Nokia Bluetooth Headset BH-106 2 3 1 6 4 5 8 7 9 Copyright © 2009 Nokia. All rights reserved.
DECLARATION OF CONFORMITY Hereby, NOKIA CORPORATION declares that this BH-106 product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/ EC. A copy of the Declaration of Conformity can be found at http://www.nokia.com/phones/ declaration_of_conformity/. © 2009 Nokia. All rights reserved. Nokia, Nokia Connecting People and the Nokia Original Accessories logo are trademarks or registered trademarks of Nokia Corporation.
Export Controls This device may contain commodities, technology or software subject to export laws and regulations from the US and other countries. Diversion contrary to law is prohibited. Introduction With the Nokia Bluetooth Headset BH-106, you can make and receive calls while on the move. Read this user guide carefully before using the headset. Also, read the user guide for the mobile device that you connect to the headset. This product may contain small parts.
Get started The headset contains the following parts shown on the title page: earpiece (1), microphone (2), answer/end key (3), charger connector (4), plug for fixing the earpiece cable (5), power key (6), and indicator light (7). Before using the headset, you must charge the battery and pair the headset with a compatible device. Parts of the device are magnetic. Metallic materials may be attracted to the device.
during charging. Charging the battery fully may take up to 2 hours. 3. When the battery is fully charged, the green indicator light is displayed. Disconnect the charger from the headset, then from the wall outlet. The fully charged battery has power for up to 5 hours and 30 minutes of talk time or up to 120 hours of standby time. To check the battery charge when the headset is not connected to a charger, press the power key. If the indicator light is green, the charge level is sufficient.
indicator light starts to flash quickly. 3. Within about 3 minutes, activate Bluetooth connectivity on your device, and set it to search for Bluetooth devices. 4. Select the headset from the list of found devices. 5. If necessary, enter the passcode 0000 to pair and connect the headset to your device. In some devices, you may need to make the connection separately after pairing. When the headset is connected to your device and is ready for use, the green indicator light flashes about every 5 seconds.
progress, press the answer/end key twice. To activate voice dialling (if your device supports this feature with the headset), when no call is in progress, press and hold the answer/ end key for about 2 seconds. Proceed as described in the user guide of your device. To answer or end a call, press the answer/end key. To reject a call, press this key twice. To switch a call from the headset to a compatible device, press and hold the answer/end key for about 2 seconds, or switch off the headset.
Troubleshooting If you cannot connect the headset to your compatible device, check that the headset is charged, switched on, and paired with your device. Battery and charger information This device has an internal, nonremovable, rechargeable battery. Do not attempt to remove the battery from the device as you may damage the device. This device is intended for use when supplied with power from the following chargers: AC-3, AC-4, AC-5, AC-8, and DC-4.
Always try to keep the battery between 15°C and 25°C (59°F and 77°F). Extreme temperatures reduce the capacity and lifetime of the battery. A device with a hot or cold battery may not work temporarily. Battery performance is particularly limited in temperatures well below freezing. Do not dispose of batteries in a fire as they may explode. Batteries may also explode if damaged. Never use any charger that is damaged.
Care and maintenance Your device is a product of superior design and craftsmanship and should be treated with care. The following suggestions will help you protect your warranty coverage. • Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, allow it to dry completely. • Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged.