gateway (RG) troubleshooting counters 1 Select RG Troubleshooting Counters from the left menu in the GPON Home Gateway window. The RG Troubleshooting Counters window appears; see Figure 65. Figure 65 RG Troubleshooting Counters window Table 50 describes the fields in the RG Troubleshooting Counters window.
PAGE 147
Release 06.02.
PAGE 148
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT 7368 ISAM ONT G-140W-H Product Guide 3 Reboot the ONT. 4 STOP. This procedure is complete. Procedure 51 Modifying the operator ID 1 Register the ONT with the OLT. 2 Using an XML editor, create a file called OntConfig.xml with the following content:
PAGE 149
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Configure a G-140W-H indoor ONT To enable auto download again, use the DEL-ONTSWCTRL command. See the TL1 Commands and Messages Guide for the 7342 or 7360 for more information about the DEL-ONTSWCTRL command. 8 8.3.2 STOP. This procedure is complete. Login Use the procedure below to login to the web-based GUI for the G-140W-H.
PAGE 150
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT 7368 ISAM ONT G-140W-H Product Guide 3 Click Login. 4 STOP. This procedure is complete. 8.3.3 Device and connection status The G-140W-H ONT supports the retrieval of device information. Procedure 53 Device information retrieval 1 Figure 67 Select Status > Device Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 67.
PAGE 151
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide Configure a G-140W-H indoor ONT Field Description Hardware Version Hardware version of the ONT Boot Version Boot version of the ONT Software Version Software version of the ONT Chipset Chipset of the ONT Device Running Time Amount of time the device has run since last reset in hours, minutes, and seconds (2 of 2) 2 Click Refresh to update the displayed information. 3 STOP. This procedure is complete. 8.3.
PAGE 152
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT Table 52 Field Description Original Password Current password New Password New password Re-enter Password Password must match the new password entered above Prompt Message Password prompt message Configure the new password. 3 Click Save. 4 STOP. This procedure is complete.
PAGE 153
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide 4 Click Save/Apply. 5 STOP. This procedure is complete. Procedure 56 SLID configuration 1 Figure 70 Configure a G-140W-H indoor ONT Select Maintain > SLID Configuration from the top-level menu in the GPON Home Gateway window, as shown in Figure 70. SLID configuration window Table 53 describes the fields in the SLID configuration window.
PAGE 154
Release 06.02.01 | September 2019 | Edition 01 Configure a G-140W-H indoor ONT 154 7368 ISAM ONT G-140W-H Product Guide 3 Click Save. 4 STOP. This procedure is complete.
PAGE 155
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide ONT configuration file over OMCI 9 ONT configuration file over OMCI 9.1 Purpose 9.2 Supported configuration file types 9.3 ONT configuration file over OMCI 9.1 Purpose This procedure describes how to use configuration files over OMCI to configure ONTs.
PAGE 156
Release 06.02.01 | September 2019 | Edition 01 ONT configuration file over OMCI Table 54 7368 ISAM ONT G-140W-H Product Guide Supported configuration files File Index Description Details Supported ONTs/DPU PRE ONT pre-configuration file The XML-based PRECONFIG file controls the working mechanics of the ONT for various services. The default behavior of different ONTs may vary based on the factory settings.
PAGE 157
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide ONT configuration file over OMCI File Index Description Details Supported ONTs/DPU GFT G.fast-related configuration file This text-based json script file controls the default behavior of the G.Fast ONT. HGU ONTs: This file includes the provisioning parameters of the G.fast transports layer; it does not include VLAN or QoS provisioning.
PAGE 158
Release 06.02.01 | September 2019 | Edition 01 ONT configuration file over OMCI Procedure 57 7368 ISAM ONT G-140W-H Product Guide Configuring an ONT using a configuration file via OMCI 1 Generate the TAR file to be uploaded to the OLT. Using the raw configuration file(s) provided by Nokia, generate the TAR file as follows: i On a Linux platform, rename the raw configuration file to adhere to the naming convention, as described in section 9.2.
PAGE 159
Release 06.02.01 | September 2019 | Edition 01 7368 ISAM ONT G-140W-H Product Guide ONT configuration file over OMCI FILENAME2 will be downloaded and FILENAME2 will be made passive. An ONT reboot is not required. iv If pland-cfgfileX=FILENAME3 and dnload-cfgfileX= FILENAME 4, the OLT reports an error because the filenames are not the same.
PAGE 160
Release 06.02.
PAGE 161
Release 06.02.