Nokia FastMile 4G Receiver Product Overview FastMile 2.
Nokia FastMile 4G Receiver Product Overview Nokia is a registered trademark of Nokia Corporation. Other products and company names mentioned herein may be trademarks or tradenames of their respective owners. The information presented is subject to change without notice. No responsibility is assumed for inaccuracies contained herein. © 2019 Nokia.
Nokia FastMile 4G Receiver Product Overview Preface 1 Preface This preface provides general information about the Product Overview for the Nokia FastMile 4G Receiver. 1.1 Scope This document provides an overview of the Nokia FastMile 4G Receiver along with information about safety and troubleshooting the Nokia FastMile 4G Receiver. 1.
Preface Nokia FastMile 4G Receiver Product Overview 1.6 Nokia quality processes Nokia’s FastMile 4G Receiver quality practices are in compliance with TL 9000 requirements.These requirements are documented in the Fixed Networks Quality Manual 3FQ-30146-6000-QRZZA. The quality practices adequately ensure that technical requirements and customer end-point requirements are met.
Nokia FastMile 4G Receiver Product Overview Preface Danger — Danger indicates that the described activity or situation may result in serious personal injury or death; for example, high voltage or electric shock hazards. Warning — Warning indicates that the described activity or situation may, or will, cause equipment damage or serious performance problems. Caution — Caution indicates that the described activity or situation may, or will, cause service interruption.
Preface Nokia FastMile 4G Receiver Product Overview 2 Procedure 3 You must perform this step. Example of required substeps in a step At step 1, you must perform a series of substeps within the step. 1 This step has a series of substeps that you must perform to complete the step. You must perform the following substeps: i This is the first substep. iiThis is the second substep. iii 2 This is the third substep. You must perform this step. 1.
Nokia FastMile 4G Receiver Product Overview 6 Issue: 01 DRAFT Preface Click on the Search button. Acrobat Reader displays the search results. You can expand the entries for each document by clicking on the + symbol.
Preface 8 Nokia FastMile 4G Receiver Product Overview 3TG-00386-ABAA-TCZZA DRAFT Issue: 01 DRAFT
Nokia FastMile 4G Receiver Product Overview ETSI environmental and CRoHS guidelines 2 ETSI environmental and CRoHS guidelines This chapter provides information about the ETSI environmental China Restriction of Hazardous Substances (CRoHS) regulations that govern the installation and operation of Nokia FastMile 4G Receiver equipment. This chapter also includes environmental operation parameters of general interest. 2.
ETSI environmental and CRoHS guidelines Figure 1 Nokia FastMile 4G Receiver Product Overview Products below MCV value label 18986 2.1.2.2 Products containing hazardous substances above Maximum Concentration Value (MCV) label Figure 2 shows the label that indicates a product is above the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products).
Nokia FastMile 4G Receiver Product Overview ETSI environmental and CRoHS guidelines 18985 Together with major international telecommunications equipment companies, Nokia has determined it is appropriate to use an EFUP of 50 years for network infrastructure equipment and an EFUP of 20 years for handsets and accessories.
ETSI environmental and CRoHS guidelines 2.3.2 Nokia FastMile 4G Receiver Product Overview Storage According to ETS 300-019-1-1 - Class 1.1, storage of Nokia FastMile 4G Receiver equipment must be in Class 1.1, weather-protected, temperature-controlled locations. 2.3.3 Transportation According to EN 300-019-1-2 - Class 2.3, transportation of Nokia FastMile 4G Receiver equipment must be in packed, public transportation. 2.3.4 Stationary use According to EN 300-019-1-3 - Class 3.1/3.2/3.
Nokia FastMile 4G Receiver Product Overview ETSI environmental and CRoHS guidelines Nokia has implemented a material/substance content management process. The process is described in: Nokia process for ensuring RoHS Compliance (1AA002660031ASZZA). This ensures compliance with the European Union Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS2).
ETSI environmental and CRoHS guidelines Nokia FastMile 4G Receiver Product Overview 2.4 Additional information See chapter 17 for RF exposure information.
Nokia FastMile 4G Receiver Product Overview ETSI safety guidelines 3 ETSI safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of Nokia FastMile 4G Receiver equipment in the ETSI market. 3.1 Safety instructions This section describes the safety instructions that are provided in the customer documentation and on the Nokia FastMile 4G Receiver equipment. 3.1.
ETSI safety guidelines Nokia FastMile 4G Receiver Product Overview Do not proceed beyond a warning until the indicated conditions are fully understood and met. The following is an example of the Caution box. Caution 1 — Possibility of service interruption. Caution 2 — Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met.
Nokia FastMile 4G Receiver Product Overview 3.2.
ETSI safety guidelines Nokia FastMile 4G Receiver Product Overview 3.3 Electrical safety guidelines This section provides the electrical safety guidelines for the Nokia FastMile 4G Receiver equipment. Note 1 — The Nokia FastMile 4G Receiver equipment complies with the U.S. National Electrical Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards. Note 2 — The Nokia FastMile 4G Receiver equipment complies with BS EN 61140. 3.3.
Nokia FastMile 4G Receiver Product Overview 3.4 ETSI safety guidelines ESD safety guidelines The Nokia FastMile 4G Receiver equipment is sensitive to ESD if opened. Operations personnel must observe the following ESD instructions when they handle the Nokia FastMile 4G Receiver equipment. Caution — This equipment is ESD sensitive if opened. Proper ESD protections should be used if you open the Nokia FastMile 4G Receiver.
ANSI safety guidelines Nokia FastMile 4G Receiver Product Overview 4 ANSI safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the Nokia FastMile 4G Receiver equipment in the North American or ANSI market. 4.1 Safety instructions This section describes the safety instructions that are provided in the customer documentation and on the Nokia FastMile 4G Receiver equipment. 4.1.
Nokia FastMile 4G Receiver Product Overview ANSI safety guidelines Do not proceed beyond a warning until the indicated conditions are fully understood and met. The following is an example of the Caution box. Caution 1 — Possibility of service interruption. Caution 2 — Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met.
ANSI safety guidelines Nokia FastMile 4G Receiver Product Overview CE marking There are various CE symbols for CE compliance. Figure 4 shows a sample safety label for FCC and Figure 5 shows a sample safety label for ETL. Figure 4 Sample safety label for FCC Tested to Comply with FCC Standards FOR HOME OR OFFICE USE ® COMMUNICATION SERVICE EQUIPMENT cUS LISTED 27FY Type 3R Enclosure - Rainproof This device complies with Part 15 of the FCC Rules.
Nokia FastMile 4G Receiver Product Overview 4.2.1 ANSI safety guidelines EMC, EMI, and ESD compliance The Nokia FastMile 4G Receiver equipment complies with the following EMC, EMI, and ESD requirements: • Federal Communications Commission PART 15-RADIO FREQUENCY DEVICES Subpart C-INTENTIONAL RADIATORS Title 47 CFR Part 15. Part 15.247, Part 15.255 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
ANSI safety guidelines Nokia FastMile 4G Receiver Product Overview Note — The Nokia FastMile 4G Receiver equipment complies with the U.S. National Electrical Code. However, local electrical authorities have jurisdiction when there are differences between the local and U.S. standards. 4.3.1 Power supplies The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia.
Nokia FastMile 4G Receiver Product Overview ANSI safety guidelines Service personnel are not required to wear wrist straps when performing normal installation or maintenance activities. 4.5 Environmental requirements See chapter 16 in this document for information about temperature ranges for the Nokia FastMile 4G Receiver equipment and other Nokia FastMile 4G Receiver specifications.
Nokia FastMile 4G Receiver Product Overview Table of contents 1 Preface............................................................................................................... 3 1.1 Scope................................................................................................................................ 3 1.2 Audience ........................................................................................................................... 3 1.3 Required knowledge ........................
Nokia FastMile 4G Receiver Product Overview 4 ANSI safety guidelines ................................................................................... 20 4.1 Safety instructions .......................................................................................................... 20 4.1.1 Safety instruction boxes in customer documentation .................................................. 20 4.1.2 Safety-related labels ..................................................................................
Nokia FastMile 4G Receiver Product Overview 13.2 Using the Nokia Wireless app to manage a unit managed by the Nokia Altiplano FastMile Controller ............................................................................................................... 62 13.3 Using the Nokia Wireless app to manage a unit managed by an ACS ........................ 81 14 Management using the Web UI .................................................................... 95 14.
Nokia FastMile 4G Receiver Product Overview List of figures 2 ETSI environmental and CRoHS guidelines.................................9 Figure 1 Figure 2 Figure 3 Products below MCV value label...............................................................10 Products above MCV value label ..............................................................11 Recycling/take back/disposal of product symbol.......................................13 4 ANSI safety guidelines.......................................
Nokia FastMile 4G Receiver Product Overview Figure 23 Figure 24 Figure 25 Figure 26 Figure 27 Figure 28 Figure 29 Figure 30 Figure 31 Figure 32 Figure 33 Figure 34 Figure 35 Figure 36 Figure 37 Figure 38 Figure 39 Figure 40 Figure 41 Figure 42 Figure 43 Figure 44 Figure 45 Figure 46 Figure 47 Figure 48 14 30 Screen showing the Already Installed option for unit managed by the Nokia Altiplano FastMile Controller through NETCONF......................
Nokia FastMile 4G Receiver Product Overview Figure 49 Figure 50 Figure 51 Figure 52 Figure 53 Figure 54 Figure 55 Figure 56 Figure 57 Figure 58 Figure 59 Figure 60 Figure 61 Figure 62 Figure 63 Figure 64 Figure 65 Issue: 01 DRAFT Example of the Status screen when the FastMile 4G Receiver is not connected to a cell.............................................................................102 Example of the Status screen when the FastMile 4G Receiver is connected to a cell................................
Nokia FastMile 4G Receiver Product Overview 32 3TG-00386-ABAA-TCZZA DRAFT Issue: 01 DRAFT
Nokia FastMile 4G Receiver Product Overview List of tables 3 ETSI safety guidelines..................................................................15 Table 1 Safety labels..............................................................................................16 4 ANSI safety guidelines.................................................................21 Table 2 Safety labels..............................................................................................
Nokia FastMile 4G Receiver Product Overview Product overview 5 Product overview 5.1 Overview of the Nokia FastMile 4G Receiver 5.2 End-to-end example 5.1 Overview of the Nokia FastMile 4G Receiver The Nokia FastMile 4G Receiver is an outdoor device used in the Nokia FastMile 4G solution.
Nokia FastMile 4G Receiver Product Overview Figure 6 Application example of the Nokia FastMile 4G Receiver Nokia PoE FastMile 4G Receiver Injector Radio basestation Residential gateway WiFi or Ethernet connectivity to end-user devices LTE 1 Gbps Ethernet Wi-Fi or Ethernet 28814 The Nokia FastMile 4G Receiver is available in the following model types: • • • • • • • • • Compact multi-band; this model type has the following features: fixed beamforming antennas multi-band transmission Compact mono-b
Nokia FastMile 4G Receiver Product Overview Product overview Figure 7 Examples of model types of the Nokia FastMile 4G Receiver Compact/multi-band Compact/mono-band ABA 28770 The Nokia FastMile 4G Receiver has built-in antenna and LTE modem that provide the LTE broadband access to the network. The Nokia FastMile 4G Receiver is capable of withstanding outdoor environmental conditions. It has an IP rating of IP66 TYPE3.
Nokia FastMile 4G Receiver Product Overview Due to the independence between the Nokia FastMile 4G Receiver and the gateway, the Nokia FastMile 4G Receiver also addresses the business market. The business customer can seamlessly re-use their existing business gateway. The Nokia FastMile 4G Receiver supports extended QCI and multiple APNs that can be mapped on VLANs to support QoS for different services.
Functional overview Nokia FastMile 4G Receiver Product Overview 6 Functional overview 6.1 Overview 6.2 LTE characteristics 6.3 Data forwarding 6.4 Ethernet characteristics 6.5 Power supply characteristics 6.6 Remote management protocols 6.1 Overview The Nokia FastMile 4G Receiver provides wireless broadband access in the form of LTE to meet the ever growing network needs of end users.
Nokia FastMile 4G Receiver Product Overview Functional overview See the Installation guide for more information about how the Nokia Wireless app is used in the installation process. See chapter 13 in this document for more information about how Nokia Wireless app can be used for management of the Nokia FastMile 4G Receiver. 6.1.
Functional overview Nokia FastMile 4G Receiver Product Overview • LTE 3GPP Release 12 Compliant, UE Category 12 • supports the E-UTRA bands listed in Table 3 Table 3 E-UTRA bands supported by the Nokia FastMile 4G Receiver E-UTRA bands Model Band 42/43/48 (mono-band support) 4G01-A Band 42/43/48 (ABA support) 4G01-B Band 3 (mono-band support) 4G02-A Band 7/38/40/41 (mono-band support) 4G03-A Band B3/B7/B20/B32 (multi-band support) 4G04-A Band B1/B3/B7/B38/B40/B41/B20/B28 (multi-band support)
Nokia FastMile 4G Receiver Product Overview Functional overview connection of a customer-supplied Cat5e shielded twisted pair Ethernet cable with standard pinouts that is up to a maximum of 80 m (262 ft) in length • supports IEEE802.3 1000BASE-T • supports IEEE802.3az energy efficient Ethernet • the Ethernet cable for all models is also used for power over Ethernet (PoE) as per IEEE802.3 at type-2 6.
Functional overview Nokia FastMile 4G Receiver Product Overview Figure 9 Remote management of the Nokia FastMile 4G Receiver through the Nokia Altiplano FastMile Controller IPTV Core Internet VoIP Radio basestation Nokia PoE FastMile 4G Receiver Injector Residential gateway Nokia Altiplano NETCONF Fastmile Controller ACS WiFi or Etherne connectivity to end-user devic that are using IPTV, internet, and VoIp TR-069 LTE 1 Gbps Ethernet Wi-Fi or Ethernet 28 Figure 10 shows an ACS being used for re
Nokia FastMile 4G Receiver Product Overview Figure 10 Functional overview Remote management of the Nokia FastMile 4G Receiver through an ACS IPTV Core Internet Radio basestation VoIP ACS Nokia PoE FastMile 4G Receiver Injector Residential gateway TR-069 LTE 1 Gbps Ethernet WiFi or Ethernet connectivity to end-user devices that are using IPTV, internet, and VoIp Wi-Fi or Ethernet 28817 Issue: 01 DRAFT 3TG-00386-ABAA-TCZZA DRAFT 43
Nokia FastMile 4G Receiver Product Overview Model overview 7 Model overview 7.1 Models of the Nokia FastMile 4G Receiver 7.1 Models of the Nokia FastMile 4G Receiver A wide range of models are available for the Nokia FastMile 4G Receiver to support different E-UTRA bands and band combinations for LTE. All models can be wall-mounted or pole-mounted.
Nokia FastMile 4G Receiver Product Overview Model overview Model E-UTRA band support and frequencies Antenna configuration Model type 4G05-A • Bands 7, 38, 40, and 41 are integrated with > 11 dBi fixed beamforming antenna Compact multiband Band 1: FDD, Tx 1920 MHz –1980 MHz, Rx 2110 MHz –2170 MHz • Band 3: FDD, Tx 1710 MHz –1785 MHz, Rx 1805 MHz – 1880 MHz • Band 7: FDD, Tx 2500 MHz – 2570 MHz, Rx 2620 MHz – 2690 MHz • Bands 1 and 3 are integrated with > 9 dBi fixed beamforming antenna Bands 20
Nokia FastMile 4G Receiver Product Overview 8.2 Physical interfaces of the Compact multi-band models 8.1 Physical interfaces of the Compact monoband and ABA models Table 7 describes the physical interfaces of the Compact mono-band and ABA models of the Nokia FastMile 4G Receiver.
Nokia FastMile 4G Receiver Product Overview Figure 11 Location of physical interfaces on the Compact mono-band and ABA models of the Nokia FastMile 4G Receiver SIM slot Status LED Ground point Reset button Ethernet Cable 28797 8.2 Physical interfaces of the Compact multiband models Table 8 describes the physical interfaces of Compact multi-band models of the Nokia FastMile 4G Receiver.
Nokia FastMile 4G Receiver Product Overview Interface Description Reset button Button to reset the Nokia FastMile 4G Receiver. Located on the underside of the unit; see Figure 13. SIM slot Slot for Nano/4FF SIM card for a Compact multi-band model of the Nokia FastMile 4G Receiver. Located on the underside of the unit; see Figure 13. See section 9.2 for SIM card information for the Compact multi-band models of the Nokia FastMile 4G Receiver.
Nokia FastMile 4G Receiver Product Overview Figure 13 Location of physical interfaces on the underside of the Compact multi-band models of the Nokia FastMile 4G Receiver Vent M6 Ethernet port SIM slot Reset button 28771 Issue: 01 DRAFT 3TG-00386-ABAA-TCZZA DRAFT 49
Nokia FastMile 4G Receiver Product Overview SIM cards 9 SIM cards 9.1 SIM card information for the Compact mono-band and ABA models 9.2 SIM card information for the Compact multi-band models 9.1 SIM card information for the Compact monoband and ABA models The SIM card installed in the Nokia FastMile 4G Receiver allows the Nokia FastMile 4G Receiver to connect to the LTE network and determines the remote management protocol supported for the Nokia FastMile 4G Receiver; see section 6.
Nokia FastMile 4G Receiver Product Overview SIM cards 9.2 SIM card information for the Compact multiband models The SIM card installed in the Nokia FastMile 4G Receiver allows the Nokia FastMile 4G Receiver to connect to the LTE network and determines the remote management protocol supported for the Nokia FastMile 4G Receiver; see section 6.6 for more information about remote management. Figure 15 shows a detailed view of the SIM card slot on the Compact multi-band models of the Nokia FastMile 4G Receiver.
Nokia FastMile 4G Receiver Product Overview 10.2 Signal strength LEDs 10.
Nokia FastMile 4G Receiver Product Overview Blue Red Green Table 10 Second priority Third priority Blinking Bluetooth connection in progress Solid Bluetooth connection established Off No Bluetooth connection Blinking Critical alarm Solid Major or minor alarm Off No alarm Blinking twice per second Kernel and application start up Blinking one per second Application start up Solid Start up Off OAM link is established Status LED behavior for Nokia FastMile 4G Receiver managed from an
Nokia FastMile 4G Receiver Product Overview The signal strength LEDs can be activated by pressing the measurement button on the side of the Compact multi-band models of the Nokia FastMile 4G Receiver. Figure 19 shows the location of the measurement button. Figure 19 Location of the measurement button Measurement button 28885 The signal strength LEDs act as a set to indicate the LTE signal strength detected by the Nokia FastMile 4G Receiver.
Nokia FastMile 4G Receiver Product Overview Power information 11 Power information 11.1 Power information for the Nokia FastMile 4G Receiver 11.1 Power information for the Nokia FastMile 4G Receiver The Nokia FastMile 4G Receiver receives power though a Cat5e shielded Ethernet cable connected to a residential gateway or a PoE injector: • The Compact mono-band and ABA models have a pre-attached 3 m (9.8 ft) Cat5e shielded twisted pair Ethernet cable with a male RJ 45 connector at the free end.
Performance information Nokia FastMile 4G Receiver Product Overview 12 Performance information 12.1 Performance overview 12.2 Throughput information 12.3 Carrier aggregation information 12.4 Power consumption information 12.1 Performance overview This chapter provides the following performance information for the Nokia FastMile 4G Receiver: • throughput information: see section 12.2 • carrier aggregation information: see section 12.3 • power consumption information: section 12.
Nokia FastMile 4G Receiver Product Overview • • • • • • • • • • Performance information Downlink: DL 3xCA 2x2MIMO 256 QAM Uplink: single carrier 64 QAM FDD inter-band 3CA TDD Band 41 intra-Band 3CA, configuration is configuration 2, subframe 7 Base Bandwidth 20M Data rates can have a margin of 2% Packet length is 1470B for UDP Window is 1000k for TCP Data rates are for IPv4 cases Data forwarding working on router model The end-to-end throughput is achieved in the conductive mode with cable connected.
Performance information Nokia FastMile 4G Receiver Product Overview Band Downlink Carrier aggregation support B48 3650 Mhz-3700 MHz Up to 40 MHz bandwidth contiguous 2CA Up to 40 MHz bandwidth non-contiguous 2CA Up to 50 MHz bandwidth contiguous 3CA Up to 50 MHz bandwidth non-contiguous 3CA B3 1805 MHz-1880 MHz Up to 40 MHz bandwidth contiguous 2CA Up to 40 MHz bandwidth non-contiguous 2CA B7 2620 MHz-2690 MHz Up to 40 MHz bandwidth contiguous 2CA Up to 40 MHz bandwidth non-contiguous 2CA Up to
Nokia FastMile 4G Receiver Product Overview B20+B32 Performance information 791 MHz - 821 MHz +1452 MHz - 1496 MHz Up to 40 MHz bandwidth inter band 2CA (1 of 2) Bands Downlinks Uplinks Carrier aggregation support B7+B32 2620 MHz - 2690 MHz +1452 MHz - 1496 MHz Up to 40 MHz bandwidth inter band 2CA B3+B7+B20 1805 MHz - 1880 MHz +2620 MHz - 2690 MHz +791 MHz - 821 MHz Up to 60 MHz bandwidth inter band 3CA B3+B7+B32 1805 MHz - 1880 MHz +2620 MHz - 2690 MHz +1452 MHz - 1496 MHz Up to 60 MHz ba
Performance information Nokia FastMile 4G Receiver Product Overview B41 2496 MHz – 2690 MHz Up to 40 MHz bandwidth contiguous 2CA Up to 60 MHz bandwidth contiguous 3CA Up to 80 MHz bandwidth contiguous 3CA (1 of 2) Band Downlink Carrier aggregation support B20 791 MHz - 821 MHz Up to 30 MHz bandwidth contiguous 2CA Up to 30 MHz bandwidth non-contiguous 2CA B28 758 MHz - 803 MHz Up to 40 MHz bandwidth contiguous 2CA B3+B41 1805 MHz - 1880 MHz +2496 MHz - 2690 MHz Up to 40 MHz bandwidth inter
Nokia FastMile 4G Receiver Product Overview Issue: 01 DRAFT Performance information Maximum power output 7w Idle power 1w 3TG-00386-ABAA-TCZZA DRAFT 61
Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview 13 Management using the Nokia Wireless app 13.1 Using the Nokia Wireless app to manage the Nokia FastMile 4G Receiver 13.2 Using the Nokia Wireless app to manage a unit managed by the Nokia Altiplano FastMile Controller 13.3 Using the Nokia Wireless app to manage a unit managed by an ACS 13.
Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app You will need the QR code that was saved as described during installation the Nokia FastMile 4G Receiver in order to scan it when logging in to it through the Nokia Wireless app.
Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 20 Introductory screen for unit managed by the Nokia Altiplano FastMile Controller through NETCONF Continue by tapping on “Get started”.
Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 21 Screen with prompt to scan the QR code for unit managed by the Nokia Altiplano FastMile Controller through NETCONF Tap on “Scan” to start the scan of the QR code. Use the viewfinder of the phone to align with the QR code. Figure 22 shows the QR code screen.
Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 22 QR code screen for unit managed by the Nokia Altiplano FastMile Controller through NETCONF 3 The Nokia Wireless app displays the screen to install the Nolia FastMile 4G Receiver. Tap on the “Already Installed?” option. Figure 23 shows the Already Installed option.
Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 23 Screen showing the Already Installed option for unit managed by the Nokia Altiplano FastMile Controller through NETCONF 4 The Nokia Wireless app prompts you to connect to the Nokia FastMile 4G Receiver. The connection will be done through a VPN.
Management using the Nokia Wireless app Figure 24 Nokia FastMile 4G Receiver Product Overview Screen for connecting to the Nokia FastMile 4G Receiver Connect to the Nokia FastMile 4G Receiver by tapping on “Connect”. 5 The Nokia Wireless app prompts you to enable the VPN profile for a secure method to communicate with the Nokia FastMile 4G Receiver. Figure 25 shows the screen to enable the VPN profile.
Nokia FastMile 4G Receiver Product Overview Figure 25 Management using the Nokia Wireless app Screen for enabling the VPN profile Enable the VPN profile by tapping on “Connect”. 6 The android system of the mobile phone prompts you to accept the connection request. Figure 26 shows the prompt to accept the connection request.
Management using the Nokia Wireless app Figure 26 Nokia FastMile 4G Receiver Product Overview Prompt for accepting the connection request Accept the connection request by tapping on “OK”. 7 The Nokia Wireless app prompts you to log in to the Nokia FastMile 4G Receiver. You will need to input the username and password for the Nokia FastMile 4G Receiver. Figure 27 shows the screen to log in to the Nokia FastMile 4G Receiver.
Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 27 Screen to log in to a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller Log in to the Nokia FastMile 4G Receiver by tapping on “Log in”.
Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview • status: The current operational state of the PDN connection • EARFCN: The carrier frequency in the uplink and downlink is designated by the E-UTRA. Absolute Radio Frequency Channel Number (EARFCN) in the range 0 - 65535.
Nokia FastMile 4G Receiver Product Overview Figure 28 Management using the Nokia Wireless app System state screen example for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller Note — The Nokia Wireless app will display a value of “N/A” for parameters that are not supported by the installed Home 4G Receiver Software version.
Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 29 System state screen with Beam Angle information for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller 9 You can upload updated certificates (stored under downloads in the mobile phone's directory) to the Nokia FastMile 4G Receiver. i Tap on the “Upload CA certificates” option. Figure 30 shows the screen that has the “Upload CA certificates” option.
Nokia FastMile 4G Receiver Product Overview Figure 30 Management using the Nokia Wireless app Screen that has the “Upload CA certificates” option for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller ii Select the required CA certificates and tap on “Ok”. Note that the certificates must be in the download folder of the mobile phone before you can upload them to the Nokia FastMile 4G Receiver. Figure 31 shows the screen that lists the CA certificates.
Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 31 Screen that lists the CA certificates for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller The following CA certificates are supported for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller through TR-069: • • • • iii 76 pmaCA.pem (used for authenticating the Nokia Altiplano FastMile Controller) logserverCA.
Nokia FastMile 4G Receiver Product Overview Figure 32 Management using the Nokia Wireless app Screen indicating that uploading of the CA certificates was successful for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller Tap on “Ok” to clear the message. 10 You can reboot a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller through NETCONF by tapping on the “Reboot Device” option. Figure 33 shows the “Reboot Device” option.
Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 33 Screen showing the “Reboot Device” option for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller The screen shows the reboot message indicating that the Bluetooth connection will be interrupted and that you will be disconnected. Figure 34 shows the screen that has the reboot message.
Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Figure 34 Screen showing the reboot message for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller Press the Reboot option if you want to proceed with the reboot, or press the Cancel option. If you pressed the Reboot option, press OK.
Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 35 Screen showing the “Perform Factory Reset” option for a Nokia FastMile 4G Receiver managed by the Nokia Altiplano FastMile Controller The screen shows the factory reset message indicating that the factory reset will reset the device back to factory settings and that all changes will be lost and that you will be disconnected. Figure 36 shows the screen that has the factory reset message.
Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Press the Reset option if you want to proceed with the reset to factory settings, or press the Cancel option. If you pressed the Reset option, press OK. 13.
Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview through the Nokia Wireless app.
Nokia FastMile 4G Receiver Product Overview Figure 37 Management using the Nokia Wireless app Introductory screen for unit managed by an ACS through TR-069 Continue by tapping on “Get started”. 2 After the introductory screen has cleared, the Nokia Wireless app shows an animation of how to scan the QR code of the Nokia FastMile 4G Receiver so that the app can obtain the MAC address, unique device identifier, enterprise id, and device type of the Nokia FastMile 4G Receiver.
Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 38 Screen with prompt to scan the QR code for unit managed by an ACS through TR-069 Tap on “Scan” to start the scan of the QR code. Use the viewfinder of the phone to align with the QR code. Figure 39 shows the QR code screen.
Nokia FastMile 4G Receiver Product Overview Figure 39 3 Management using the Nokia Wireless app QR code screen for unit managed by an ACS through TR-069 The Nokia Wireless app displays the screen to install the Nolia FastMile 4G Receiver. Tap on the “Already Installed?” option. Figure 40 shows the Already Installed option.
Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 40 Screen showing the Already Installed option for unit managed by an ACS through TR-069 4 The Nokia Wireless app prompts you to connect to the Nokia FastMile 4G Receiver. The connection will be done through a VPN. You will need to be close to the Nokia FastMile 4G Receiver and you will need to have Bluetooth enabled on the mobile phone and accept the pairing request when it appears.
Nokia FastMile 4G Receiver Product Overview Figure 41 Management using the Nokia Wireless app Screen for connecting to the Nokia FastMile 4G Receiver Connect to the Nokia FastMile 4G Receiver by tapping on “Connect”. 5 The Nokia Wireless app prompts you to enable the VPN profile for a secure method to communicate with the Nokia FastMile 4G Receiver. Figure 42 shows the screen to enable the VPN profile.
Management using the Nokia Wireless app Figure 42 Nokia FastMile 4G Receiver Product Overview Screen for enabling the VPN profile Enable the VPN profile by tapping on “Connect”. 6 The android system of the mobile phone prompts you to accept the connection request. Figure 43 shows the prompt to accept the connection request.
Nokia FastMile 4G Receiver Product Overview Figure 43 Management using the Nokia Wireless app Prompt for accepting the connection request Accept the connection request by tapping on “OK”. 7 The Nokia Wireless app prompts you to log in to the Nokia FastMile 4G Receiver. You will need to input the username and password for the Nokia FastMile 4G Receiver. Figure 44 shows the screen to log in to the Nokia FastMile 4G Receiver.
Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Figure 44 Screen to log in to a Nokia FastMile 4G Receiver managed by an ACS through TR-069 Log in to the Nokia FastMile 4G Receiver by tapping on “Log in”.
Nokia FastMile 4G Receiver Product Overview Management using the Nokia Wireless app Absolute Radio Frequency Channel Number (EARFCN) in the range 0 - 65535.
Management using the Nokia Wireless app Nokia FastMile 4G Receiver Product Overview Note — The Nokia Wireless app will display a value of “N/A” for parameters that are not supported by the installed Home 4G Receiver Software version.
Nokia FastMile 4G Receiver Product Overview Figure 47 Management using the Nokia Wireless app Screen that has the “Upload CA certificates” option for a Nokia FastMile 4G Receiver managed by an ACS ii Select the required CA certificates and tap on “Ok”. Note that the certificates must be in the download folder of the mobile phone before you can upload them to the Nokia FastMile 4G Receiver.
Management using the Nokia Wireless app 10 Nokia FastMile 4G Receiver Product Overview You can reboot a Nokia FastMile 4G Receiver managed by an ACS through TR-069 by tapping on the “Reboot Device” option. Figure 48 shows the “Reboot Device” option.
Nokia FastMile 4G Receiver Product Overview Management using the Web UI 14 Management using the Web UI 14.1 Using the Web UI to manage the Nokia FastMile 4G Receiver 14.2 Using the Web UI status screen 14.3 Using the Web UI network screen 14.4 Using the Web UI system screen 14.
Management using the Web UI Nokia FastMile 4G Receiver Product Overview • Total number of MB sent on the LTE interface since last FastMile 4G Receiver restart • Total number of MB received on the LTE interface since last FastMile 4G • • • • • Receiver restart Total number of MB sent on the Ethernet interface since last FastMile 4G Receiver restart Total number of MB received on the Ethernet interface since last FastMile 4G Receiver restart Data Model (TR-069) Software Version Name and corresponding IP a
Nokia FastMile 4G Receiver Product Overview Figure 50 Management using the Web UI Example of the Status screen when the FastMile 4G Receiver is connected to a cell 14.3 Using the Web UI network screen The Web UI network screen allows you to perform FastMile4G Receiver configuration actions. Login is required. For details on the Web UI login, please refer to the Customer Release Notes.
Management using the Web UI Nokia FastMile 4G Receiver Product Overview • Configuration of Access Points (up to one default AP in router mode and up to four APs in bridge mode; a total of five APs can be configured).
Nokia FastMile 4G Receiver Product Overview Figure 51 Management using the Web UI Example of the Login screen Figure 52 shows an example of the Network screen.
Management using the Web UI Figure 52 Nokia FastMile 4G Receiver Product Overview Example of the Network screen Figure 53 shows an example of scroll down for the Network screen.
Nokia FastMile 4G Receiver Product Overview Figure 53 Management using the Web UI Example of scroll down for the Network screen Figure 54 shows an example of the Add Access Point window.
Management using the Web UI Figure 54 Nokia FastMile 4G Receiver Product Overview Example of the Add Access Point window Figure 55 shows an example of the Delete APN window.
Nokia FastMile 4G Receiver Product Overview Figure 55 Management using the Web UI Example of the Delete APN window Figure 56 shows an example of the Edit Location window.
Management using the Web UI Figure 56 Nokia FastMile 4G Receiver Product Overview Example of the Edit Location window Figure 57 shows an example of the Edit Controller window (used to configure ACSrelated parameters).
Nokia FastMile 4G Receiver Product Overview Figure 57 Management using the Web UI Example of the Edit Controller window Figure 58 shows an example of the Edit DHCP window.
Management using the Web UI Figure 58 Nokia FastMile 4G Receiver Product Overview Example of the Edit DHCP window Figure 59 shows an example of the Certificates information window that opens when you click on Upload Certificate.
Nokia FastMile 4G Receiver Product Overview Figure 59 Management using the Web UI Example of the Certificates information window Figure 60 shows an example of the Add Cell window.
Management using the Web UI Figure 60 Nokia FastMile 4G Receiver Product Overview Example of the Add Cell window Figure 61 shows an example of the Delete Cell window.
Nokia FastMile 4G Receiver Product Overview Figure 61 Management using the Web UI Example of the Delete Cell window 14.4 Using the Web UI system screen The Web UI system screen allows you to perform advanced system actions on the FastMile 4G Receiver. Login is required. For details on the Web UI login, please refer to the Customer Release Notes.
Management using the Web UI Nokia FastMile 4G Receiver Product Overview Figure 62 Example of the System screen Figure 63 Figure 63 shows an example of the Restart Device confirmation window.
Nokia FastMile 4G Receiver Product Overview Management using the Web UI Figure 64 shows an example of the Restore Device confirmation window used to restore the device to factory settings. Figure 64 Example of the Restore Device confirmation window Figure 65 shows an example of the screen that displays while firmware is being updated.
Management using the Web UI Figure 65 112 Nokia FastMile 4G Receiver Product Overview Example of the screen that displays while firmware is being updated 3TG-00386-ABAA-TCZZA DRAFT Issue: 01 DRAFT
Nokia FastMile 4G Receiver Product Overview Issue: 01 DRAFT Management using the Web UI 3TG-00386-ABAA-TCZZA DRAFT 113
Nokia FastMile 4G Receiver Product Overview Standards certification 15 Standards certification 15.1 Standards certification for Compact mono-band and ABA models 15.2 Standards certification for the Compact multi-band models 15.1 Standards certification for Compact monoband and ABA models Table 16 provides standards certification information for the Compact mono-band and ABA models of the Nokia FastMile 4G Receiver.
Nokia FastMile 4G Receiver Product Overview 15.2 Standards certification for the Compact multiband models Table 17 provides standards certification information for the Compact multi-band models of the Nokia FastMile 4G Receiver.
Nokia FastMile 4G Receiver Product Overview Dimensions Compact multi-band models: 22.7 cm by 22.7 cm by 6.4 cm (8.94 in by 8.94 in by 2.52 in) Compact mono-band models: 23.5 cm by 23.5 cm by 5.2 cm (9.3 in by 9.3 in by 2 in) Weight ABA: 31.8 cm by 31.8 cm by 5.6 cm (12.5 in by 12.5 in by 2.2 in) Compact multi-band models: 0.88 kg (1.9 lb) Compact mono-band models: 1.3 kg (2.9 lb) ABA: 2 kg (4.4.
Nokia FastMile 4G Receiver Product Overview Appendix B: RF exposure 17 Appendix B: RF exposure 17.1 RF exposure 17.1 RF exposure The international standard used for the assessment of this device provides simple conformity assessment methods for low power electronic and electrical equipment to an exposure limit relevant to electromagnetic fields (EMF).
Nokia FastMile 4G Receiver Product Overview Appendix C: FCC statements and label instructions 18 Appendix C: FCC statements and label instructions 18.1 FCC compliance statement 18.2 FCC radiation exposure statement 18.3 FCC label instructions 18.1 FCC compliance statement Table 19 provides the FCC ID for the Nokia FastMile 4G Receiver.
Nokia FastMile 4G Receiver Product Overview Glossary 19 Glossary 3GPP This glossary provides the expansions and optional descriptions of most acronyms and initialisms that appear in this document.
Nokia FastMile 4G Receiver Product Overview ETSI European Telecommunications Standards Institute FCC Federal Communications Commission FDD Frequency Division Duplex FM FastMile Glossary HSS Home Subscriber Server IEEE Institute of Electrical and Electronics Engineers IP International Protection or Internet Protocol IPTV Internet Protocol over Television LAN Local Area Network LED Light Emitting Diode LTE Long-Term Evolution MAC Media Access Control MCV Maximum Concentration Value
Nokia FastMile 4G Receiver Product Overview RF Radio Frequency RoHS Restriction of Hazardous Substances RSRP Reference Signal Received Power RSRQ Reference Signal Received Quality RSSI Received Signal Strength Indicator Glossary SIM Subscriber Identify Module SINR Signal-to-Interference-plus-Noise Ratio TCP Transmission Control Protocol TDD Time Division Duplex UDP User Datagram Protocol UL Underwriters’ Laboratories URL Uniform Resource Locater VDC Volts Direct Current VoIP Voic
Nokia FastMile 4G Receiver Product Overview Glossary 122 3TG-00386-ABAA-TCZZA DRAFT Issue: 01 DRAFT
Customer document and product support Customer documentation Customer Documentation Welcome Page Technical Support Customer Documentation Technical Support Documentation feedback Customer Documentation Feedback Copyright 2019 Nokia.
