Changer smart temporal thermometer
INTRODUCTION Package content Withings Thermo Protective cap Two AAA Alkaline (LR3) batteries (already inserted) Notice of use Product description WARNING AND PRECAUTIONS Please read this section carefully before using Withings Thermo thermometer. Intended use – Important safety information The device is intended for use in measuring temperature in adult population, children and babies population. This device is not suitable for children born before term.
General safety - Do not use the device on premature babies (babies born before term) Do not use this device for purpose other than the one described in this manual Keep the device out the reach of children. Children must not play, swallow or eat the device. This device is for personal use at home only. The sensor lens is fragile: do not touch it with your fingers. Do not expose the device to humidity or water. In case the unit is wet, wait until it is dry.
AFTER USE Cleaning – Do not use an alcoholic-base or solvent agent to clean the device – Clean the device with a soft and dry cloth – Do not submerge the device or any of the components in water. Ensure that no liquid enters the interior of the thermometer. – Do not dismantle the device or try to repair it by yourself.
3. Replace the AAA alkaline cells “Low battery icon” “Error” “Error” The temperature seems rather high Battery is low The temperature is outside ranges. Body mode : lower than 35°C (95°F) or higher than 43.2°C (109.76°F) Surface mode : lower than 22°C (71.
Replacing the AAA alkaline cells If the low battery symbol appears in the Withings application, replace all two AAA alkaline cells at the same time. 1. Remove the AAA alkaline cells cover at the back of the thermometer. 2. Install or replace two AAA alkaline cells so that the + (positive) and – (negative) polarities match the polarities indicated on the AAA alkaline cells compartment. 3. Put the AAA alkaline cells cover back in place.
Type BF FCC ID : XNASCT01 Storage temperature Keep it dry
FCC STATEMENT Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
RF STATEMENT Medical Electrical Equipment needs special precautions regarding EMC and needs to be installed and put into service according to the EMC information provided in the following. – Interference may occur in the vicinity of equipment marked with – Portable and mobile RF communication equipment (e.g. cell phones) can affect Medical Electrical Equipment.
EMC DATA Declaration – electromagnetic emissions and immunity for equipment and systems that are not life-supporting and are specified for use only in a shielded location Non-Life Support Equipment Separation Distance Calculation (3Vrms / 3V/m compliance) Rated maximum output Separation distance according to frequency of transmitter (m) power of transmitter (W) 150 kHz to 80 MHz to 800 MHz 800 MHz to 2.5 GHz 80 MHz in d = [3,5] P E1 d = [ 7 ] P E1 ISM bands d = [3,5] P V1 0.01 0.12 0.12 0.23 0.1 0.37 0.
(ESD)IEC 610004-2 Electrical fast transient/burst IEC 61000-4-4 Surge IEC 610004-5 Voltage dips, short interruptions and voltage variations on power supply input lines IEC 61000-4-11 Power frequency (50/60 Hz) magnetic field IEC 61000-4-8 2 kV for power supply lines 1 kV for input/output lines 1 kV differential mode 2 kV common mode -5 % UT(95% dip in UT) for 0.
Reference to standards This device complies with the following normative documents : COUNCIL DIRECTIVE 93/42/EEC of 14 June 1993 concerning medical devices as amended by Directive 2007/47/EC – EN ISO 80601-2-56 : Particular requirements for basic safety and essential performance of clinical thermometers for body temperature measurement – EN ISO 12470-5: 2003 : “Clinical thermometers” – Part 5: Performance of infrared thermometers (with maximum device) – ASTM 1965E : ASTM Standard for Infrared Clinical Therm
