Draft 7368 Intelligent Services Access Manager ONT G-2426G-A Product Guide 3FE-XXXXX-AAAA-TCZZA Issue 1 September 2020 Draft Nokia – Proprietary and Confidential Use pursuant to applicable agreements
Draft 7368 ISAM ONT Legal notice Nokia is a registered trademark of Nokia Corporation. Other products and company names mentioned herein may be trademarks or tradenames of their respective owners. The information presented is subject to change without notice. No responsibility is assumed for inaccuracies contained herein. © 2020 Nokia.
Contents 7368 ISAM ONT Draft Contents About this document............................................................................................................................................7 1 2 3 4 ETSI ONT safety guidelines ........................................................................................................................13 1.1 Safety instructions............................................................................................................................
Draft Contents 5 6 7 7368 ISAM ONT Install a G-2426G-A indoor ONT..................................................................................................................55 5.1 Overview ...........................................................................................................................................55 5.2 Purpose.............................................................................................................................................55 5.
7368 ISAM ONT 7.17 Configuring WAN...............................................................................................................................93 7.18 Configuring WAN DHCP ...................................................................................................................95 7.19 Configuring Wireless 2.4GHz............................................................................................................97 7.20 Configuring Wireless 5GHz.......................
Draft Contents 7368 ISAM ONT 7.51 Backing up the configuration...........................................................................................................158 7.52 Restoring the configuration .............................................................................................................159 7.53 Upgrading firmware.........................................................................................................................160 7.54 Rebooting the device .........
About this document 7368 ISAM ONT Draft About this document Purpose This documentation set provides information about safety, features and functionality, ordering, hardware installation and maintenance, and software installation procedures of this ONT for the current release. Intended audience This documentation set is intended for planners, administrators, operators, and maintenance personnel involved in installing, upgrading, or maintaining the ONTs.
Draft About this document 7368 ISAM ONT Nokia quality processes Nokia’s ONT manufacturing, testing, and inspecting practices are in compliance with TL 9000 requirements. These requirements are documented in the Fixed Networks Quality Manual 3FQ30146-6000-QRZZA. The quality practices adequately ensure that technical requirements and customer end-point requirements are met.
About this document 7368 ISAM ONT Draft 1 Navigate to http://customer.nokia.com/s/ and enter your user name and password. If you are a new user and require access to this service, please contact your Nokia sales representative. 2 Select Products. 3 Type your product name in the Find and select a product field and click the search icon. Select a product. 4 Click Documentation: Doc Center to go to the product page in the Doc Center. 5 Select a release from the Release list and click SEARCH.
Draft About this document 7368 ISAM ONT 1 This step has a series of substeps that you must perform to complete the step. You must perform the following substeps: a. This is the first substep. b. This is the second substep. c. This is the third substep. 2 You must perform this step. END OF STEPS Multiple PDF document search You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a common term. Adobe Reader displays the results in a single display panel.
About this document 7368 ISAM ONT Draft Technical support For details, refer to the Nokia Support portal (https://customer.nokia.com/support/s/). For ordering information, contact your Nokia sales representative. How to comment Note to reviewers: The following "How to comment" text will appear in the final document when it is published. However, the feedback method described below is for use only on final documents.
Draft Draft About this document 7368 ISAM ONT Nokia – Proprietary and Confidential Use pursuant to applicable agreements 12 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1
ETSI ONT safety guidelines Safety instructions 7368 ISAM ONT Draft 1 ETSI ONT safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals (ONTs). 1.1 Safety instructions This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment. 1.1.1 Safety instruction boxes The safety instruction boxes are provided in the ONT customer documentation.
Draft ETSI ONT safety guidelines Safety instructions 7368 ISAM ONT CAUTION Service Disruption Possibility of service interruption. Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. The following is an example of the Note box. Note: Information of special interest.
ETSI ONT safety guidelines Safety standards compliance Draft 1.2 7368 ISAM ONT Safety standards compliance This section describes the ONT compliance with the European safety standards. 1.2.1 EMC, EMI, and ESD compliance The ONT equipment complies with the following EMC, EMI, and ESD requirements: • EN 300-328 v1.9.1 wide band data transmission standards for 2.4GHz bands • EN 300-386 V1.5.
Draft ETSI ONT safety guidelines ESD safety guidelines 7368 ISAM ONT The ONTs comply with BS EN 61140. 1.3.1 Power supplies The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property. 1.3.
ETSI ONT safety guidelines Laser safety guidelines 7368 ISAM ONT Draft DANGER Hazard There may be invisible laser radiation at the fiber optic cable when the cable is removed from the connector. Avoid direct exposure to the laser beam. Observe the following danger for laser hazard. Eyes can be damaged when they are exposed to a laser beam. Take necessary precautions before you plug in the optical modules. DANGER Hazard Possibility of equipment damage. Risk of eye damage by laser radiation. 1.5.
Draft ETSI ONT safety guidelines Laser safety guidelines Figure 1-3 7368 ISAM ONT Laser classification label CLASS 1 LASER PRODUCT ' PRODUCTO LASER CLASE 1 ' CLASE 1 DEL LASER LASER CLASSE 1 18992 Figure 1-4, “Laser warning labels” (p. 19) shows a laser warning label and an explanatory label for laser products. Labels and warning may be provided in other languages.
ETSI ONT safety guidelines Laser safety guidelines Draft Figure 1-4 7368 ISAM ONT Laser warning labels INVISIBLE LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Wavelength(s): xxxx nm Normal output power: xx m W Max output power: yyy m W Laser Warning Label Laser Warning Label CLASS 1 LASER PRODUCT RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE EVITER TOUTE EXPOSITION AU FAISCEAU NE PAS DEMONTER.
Draft ETSI ONT safety guidelines Environmental requirements 1.6 7368 ISAM ONT Environmental requirements See the ONT technical specification documentation for more information about temperature ranges. During operation in the supported temperature range, condensation inside the ONT caused by humidity is not an issue.
7368 ISAM ONT Draft ETSI environmental and CRoHS guidelines Environmental labels 2 ETSI environmental and CRoHS guidelines This chapter provides information about the ETSI environmental China Restriction of Hazardous Substances (CRoHS) regulations that govern the installation and operation of the optical line termination (OLT) and optical network termination (ONT) systems. This chapter also includes environmental operation parameters of general interest. 2.
Draft ETSI environmental and CRoHS guidelines Environmental labels Figure 2-1 7368 ISAM ONT Products below MCV value label 18986 Products containing hazardous substances above Maximum Concentration Value (MCV) label Figure 2-2, “Products above MCV value label” (p. 22) shows the label that indicates a product is above the maximum concentration value, as defined by standard SJ/T11363-2006 (Requirements for Concentration Limits for Certain Hazardous Substances in Electronic Information Products).
7368 ISAM ONT Draft ETSI environmental and CRoHS guidelines Hazardous Substances Table (HST) environments, and physical condition of infrastructure and handsets after years of service. The values reflect minimum values and refer to products operated according to the intended use conditions. See 2.2 “Hazardous Substances Table (HST)” (p. 22) for more information. 2.
Draft ETSI environmental and CRoHS guidelines Other environmental requirements 7368 ISAM ONT compliance with the European Union Directive 2011/65/EU on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (RoHS2). With the process equipment is assessed in accordance with the Harmonised Standard EN50581:2012 (CENELEC) on Technical documentation for the assessment of electrical and electronic products with respect to the restriction of hazardous substances. 2.
ANSI ONT safety guidelines Safety instructions 7368 ISAM ONT Draft 3 ANSI ONT safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals or units (ONTs or ONUs) in the North American or ANSI market. 3.1 Safety instructions This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment. 3.1.
Draft ANSI ONT safety guidelines Safety instructions 7368 ISAM ONT CAUTION Service Disruption Possibility of service interruption. Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. The following is an example of the Note box. Note: Information of special interest.
ANSI ONT safety guidelines Safety standards compliance 7368 ISAM ONT Draft Figure 3-1, “Sample safety label on the ONT equipment” (p. 26) shows a sample safety label on the ONT equipment. Figure 3-1 Sample safety label on the ONT equipment Tested to Comply with FCC Standards FOR HOME OR OFFICE USE c ® COMMUNICATION SERVICE EQUIPMENT US LISTED 27FY Type 3R Enclosure - Rainproof This device complies with Part 15 of the FCC Rules.
Draft ANSI ONT safety guidelines Safety standards compliance 7368 ISAM ONT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
ANSI ONT safety guidelines Laser safety guidelines Draft Figure 3-2 7368 ISAM ONT Sample laser product label showing CDRH 21 CFR compliance Model: MFG: MONTH: XX YEAR: XXXX ICS: XX MRev: XX 3FE55851ABAA MAC:XXXXXXXXXXXX SN:ALCLXXXXXXXX I.T.E CLASS 1 LASER PRODUCT PRODUIT LASER DE CLASSE 1 FCC ID: XXXXXXXXXXX 12VDC 3A ASSEMBLED IN CHINA 2301 Sugar Bush Rd. Raleigh, NC 27612 Intertek 4006119 This device complies with Part 15 of the FCC Rule.
Draft ANSI ONT safety guidelines Laser safety guidelines 7368 ISAM ONT Per CDRH 21 CFR 10.40.10 (h) (1) (iv) distributors of Class 1 laser products, such as Nokia ONTs shall leave the following Laser Safety cautions with the end user. a) “Class 1 Laser Product” b) “Caution – Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.” 3.3.
ANSI ONT safety guidelines Laser safety guidelines 7368 ISAM ONT Draft • wavelength • normal output power • maximum output power Figure 3-5 Laser warning labels INVISIBLE LASER RADIATION DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Wavelength(s): xxxx nm Normal output power: xx m W Max output power: yyy m W Laser Warning Label Laser Warning Label CLASS 1 LASER PRODUCT RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE EVITER TOUTE EXPOSITION AU FAISCEAU NE PAS DEMONTER.
Draft ANSI ONT safety guidelines Electrical safety guidelines Figure 3-6 7368 ISAM ONT Sample laser product safety label on the ONT equipment Model: MFG: MONTH: XX YEAR: XXXX ICS: XX MRev: XX 3FE55851ABAA MAC:XXXXXXXXXXXX SN:ALCLXXXXXXXX I.T.E CLASS 1 LASER PRODUCT PRODUIT LASER DE CLASSE 1 FCC ID: XXXXXXXXXXX 12VDC 3A ASSEMBLED IN CHINA 2301 Sugar Bush Rd. Raleigh, NC 27612 Intertek 4006119 This device complies with Part 15 of the FCC Rule.
ANSI ONT safety guidelines ESD safety guidelines Draft 3.4.1 7368 ISAM ONT Power supplies The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property. 3.4.2 Cabling The following are the guidelines regarding cables used for the ONT equipment: • Use only cables approved by the relevant national electrical code.
Draft Draft ANSI ONT safety guidelines Environmental requirements 7368 ISAM ONT • When high humidity is present, installation of a cover or tent over the ONT helps prevent condensation when the door is opened.
G-2426G-A unit data sheet Overview 7368 ISAM ONT Draft 4 G-2426G-A unit data sheet 4.1 Overview 4.1.1 Purpose 4.1.2 Contents 4.2 4.1 Overview 35 4.2 G-2426G-A part numbers and identification 35 4.3 G-2426G-A general description 37 4.4 G-2426G-A software and installation feature support 43 4.5 G-2426G-A interfaces and interface capacity 43 4.6 G-2426G-A LEDs 45 4.7 G-2426G-A detailed specifications 47 4.8 G-2426G-A GEM ports and T-CONTs 48 4.
Draft G-2426G-A unit data sheet G-2426G-A part numbers and identification 7368 ISAM ONT Table 4-1 Identification of G-2426G-A indoor ONTs (continued) Ordering kit part number Provisioning number Description CLEI Code CPR ECI/ Bar code 3FE 49220 BB Customer specific variant 3FE 49241 BB G-2426G-A, EU Plug,GPON ONT. Supports 2 POTS port,4xGE UNI, WIFI 6 2+2 — — — 3FE 49220 CA 3FE 49241 BA — — — Includes one USB 3.
G-2426G-A unit data sheet G-2426G-A general description 7368 ISAM ONT Draft Table 4-3 G-2426G-A power supply ordering information ONT part numbers Power model (Model No.
Draft G-2426G-A unit data sheet G-2426G-A general description 7368 ISAM ONT USB TEL1 TEL2 LAN1 LAN2 LAN3 LAN4 POWER WPS LED WLAN RESET ON/OFF On/off button Reset POTS port Ethernet ports (4) Power Wi-Fi button (RJ-11) (RJ-45) security/ on/off buttons USB port 36176 Figure 4-1 G-2426G-A (internal antenna) POWER LINK AUTH LAN1 LAN2 LAN3 LAN4 WPS WLAN2.
G-2426G-A unit data sheet G-2426G-A general description 7368 ISAM ONT Draft • Dual-band concurrent 2x2 IEEE 802.11b/g/n 2.4 GHz and 802.11ac MIMO 5 GHz • Supports 802.11 b/g/n 2x2 Wireless 2.4 GHz MIMO; Channel bandwidth 20, 40 MHz, auto • Supports 802.11ac 2x2 Wireless 5 GHz Mu-MIMO; Channel bandwidth 20, 40, 80 MHz, auto • Four Gigabit standard RJ-45 10/100/1000 Mbps, auto negotiating Ethernet ports and MDI/MDIX auto sensing • Two POTS ports with R-J11 connectors • Two USB 2.
Draft G-2426G-A unit data sheet G-2426G-A general description 7368 ISAM ONT • Forward Error Correction (FEC) • support for multiple SSIDs (private and public instances); contact your Nokia representative for further details. • Conductive power: 250mW/24 dBm (2.4 GHz); 500 mW/27 dBm (5GHz) • Maximum effective isotropic radiated power (EIRP): − 5dBi external antenna: 800mW/29dBm (2.4GHz);1600mW/32dBm (5GHz) − 3dBi internal antenna: 500mW/27dBm (2.
G-2426G-A unit data sheet G-2426G-A general description 7368 ISAM ONT Draft The ONT provides host object support for: InternetGatewayDeviceLANDevice.Hosts.Host. Port forwarding support The ONT supports the port forwarding of objects via TR-069: • Application Name • WAN Port • LAN Port • Internal Client • Protocol • Enable Mapping • WAN Connection List These are the same port forwarding parameters supported in the GUI. For more information, see Table 7-32, “Port Forwarding parameters” (p.
Draft G-2426G-A unit data sheet G-2426G-A general description 7368 ISAM ONT Diagnostic parameter support The ONT supports the following TR-069 diagnostic parameters: • TR-143 • IP ping • traceroute These are the same diagnostic parameters supported in the GUI. For more information, see 7.56 “Diagnosing WAN connections” (p. 163) in Chapter 7, “Configure a G-2426G-A indoor ONT”. 4.3.
7368 ISAM ONT Draft G-2426G-A unit data sheet G-2426G-A software and installation feature support • ringers test 4.3.6 TR-111 support The G-2426G-A ONT supports TR-111, which extends the WAN Management Protocol defined in TR-069 to enhance the ability to remotely manage LAN devices. The device-gateway association enables an ACS to identify the associated gateway through which a device is connected.
Draft G-2426G-A unit data sheet G-2426G-A interfaces and interface capacity 7368 ISAM ONT Table 4-4 G-2426G-A indoor ONT interface connection capacity ONT type and model G-2426G-A 1 Maximum capacity POTS 10/ 100 BASE-T 10/ 100/ 1000 BASE-T RF video (CATV) MoCA VDSL2 E1/T1 Local craft GPON SC/APC 2 — 4 — — — — — 1 Notes: 1. The G-2426G-A ONTs provide Wi-Fi service that is enabled and disabled using a Wi-Fi on/off switch. 4.5.
G-2426G-A unit data sheet G-2426G-A LEDs 7368 ISAM ONT Draft Table 4-5 G-2426G-A indoor ONT physical connections Connection 1 Print Letters Description POTS port TEL1 and TEL2 This connection is provided through an RJ-11 port. One POTS connection is supported.The POTS port supports voice services. Ethernet ports LAN1 to LAN4 This connection is provided through Ethernet RJ-45 connectors. Up to four 10/100/1000 Base-T Ethernet interfaces are supported.
Draft G-2426G-A unit data sheet G-2426G-A LEDs Figure 4-2 POWER 7368 ISAM ONT G-2426G-A indoor ONT LEDs LINK AUTH LAN1 LAN2 LAN3 POWER LINK LAN4 AUTH LAN1 LAN2 WPS LAN3 LAN4 WPS WLAN2.4G WLAN5G WLAN2.4G WLAN5G TEL1 TEL2 TEL1 TEL2 VOIP INTERNET USB VOIP INTERNET USB 36235 Table 4-6, “G-2426G-A indoor ONT LED descriptions” (p. 46) provides LED descriptions for G-2426G-A indoor ONTs.
G-2426G-A unit data sheet G-2426G-A detailed specifications 7368 ISAM ONT Draft Table 4-6 G-2426G-A indoor ONT LED descriptions (continued) Indicator LED color and behavior LED behavior description TEL 1 to 2 Green solid Green flashing Off Phone is off hook.
Draft G-2426G-A unit data sheet G-2426G-A GEM ports and T-CONTs 7368 ISAM ONT Table 4-8, “G-2426G-A indoor ONT power consumption specifications” (p. 47) lists the power consumption specifications for G-2426G-A indoor ONT. Table 4-8 G-2426G-A indoor ONT power consumption specifications Mnemonic Maximum power (Not to exceed) Condition Minimum power Condition G-2426G-A 1 24 W 1 POTS off-hook, 4 10/100/1000 Base-T Ethernet, Wi-Fi operational, USB operational 3.
G-2426G-A unit data sheet G-2426G-A performance monitoring statistics 7368 ISAM ONT Draft • Table 4-11, “Package S ONTs ONTENET performance monitoring statistics” (p. 48) provides statistics for ONTENET type counters • Table 4-12, “Package S ONTs ONTL2UNI performance monitoring statistics” (p. 49) provides statistics for ONTL2UNI type counters • Table 4-13, “Package S ONTs PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP performance monitoring statistics” (p.
7368 ISAM ONT Table 4-13 Package S ONTs PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP performance monitoring statistics RXFRAGS LOSTFRAGS BADGEMHDRS 1 RXBLOCKS G-2426G-A PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP statistics TXFRAGS ONT TXBLOCKS Draft G-2426G-A unit data sheet G-2426G-A functional blocks ✓ ✓ ✓ ✓ ✓ — Notes: 1.
G-2426G-A unit data sheet G-2426G-A standards compliance Draft Figure 4-3 7368 ISAM ONT G-2426G-A ONT functional block Flash: 256 MB 2x2 11ax 2.4GHz Wifi power: 500mW conductive FEM GPON BoSA MT7905D MT7975 FEM UART 2x2 11ax 5GHz Wifi power: 500W conductive SoC JTAG USB 2.0 Buttons LEDs transformer 4x1G (RJ45) 36173 4.
Draft G-2426G-A unit data sheet G-2426G-A standards compliance 4.11.1 7368 ISAM ONT Energy-related products standby and off modes compliance Hereby, Nokia declares that the G-2426G-A ONTs are in compliance with the essential requirements and other relevant provisions of Directive 2009/125/EC together with Commission Regulation (EC) No 1275/2008 and Commission Regulation (EC) No 801/2013. The G-2426G-A ONTS qualify as equipment with high network availability (HiNA) functionality.
G-2426G-A unit data sheet G-2426G-A special considerations 7368 ISAM ONT Draft CAUTION Service Disruption Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 4.12 G-2426G-A special considerations G-2426G-A is a package P ONT. 4.12.1 Wi-Fi service G-2426G-A indoor ONTs feature Wi-Fi service as well as voice and data services.
Draft G-2426G-A unit data sheet G-2426G-A special considerations 7368 ISAM ONT Table 4-15 G-2426G-A ONT considerations and limitations Considerations and limitations Call History Data collection (ONTCALLHST) is supported, except for the following parameters: RTP packets (discarded), far-end RTCP and RTCP-XR participation, RTCP average and peak round trip delay, MOS, average jitter, number of jitter-buffer over-runs and under runs.
Install a G-2426G-A indoor ONT Overview 7368 ISAM ONT Draft 5 Install a G-2426G-A indoor ONT 5.1 Overview 5.1.1 Purpose 5.1.2 Contents 5.1 Overview 55 5.2 Purpose 55 5.3 General 55 5.4 Prerequisites 55 5.5 Recommended tools 55 5.6 Safety information 56 5.7 Procedure 56 5.2 Purpose This chapter provides the steps to install a G-2426G-A indoor ONT. 5.3 General The steps listed in this chapter describe mounting and cabling for a G-2426G-A indoor ONT. 5.
Draft Install a G-2426G-A indoor ONT Safety information 7368 ISAM ONT • drill and drill bits • paper clip 5.6 Safety information Read the following safety information before installing the unit. DANGER Hazard Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits.
Install a G-2426G-A indoor ONT Procedure 7368 ISAM ONT Draft 1 Place the indoor ONT unit on a flat surface, such as a desk or shelf. Note: The G-2426G-A cannot be stacked with another ONT or with other equipment.
Draft Install a G-2426G-A indoor ONT Procedure 7368 ISAM ONT 5 DANGER Hazard Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. WARNING Equipment Damage Be careful to maintain a bend radius of no less than 1.5 in. (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber.
Install a G-2426G-A indoor ONT Procedure 7368 ISAM ONT Draft 12 If necessary, reset the ONT. a. Locate the Reset button on a G-2426G-A indoor ONT as shown in Figure 5-1, “G-2426G-A ONT connections” (p. 57). b. Insert the end of a straightened paper clip or other narrow object into the hole in the Reset button to reset the ONT.
Draft Draft Install a G-2426G-A indoor ONT Procedure 7368 ISAM ONT Nokia – Proprietary and Confidential Use pursuant to applicable agreements 60 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1
Replace a G-2426G-A indoor ONT Overview 7368 ISAM ONT Draft 6 Replace a G-2426G-A indoor ONT 6.1 Overview 6.1.1 Purpose 6.1.2 Contents 6.2 6.1 Overview 61 6.2 Purpose 61 6.3 General 61 6.4 Prerequisites 61 6.5 Recommended tools 61 6.6 Safety information 62 6.7 Procedure 62 Purpose This chapter provides the steps to replace a G-2426G-A indoor ONT. 6.3 General The steps listed in this chapter describe mounting and cabling for a G-2426G-A indoor ONT. 6.
Draft Replace a G-2426G-A indoor ONT Safety information 7368 ISAM ONT • drill and drill bits 6.6 Safety information Read the following safety information before replacing the unit. DANGER Hazard Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits. Make sure all sources of power are turned off and have no live voltages present on feed lines or terminals.
Replace a G-2426G-A indoor ONT Procedure 7368 ISAM ONT Draft 1 Deactivate the ONT services at the P-OLT. If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). a. Use the RTRV-ONT command to verify the ONT status and th associated services. Record the serial number or the SLID of the ONT displayed in the command output. Example: RTRV-ONT::ONT-1-1-1-1-1; b. If the ONT is in service, place the ONT in OOS state.
Draft Replace a G-2426G-A indoor ONT Procedure 7368 ISAM ONT 3 Power down the unit by using the on/off power switch. 4 Disconnect the POTS, Ethernet, and power cables from the ONT; see Figure 6-1, “G-2426G-A indoor ONT connections” (p. 63) for the connector locations on the G-2426G-A indoor ONT. 5 DANGER Hazard Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. Disconnect the fiber optic cables. a.
Replace a G-2426G-A indoor ONT Procedure 7368 ISAM ONT Draft 10 DANGER Hazard Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. WARNING Equipment Damage Be careful to maintain a bend radius of no less than 1.5 in. (3.8 cm) when connecting the fiber optic cable. Too small of a bend radius in the cable can result in damage to the optic fiber.
Draft Replace a G-2426G-A indoor ONT Procedure 7368 ISAM ONT 16 Activate and test the services; see the 7368 Hardware and Cabling Installation Guide. 17 If necessary, reset the ONT. a. Locate the Reset button on a G-2426G-A indoor ONT as shown in Figure 6-1, “G-2426G-A indoor ONT connections” (p. 63). b. Insert the end of a straightened paper clip or other narrow object into the hole in the Reset button to reset the ONT.
Configure a G-2426G-A indoor ONT Overview 7368 ISAM ONT Draft 7 Configure a G-2426G-A indoor ONT 7.1 Overview 7.1.1 Purpose 7.1.2 Contents 67 GUI configuration 70 7.2 General configuration 70 7.3 HGU mode GUI configuration 70 7.4 Log in to the web-based GUI 70 Viewing device information and connection status 72 7.5 Overview 72 7.6 Viewing device information 72 7.7 Viewing LAN status 74 7.8 Viewing WAN status 76 7.9 Viewing WAN IPv6 status 78 7.
Draft Draft Configure a G-2426G-A indoor ONT Overview 7368 ISAM ONT 7.22 Configuring IP routing 105 7.23 Configuring DNS 107 7.24 Configuring TR-069 109 7.25 Configuring GRE tunnel 110 7.26 Configuring Upstream (US) Classifier 112 7.27 Configuring QoS 119 Security configuration 123 7.28 Overview 123 7.29 Configuring the firewall 123 7.30 Configuring the MAC filter 124 7.31 Configuring the IP filter 126 7.32 Configuring the URL filter 128 7.33 Configuring parental control 129 7.
Configure a G-2426G-A indoor ONT Overview 7.50 Managing the device 156 7.51 Backing up the configuration 158 7.52 Restoring the configuration 159 7.53 Upgrading firmware 160 7.54 Rebooting the device 161 7.55 Resetting to factory defaults 162 7.56 Diagnosing WAN connections 163 7.57 Viewing log files 164 RG Troubleshooting Counters 167 7.58 Overview 167 7.
Draft Configure a G-2426G-A indoor ONT GUI configuration General configuration 7368 ISAM ONT GUI configuration 7.2 General configuration Refer to the configuration information provided with your OLT for the software configuration procedure for a G-2426G-A ONT. For HTTP configuration procedures, please refer to the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide. 7.3 HGU mode GUI configuration Use the procedures below to use the web-based GUI for the G-2426G-A in HGU mode.
Configure a G-2426G-A indoor ONT GUI configuration Log in to the web-based GUI Draft Figure 7-1 7368 ISAM ONT Web login page Note: If you forget the current username and password, press the reset button for 5 seconds and the default values for the username and password will be recovered at startup. 3 Click Login. The Device Information page displays.
Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Overview 7368 ISAM ONT Viewing device information and connection status 7.5 7.5.1 Overview Purpose This chapter describes procedures to view device information and connection status on the G-2426G-A. 7.5.2 7.6 Contents 7.5 Overview 72 7.6 Viewing device information 72 7.7 Viewing LAN status 74 7.8 Viewing WAN status 76 7.9 Viewing WAN IPv6 status 78 7.10 Viewing home networking information 80 7.
Figure 7-2 7368 ISAM ONT Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing device information Device Information page Note: Upon login, the GPON Home Gateway window displays the WAN status block on the bottom left part of each window. This block shows the WAN connection ID, the WAN status, and any WAN errors. This block is accurate upon login, but it is static; click Refresh to update the information.
Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing LAN status 7368 ISAM ONT Table 7-1 Device Information parameters (continued) Field Description Device Running Time Amount of time the device has run since last reset in hours, minutes, and seconds 2 Click Refresh to update the displayed information. END OF STEPS 7.7 Viewing LAN status 1 Draft Click Status→LAN Status from the left pane in the GPON Home Gateway page.
Figure 7-3 LAN Status page Draft September 2020 Issue 1 7368 ISAM ONT Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing LAN status Nokia – Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA 75
Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing WAN status 7368 ISAM ONT Table 7-2 LAN Status parameters Field Description Wireless Information Wireless Status Indicates whether the wireless is on or off Wireless Channel Wireless channel number SSID Name Name of each SSID Wireless Encryption Status Encryption type used on the wireless connection Wireless Rx Packets Number of packets received on the wireless connection Wireless Tx Packets Number
Figure 7-4 7368 ISAM ONT Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing WAN status WAN Status page Table 7-3 WAN Status parameters Field Description WAN Connection List Drop-down menu listing all WAN connections. The connection shown is the connection for which WAN status will be shown.
Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing WAN IPv6 status 7368 ISAM ONT Table 7-3 WAN Status parameters (continued) Field Description Primary DNS Primary Domain Name Server Second DNS Secondary Domain Name Server Manual DNS Manual Domain Name Server PON Link Status Whether the PON link is up or down Tx Packets Number of packets transmitted on the WAN connection Rx Packets Number of packets received on the WAN connection Tx Dropped Numbe
Figure 7-5 7368 ISAM ONT Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing WAN IPv6 status WAN Status IPv6 page Table 7-4 WAN Status IPv6 parameters Field Description WAN Connection List Drop-down menu listing all WAN connections. The connection shown is the connection for which WAN status will be shown.
Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing home networking information 7368 ISAM ONT Table 7-4 WAN Status IPv6 parameters (continued) Field Description IPv6 Gateway IPv6 gateway address Primary DNS Primary Domain Name Server Second DNS Secondary Domain Name Server PON Link Status Whether the PON link is up or down Tx Packets Number of packets transmitted on the WAN connection Rx Packets Number of packets received on the WAN connection Tx
Figure 7-6 Home Networking page Draft September 2020 Issue 1 7368 ISAM ONT Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing home networking information Nokia – Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA 81
Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing Optics module status 7368 ISAM ONT Table 7-5 Home Networking parameters Field Description Local Interface Ethernet Table displays the number of Ethernet connections and their settings Wireless Table displays the number of wireless connections and their settings (2.4GHz and 5GHz) Wireless Settings (2.
Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing Optics module status Draft Figure 7-7 7368 ISAM ONT Optics Module Status page Table 7-6 Optics Module Status parameters Field Description Laser Bias Current (ONT ANI-ONT-Side Optical Measurements) Laser bias current, measured in uA Optics Module Voltage (ONT ANI-ONT-Side Optical Measurements) Optics module voltage, measured in V Optics Module Temperature (ONT ANI-ONT-Side Optical Measurements) Optics module
Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing statistics 7368 ISAM ONT 2 Click Refresh to display up-to-date information. END OF STEPS 7.12 Viewing statistics 1 Click Status→Statistics from the left pane in the GPON Home Gateway page. The Statistics page displays. Statistics are available for LAN ports, WAN ports, and WLAN ports. Select the LAN tab, WAN tab or WLAN tab to view the respective ports.
Figure 7-9 WAN Statistics page Draft September 2020 Issue 1 7368 ISAM ONT Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing statistics Nokia – Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA 85
Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing voice information 7368 ISAM ONT Figure 7-10 WLAN Statistics page END OF STEPS 7.13 Viewing voice information 1 Draft Click Status→Voice Information from the left pane in the GPON Home Gateway page.
Figure 7-11 7368 ISAM ONT Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing voice information Voice Information page Table 7-7 Voice Information parameters Field Description Line Select a line from the list. The default is Line 1.
Draft Configure a G-2426G-A indoor ONT Viewing device information and connection status Viewing voice information 7368 ISAM ONT Table 7-7 Voice Information parameters (continued) Field Description Phone number Phone number configured for a telephone line 1; For example, +13290611266 Register Status The default is Registered Blank if no voice service is provisioned Register Error Code SIP standard error code for the register status; for example, 401, 403, 503 This field is blank if the register is
Configure a G-2426G-A indoor ONT Network configuration Overview 7368 ISAM ONT Draft Network configuration 7.14 7.14.1 Overview Purpose This chapter describes the network configuration tasks supported by G-2426G-A ONTs. 7.14.2 Contents 7.14 Overview 89 7.15 Configuring LAN 89 7.16 Configuring LAN IPv6 92 7.17 Configuring WAN 93 7.18 Configuring WAN DHCP 95 7.19 Configuring Wireless 2.4GHz 97 7.20 Configuring Wireless 5GHz 100 7.21 Configuring wireless scheduling 103 7.
Draft Configure a G-2426G-A indoor ONT Network configuration Configuring LAN 7368 ISAM ONT Figure 7-12 LAN page 2 Draft Configure the following LAN parameters: Nokia – Proprietary and Confidential Use pursuant to applicable agreements 90 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1
Configure a G-2426G-A indoor ONT Network configuration Configuring LAN 7368 ISAM ONT Draft Table 7-8 LAN parameters Field Description Port Mode All Ports to Bridge Mode Select this checkbox to set all ports to bridge mode. Port 1 - 4 Select the port mode for each port and click Save: • Route Mode • Bridge Mode IPv4 Address Enter the IP address of the ONT. Subnet Mask Enter the subnet mask of the ONT. DHCP enable Select this checkbox to enable DHCP.
Draft Configure a G-2426G-A indoor ONT Network configuration Configuring LAN IPv6 7.16 7368 ISAM ONT Configuring LAN IPv6 1 Click Network→LAN_IPv6 from the left pane in the GPON Home Gateway page. The LAN_ IPv6 page displays.
Configure a G-2426G-A indoor ONT Network configuration Configuring WAN 7368 ISAM ONT Draft Table 7-10 LAN IPv6 parameters Field Description IPv6 LAN Host Configuration DNS Server Select a DNS server from the list. Prefix Config Select a prefix config option from the list, either WANConnection (prefix will be obtained from the WAN) or Static (enables you to enter the prefix). Interface This field appears if you selected the Wan Connection option for the “prefix config” field.
Draft Configure a G-2426G-A indoor ONT Network configuration Configuring WAN 7368 ISAM ONT Figure 7-14 WAN page 2 Configure the following parameters: Draft Table 7-11 WAN parameters Field Description WAN Connection List Select a WAN connection from the list to set the connection parameters. Connection Type Select a connection type: IPoE or PPPoE. IP mode Select an IP mode from the list: IPv4 or IPv6. Enable/Disable Select this checkbox to enable the WAN connection.
Configure a G-2426G-A indoor ONT Network configuration Configuring WAN DHCP Draft Table 7-11 7368 ISAM ONT WAN parameters (continued) Field Description Service Select the checkboxes to enable service types for this connection. Enable VLAN Select this checkbox to enable VLAN. VLAN ID Enter the VLAN ID. VLAN PRI Enter the VLAN PRI. WAN IP Mode Select an IP mode from the list. Manual DNS Enter the manual Domain Name Server. 3 Click Save. END OF STEPS 7.
Draft Configure a G-2426G-A indoor ONT Network configuration Configuring WAN DHCP 7368 ISAM ONT Figure 7-15 WAN DHCP page 2 Configure the following parameters: Draft Table 7-12 WAN DHCP parameters Field Description WAN Connection List Select a WAN connection from the list. DHCP Option 50 Persistent Select this checkbox to enable DHCP Option 50 persistent. Enable DHCP Option 60 Select this checkbox to enable DHCP Option 60 (vendor class identifier).
Configure a G-2426G-A indoor ONT Network configuration Configuring Wireless 2.4GHz 7368 ISAM ONT Draft 3 Click Save. END OF STEPS 7.19 Configuring Wireless 2.4GHz 1 Click Network→Wireless (2.4GHz) from the left pane in the GPON Home Gateway page. The Wireless (2.4GHz) page displays.
Draft Draft Configure a G-2426G-A indoor ONT Network configuration Configuring Wireless 2.4GHz 7368 ISAM ONT Figure 7-16 Wireless (2.
Configure a G-2426G-A indoor ONT Network configuration Configuring Wireless 2.4GHz 7368 ISAM ONT Draft 2 Configure the following parameters: Table 7-13 Wireless (2.4GHz) parameters Field Description Enable Select this checkbox to enable Wi-Fi. Mode Select a Wi-Fi mode from the list: • auto (b/g/n) • b • g • n • b/g • g/n Bandwidth Select from: • 20 MHz • 40 MHz • 20/40 MHz Channel Select a channel from the list or select Auto to have the channel automatically assigned.
Draft Configure a G-2426G-A indoor ONT Network configuration Configuring Wireless 5GHz 7368 ISAM ONT Table 7-13 Wireless (2.4GHz) parameters (continued) Field Description Encryption Mode Select an encryption mode from the list: • WPA/WPA2 Personal • WPA/WPA2 Enterprise • WEP • OPEN WPA Version Select a WPA version from the list: • WPA2 • WPA/WPA2 WPA Encryption Mode Select a WPA encryption mode from the list: • AES • TKIP/AES WPA Key Enter the WPA key.
Configure a G-2426G-A indoor ONT Network configuration Configuring Wireless 5GHz 7368 ISAM ONT Draft Figure 7-17 Wireless (5GHz) page 2 Configure the following parameters: Draft September 2020 Issue 1 Nokia – Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA 101
Draft Configure a G-2426G-A indoor ONT Network configuration Configuring Wireless 5GHz 7368 ISAM ONT Table 7-14 Wireless (5GHz) parameters Field Description Enable Select this checkbox to enable WiFi. Bandwidth Select from: • 20 MHz • 40 MHz • 80 MHz Channel Select a channel from the list or select Auto to have the channel automatically assigned.
Configure a G-2426G-A indoor ONT Network configuration Configuring wireless scheduling 7368 ISAM ONT Draft Table 7-14 Wireless (5GHz) parameters (continued) Field Description WAN Interface Select a WAN interface from the list Number of IP Select the number of IPs connected to the domain. LAN List Select one or more checkboxes. Notes: 1. When the SSID select, SSID name, password and encryption mode is configured same between 2.4GHz and 5GHz network, the band steering feature is enabled.
Draft Configure a G-2426G-A indoor ONT Network configuration Configuring wireless scheduling 7368 ISAM ONT Figure 7-18 Wireless Schedule page 2 Select the Schedule Function checkbox to turn the wireless signal off for the configured period. 3 Click the plus sign (+) to add a scheduling rule. A separate panel displays for configuring wireless schedule rules. 4 Enter a start time and end time for the period in which you want the wireless signal off.
Configure a G-2426G-A indoor ONT Network configuration Configuring IP routing 7368 ISAM ONT Draft 6 If you select Individual Days, select the checkboxes for the desired days. The Recurrence Pattern shows the rules created to date. 7 If desired, click the plus sign (+) to add more rules. 8 Click Save Changes. END OF STEPS 7.22 Configuring IP routing 1 Click Network→IP Routing from the left pane in the GPON Home Gateway page. The IP Routing page displays.
Draft Configure a G-2426G-A indoor ONT Network configuration Configuring IP routing 7368 ISAM ONT Figure 7-19 IP Routing page 2 Configure the following parameters: Draft Table 7-15 IP Routing network parameters Field Description Enable Routing Select this checkbox to enable routing. Destination IP Address Enter the destination IP address. Destination Netmask Enter the destination network mask. Gateway Enter the gateway address.
Configure a G-2426G-A indoor ONT Network configuration Configuring DNS 7368 ISAM ONT Draft Table 7-15 IP Routing network parameters (continued) Field Description IPv4 Interface Select a WAN connection previously created in the WAN page from the list. Forwarding Policy Select a forwarding policy from the list. 3 Click Add. END OF STEPS 7.23 Configuring DNS 1 Click Network→DNS from the left pane in the GPON Home Gateway page. The DNS page displays.
Draft Configure a G-2426G-A indoor ONT Network configuration Configuring DNS 7368 ISAM ONT Figure 7-20 DNS page 2 Configure the following parameters: Draft Table 7-16 DNS parameters Field Description DNS Proxy Select the Enabled checkbox to enable DNS proxy and click Save. Domain Name Enter the domain name. IPv4 Address Enter the domain IP address and click Add. Origin Domain Enter the origin domain name.
Configure a G-2426G-A indoor ONT Network configuration Configuring TR-069 7368 ISAM ONT Draft Table 7-16 DNS parameters (continued) Field Description New Domain Associate an origin domain with a new domain and click Add. END OF STEPS 7.24 Configuring TR-069 1 Click Network→TR-069 from the left pane in the GPON Home Gateway page. The TR-069 page displays.
Draft Configure a G-2426G-A indoor ONT Network configuration Configuring GRE tunnel 7368 ISAM ONT 2 Configure the following parameters: Table 7-17 TR-069 parameters Field Description Periodic Inform Enable Select this checkbox to enable periodic inform updates. Periodic Inform Interval(s) Enter the time between periodic inform updates, in seconds. URL Enter the URL of the auto-configuration server. Username Enter the username to log in to the auto-configuration server.
Configure a G-2426G-A indoor ONT Network configuration Configuring GRE tunnel 7368 ISAM ONT Draft Figure 7-22 GRE Tunnel page 2 Configure the following parameters: Table 7-18 GRE Tunnel parameters Field Description Tunnel Name Select Create new GRE Tunnel or select an existing tunnel from the list. The tunnel name is automatically assigned by the system. Up to 3 GRE tunnels are supported. WAN Interface Draft September 2020 Issue 1 Select a WAN interface from the list.
Draft Configure a G-2426G-A indoor ONT Network configuration Configuring Upstream (US) Classifier 7368 ISAM ONT Table 7-18 GRE Tunnel parameters (continued) Field Description Primary Remote End Secondary Remote End (optional) Enter an IP address or FQDN that is unique in the system. If the primary remote endpoint is down or unreachable, the secondary remote endpoint becomes active, if configured.
Configure a G-2426G-A indoor ONT Network configuration Configuring Upstream (US) Classifier 7368 ISAM ONT Draft Figure 7-23 US Classifier 2 Select the Policy tab. All classifier policies are displayed in the policy table in the page.
Draft Configure a G-2426G-A indoor ONT Network configuration Configuring Upstream (US) Classifier 7368 ISAM ONT Figure 7-24 US Classifier- Policy page 3 Configure the following parameters: Draft Table 7-19 US Classifier Policy parameters Field Description Tunnel Type The tunnel type is set to GRE and cannot be modified. Tunnel Interface Select a tunnel interface from the list: No Tunnel, GRE Tunnel, or LAN traffic. VLAN ID Enter a VLAN ID (0-4094). VLAN Tag This field is not configurable.
Configure a G-2426G-A indoor ONT Network configuration Configuring Upstream (US) Classifier 7368 ISAM ONT Draft Table 7-19 US Classifier Policy parameters (continued) Field Description IP TOS/DSCP This field is not configurable. All tunnel packets are generated with a default DSCP value (usually 0). Drop Select this checkbox to drop the packets. 4 Click Save. 5 To delete a policy, click Delete for the applicable policy in the policy table.
Draft Configure a G-2426G-A indoor ONT Network configuration Configuring Upstream (US) Classifier 7368 ISAM ONT Figure 7-25 US Classifier- Classifier page 7 Configure the following parameters: At least one field must be selected to create a classifier. A maximum of four fields may be selected to create a classifier; this includes the interface field. Draft Table 7-20 US Classifier parameters Field Description Interface Select an interface from the list; for example, None, LAN, 2.
Configure a G-2426G-A indoor ONT Network configuration Configuring Upstream (US) Classifier 7368 ISAM ONT Draft Table 7-20 US Classifier parameters (continued) Field Description Destination IP Click to enter a destination IP address. Source Port Click to enter a source port. Destination Port Click to enter a destination port. Protocol Click to enter a protocol. Priority Select a priority level from 1 to 8. The lower the number, the higher the priority.
Draft Configure a G-2426G-A indoor ONT Network configuration Configuring Upstream (US) Classifier 7368 ISAM ONT Figure 7-26 US Classifier Rules page 11 Configure the classifier rule. Draft Table 7-21 US Classifier Rules parameters Field Description Policy Select a policy from the list. Classifier Select a classifier from the list. Interface Select an interface from the list; for example, None, LAN, 2.4G SSID, 5G SSID. Source MAC Enter a source MAC address.
Configure a G-2426G-A indoor ONT Network configuration Configuring QoS 7368 ISAM ONT Draft Table 7-21 US Classifier Rules parameters (continued) Field Description Source IP Enter a source IP address. Destination IP Enter a destination IP address. Source Port Enter a source port address. Destination Port Enter a destination port address. IP Protocol Type Enter a value between 0 and 254. 12 Click Save.
Draft Draft Configure a G-2426G-A indoor ONT Network configuration Configuring QoS 7368 ISAM ONT Figure 7-27 QoS Config page (L2 packet sizes) Nokia – Proprietary and Confidential Use pursuant to applicable agreements 120 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1
Configure a G-2426G-A indoor ONT Network configuration Configuring QoS 7368 ISAM ONT Draft Figure 7-28 QoS Config page (L3 packet sizes) Draft September 2020 Issue 1 Nokia – Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA 121
Draft Configure a G-2426G-A indoor ONT Network configuration Configuring QoS 7368 ISAM ONT 2 Configure the following parameters: Table 7-22 QoS Config parameters Field Description QoS Setting Type Select a QoS service layer type from the list: L2 or L3. Classification Criteria Source MAC Enter the source MAC Select the Exclude checkbox to exclude the source MAC address. Interface Select an interface from the list.
Configure a G-2426G-A indoor ONT Security configuration Overview 7368 ISAM ONT Draft Security configuration 7.28 7.28.1 Overview Purpose This chapter describes the security configuration tasks supported by G-2426G-A ONTs 7.28.2 Contents 7.28 Overview 123 7.29 Configuring the firewall 123 7.30 Configuring the MAC filter 124 7.31 Configuring the IP filter 126 7.32 Configuring the URL filter 128 7.33 Configuring parental control 129 7.34 Configuring DMZ and ALG 131 7.
Draft Configure a G-2426G-A indoor ONT Security configuration Configuring the MAC filter 7368 ISAM ONT 2 Configure the following parameters: Table 7-23 Firewall parameters Field Description Security level Select the security level from the list: High: Traffic denied inbound and minimally permit common services outbound Low: All outbound traffic and pinhole-defined inbound traffic is allowed Off: All inbound and outbound traffic is allowed Attack Protect (Protection against DoS or DDoS attacks) Selec
Configure a G-2426G-A indoor ONT Security configuration Configuring the MAC filter 7368 ISAM ONT Draft Figure 7-30 MAC Filter page Draft September 2020 Issue 1 Nokia – Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA 125
Draft Configure a G-2426G-A indoor ONT Security configuration Configuring the IP filter 7368 ISAM ONT 2 Configure the following parameters: Table 7-24 MAC Filter parameters Field Description Ethernet Interface MAC Filter Mode Select the MAC filter mode from the list: Blocked or Allowed. LAN Port Enter the LAN port range. MAC Address Select the MAC address from the list or enter the address in the text field.
Configure a G-2426G-A indoor ONT Security configuration Configuring the IP filter 7368 ISAM ONT Draft Figure 7-31 IP Filter page 2 Configure the following parameters: Table 7-25 IP Filter parameters Field Description Enable IP Filter Select this checkbox to enable an IP filter.
Draft Configure a G-2426G-A indoor ONT Security configuration Configuring the URL filter 7368 ISAM ONT Table 7-25 IP Filter parameters (continued) Field Description Remote IP Address Enter the remote IP address. Destination Subnet Mask Enter the destination subnet mask. Protocol Select an application protocol or ALL from the list. 3 Click Add. END OF STEPS 7.32 Configuring the URL filter 1 Click Security→URL Filter from the left pane in the GPON Home Gateway page. The URL Filter page displays.
Configure a G-2426G-A indoor ONT Security configuration Configuring parental control 7368 ISAM ONT Draft 2 Configure the following parameters: Table 7-26 URL Filter parameters Field Description Enable URL filter Select the checkbox to enable the URL filter. URL filter type Select the option to block the URL or allow the URL. URL List URL Address Enter the URL address. Port - default to 80 Enter the port number; the default is 80. Note: You cannot use URL filtering for HTTPS.
Draft Configure a G-2426G-A indoor ONT Security configuration Configuring parental control 7368 ISAM ONT Figure 7-33 Parental Control page 2 Select the Access Control checkbox. 3 Click the plus sign (+) to add a policy. A separate panel displays for configuring the policy name, IP address of the device, and dates and times for the policy. 4 Configure the following parameters: Table 7-27 Parental Control parameters Field Description Access Control Select this checkbox to enable access control.
Configure a G-2426G-A indoor ONT Security configuration Configuring DMZ and ALG 7368 ISAM ONT Draft Table 7-27 Parental Control parameters (continued) Field Description Policy Name Enter a name for the parental control policy or select a policy from the list. MAC Address Enter the MAC address or select a MAC address from the list. IPv4 Address Enter the IPv4 address for the device or select an IPv4 address from the list. Url Port Enter the URL port for the device.
Draft Configure a G-2426G-A indoor ONT Security configuration Configuring DMZ and ALG 7368 ISAM ONT Figure 7-34 DMZ and ALG page 2 Configure the following parameters: Table 7-28 ALG parameters Field Description ALG Config Select the checkboxes to enable the protocols to be supported by the ALG: FTP, TFTP, SIP, H323, RTSP, L2TP, IPSEC, PPTP. DMZ Config WAN Connection List Select a WAN connection from the list. Enable DMZ Select this checkbox to enable DMZ on the chosen WAN connection.
Configure a G-2426G-A indoor ONT Security configuration Configuring access control 7368 ISAM ONT Draft 4 Configure the following parameters: Table 7-29 DMZ parameters Field Description ALG Config Select the checkboxes to enable the protocols to be supported by the ALG: FTP, TFTP, SIP, H323, RTSP, L2TP, IPSEC, PPTP. DMZ Config WAN Connection List Select a WAN connection from the list. Enable DMZ Select this checkbox to enable DMZ on the chosen WAN connection.
Draft Configure a G-2426G-A indoor ONT Security configuration Configuring access control 7368 ISAM ONT Figure 7-35 Access Control page 2 Configure the following parameters: Draft Table 7-30 Access Control parameters Field Description WAN Select a connection from the list. Trusted Network Enable Click to enable or disable trusted network.
Configure a G-2426G-A indoor ONT Security configuration Configuring access control 7368 ISAM ONT Draft Table 7-30 Access Control parameters (continued) Field Description ICMP, Telnet, SSH, HTTP, TR-069, HTTPS, SFTP Select an access control level for each protocol: WAN side: Allow, Deny, or Trusted Network Only LAN side: Allow or Deny 3 Click Save. 4 Optionally, add one or more subnet trusted networks. The maximum number of entries is 32.
Draft Configure a G-2426G-A indoor ONT Configuring the Application Overview 7368 ISAM ONT Configuring the Application 7.36 7.36.1 Overview Purpose This chapter describes the application configuration tasks supported by the G-2426G-A ONTs. 7.36.2 Contents 7.36 Overview 136 7.37 Configuring port forwarding 136 7.38 Configuring port triggering 138 7.39 Configuring DDNS 140 7.40 Configuring NTP 142 7.41 Configuring USB 143 7.42 Configuring UPnP and DLNA 145 7.43 Configuring voice 146 7.
Configure a G-2426G-A indoor ONT Configuring the Application Configuring port forwarding 7368 ISAM ONT Draft Figure 7-36 Port Forwarding page 2 Configure the following parameters: Table 7-32 Port Forwarding parameters Field Description Application Name Select an application name from the list The default is Custom settings. WAN Port Enter the WAN port range. LAN Port Enter the LAN port range. Internal Client Select a connected device from the list and enter the associated IP address.
Draft Configure a G-2426G-A indoor ONT Configuring the Application Configuring port triggering 7368 ISAM ONT Table 7-32 Port Forwarding parameters (continued) Field Description Enable Mapping Select this checkbox to enable mapping. WAN Connection List Select a WAN connection from the list. Note: Only active devices are shown on this list. 3 Click Add. END OF STEPS 7.38 Configuring port triggering 1 Draft Click Application→Port Triggering from the left pane in the GPON Home Gateway page.
Configure a G-2426G-A indoor ONT Configuring the Application Configuring port triggering 7368 ISAM ONT Draft Figure 7-37 Port Triggering page 2 Configure the following parameters: Table 7-33 Port Triggering parameters Field Application Name Description Select an application name from the list. The default is Custom settings. Open Port Enter the open port range. Triggering Port Enter the triggering port range. Expire Time Enter the expiration time in seconds.
Draft Configure a G-2426G-A indoor ONT Configuring the Application Configuring DDNS 7368 ISAM ONT Table 7-33 Port Triggering parameters (continued) Field Description Open Protocol Select the open port protocol from the list: • TCP • UDP • TCP/UDP Trigger Protocol Select the triggering port protocol from the list: • TCP • UDP • TCP/UDP Enable Triggering Select this checkbox to enable port triggering. WAN Connection List Select a WAN connection from the list.
Configure a G-2426G-A indoor ONT Configuring the Application Configuring DDNS 7368 ISAM ONT Draft Figure 7-38 DDNS page 2 Configure the following parameters: Table 7-34 DDNS parameters Field Description WAN Connection List Select a WAN connection from the list. Enable DDNS Select this checkbox to enable DDNS on the chosen WAN connection. ISP Select an ISP from the list. Domain Name Enter the domain name. Username Enter the username. Password Enter the password.
Draft Configure a G-2426G-A indoor ONT Configuring the Application Configuring NTP 7368 ISAM ONT 3 Click Save. END OF STEPS 7.40 Configuring NTP 1 Click Application→NTP from the left pane in the GPON Home Gateway page. The NTP page displays.
Configure a G-2426G-A indoor ONT Configuring the Application Configuring USB 7368 ISAM ONT Draft Table 7-35 NTP parameters Field Description Enable NTP Service Select this checkbox to enable the NTP service. Current Time Enter the current local date and time. Primary Time Server Select a time server from the list or choose Customer setting and enter the address of the time server.
Draft Configure a G-2426G-A indoor ONT Configuring the Application Configuring USB 7368 ISAM ONT Figure 7-40 USB page 2 Configure the following parameters: Draft Table 7-36 USB parameters Field Description Enable FTP server Select this checkbox to enable using an FTP server Nokia – Proprietary and Confidential Use pursuant to applicable agreements 144 3FE-XXXXX-AAAA-TCZZA September 2020 Issue 1
Configure a G-2426G-A indoor ONT Configuring the Application Configuring UPnP and DLNA 7368 ISAM ONT Draft Table 7-36 USB parameters (continued) Field Description Username Enter the username for the FTP server. Password Enter the password for the FTP server. Re-enter Password Enter the password for the FTP server. Enable SFTP server Select this checkbox to enable using an SFTP server. Enable SFTP for Remote Access Select this checkbox to enable SFTP for remote access.
Draft Configure a G-2426G-A indoor ONT Configuring the Application Configuring voice 7368 ISAM ONT Figure 7-41 UPnP and DLNA page 2 Select the Enable UPnP/DLNA checkbox to enable UPnP/DLNA. 3 Click Save/Apply. END OF STEPS 7.43 Configuring voice 1 Draft Click Application→Voice Setting from the left pane in the GPON Home Gateway page. The Voice Setting page displays.
Configure a G-2426G-A indoor ONT Configuring the Application Configuring voice 7368 ISAM ONT Draft Figure 7-42 Voice Setting page Draft September 2020 Issue 1 Nokia – Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA 147
Draft Configure a G-2426G-A indoor ONT Configuring the Application Configuring voice 7368 ISAM ONT 2 Configure the following parameters: Table 7-37 Voice Setting parameters Field Description Voice Setting Outbound Proxy Enter the SIP outbound proxy. Outbound Proxy Port Enter the outbound proxy port. Proxy Server Enter the proxy server. Proxy Server Port Enter the proxy server port. Registrar Server Enter the registrar server. Registrar Server Port Enter the registrar server port.
Configure a G-2426G-A indoor ONT Maintenance Overview 7368 ISAM ONT Draft Maintenance 7.44 7.44.1 Overview Purpose This chapter describes the maintenance tasks supported by G-2426G-A ONTs. 7.44.2 Contents 7.44 Overview 149 7.45 Configuring the password 149 7.46 WAN speed test 151 7.47 Speed test history 152 7.48 Configuring LOID 154 7.49 Configuring SLID 155 7.50 Managing the device 156 7.51 Backing up the configuration 158 7.52 Restoring the configuration 159 7.
Draft Configure a G-2426G-A indoor ONT Maintenance Configuring the password 7368 ISAM ONT When the password does not meet the password rules, the application displays a message to indicate which password rule has not been followed, for example: • the password is too short • the password is too long • the first character cannot be a special character • there are not enough character classes 1 Click Maintenance→Password from the left pane in the GPON Home Gateway page. The Password page displays.
Configure a G-2426G-A indoor ONT Maintenance WAN speed test 7368 ISAM ONT Draft Table 7-38 Password parameters Field Description Original Password Enter the current password. New Password Enter the new password (must adhere to the password rules described above). Re-enter password Re-enter the new password (Must match the new password entered above exactly). Prompt message Enter the password prompt message. 3 Click Save. END OF STEPS 7.
Draft Configure a G-2426G-A indoor ONT Maintenance Speed test history 7368 ISAM ONT 2 Accept Ookla Privacy Policy as instructed in the Note displayed. Click Start to start the speed test. You can click Cancel to cancel the speed test. END OF STEPS 7.47 Speed test history 1 Draft Click Maintenance→Speed Test History from the left pane in the GPON Home Gateway page. The Speed History page displays.
Configure a G-2426G-A indoor ONT Maintenance Speed test history 7368 ISAM ONT Draft Figure 7-44 Speed Test History Draft September 2020 Issue 1 Nokia – Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA 153
Draft Configure a G-2426G-A indoor ONT Maintenance Configuring LOID 7368 ISAM ONT The history of speed test is displayed. You can click Refresh to display up-to-date information. END OF STEPS The history of the speed test is displayed. 7.48 Configuring LOID 1 Click Maintenance→LOID Configuration from the left pane in the GPON Home Gateway page. The LOID Configuration page displays.
Configure a G-2426G-A indoor ONT Maintenance Configuring SLID 7368 ISAM ONT Draft Table 7-39 LOID Configuration parameters Field Description LOID Enter the LOID; the maximum number of characters is 24. If the password is null, this field may be left blank Password Enter the password; the maximum number of characters is 12. 3 Click Save/Apply. END OF STEPS 7.49 Configuring SLID 1 Click Maintenance→SLID Configuration from the left pane in the GPON Home Gateway page.
Draft Configure a G-2426G-A indoor ONT Maintenance Managing the device 7368 ISAM ONT 2 Configure the following parameters: Table 7-40 SLID Configuration parameters Field Description Current SLID Displays the current SLID. Enter New SLID Enter the new SLID. SLID Mode Select a SLID mode from the list. The default is HEX Mode. 3 Click Save. END OF STEPS 7.50 Managing the device 1 Draft Click Maintenance→Device Management from the left pane in the GPON Home Gateway page.
Configure a G-2426G-A indoor ONT Maintenance Managing the device 7368 ISAM ONT Draft Figure 7-47 Device Management page 2 Configure the following parameters: Table 7-41 Device Management parameters Field Description Host Name Select a hostname from the list. Host Alias Enter an alias for the selected host. 3 Click Add.
Draft Configure a G-2426G-A indoor ONT Maintenance Backing up the configuration 7.51 7368 ISAM ONT Backing up the configuration 1 Click Maintenance→Backup and Restore from the left pane in the GPON Home Gateway page. The Backup and Restore page displays. Figure 7-48 Backup and Restore page 2 Click Export to export the current ONT configuration to a backup file.
Configure a G-2426G-A indoor ONT Maintenance Restoring the configuration Draft 7.52 7368 ISAM ONT Restoring the configuration 1 Click Maintenance→Backup and Restore from the left pane in the GPON Home Gateway page. The Backup and Restore page displays. Figure 7-49 Backup and Restore page 2 Click Choose file and select a backup file. 3 Click Import to restore the ONT to the saved backup.
Draft Configure a G-2426G-A indoor ONT Maintenance Upgrading firmware 7.53 7368 ISAM ONT Upgrading firmware 1 Click Maintenance→Firmware Upgrade from the left pane in the GPON Home Gateway page. The Firmware Upgrade page displays. Figure 7-50 Firmware Upgrade page 2 Click Choose file and select the firmware file. 3 Click Upgrade to upgrade the firmware.
Configure a G-2426G-A indoor ONT Maintenance Rebooting the device Draft 7.54 7368 ISAM ONT Rebooting the device 1 Click Maintenance→Reboot Device from the left pane in the GPON Home Gateway page. The Reboot Device page displays. Figure 7-51 Reboot Device page 2 Click Reboot to reboot the ONT.
Draft Configure a G-2426G-A indoor ONT Maintenance Resetting to factory defaults 7.55 7368 ISAM ONT Resetting to factory defaults 1 Click Maintenance→Factory Default from the left pane in the GPON Home Gateway page. The Factory Default page displays. Figure 7-52 Factory Default page 2 Click Factory Default to reset the ONT to its factory default settings.
Configure a G-2426G-A indoor ONT Maintenance Diagnosing WAN connections Draft 7.56 7368 ISAM ONT Diagnosing WAN connections 1 Click Maintenance→Diagnostics from the left pane in the GPON Home Gateway page. The Diagnostics page displays. Figure 7-53 Diagnostics page 2 Select a WAN connection to diagnose from the list. 3 Enter the IP address or domain name.
Draft Configure a G-2426G-A indoor ONT Maintenance Viewing log files 7368 ISAM ONT 4 Select the test type: ping, traceroute, or both. 5 Enter the number of ping attempts to perform (1 - 1000); the default is 4. 6 Enter a ping packet length (64-1024); the default is 64. 7 Enter the maximum number of trace hops (1-255); the default is 30. 8 Click Start Test. The results will be displayed at the bottom of the page. 9 Click Cancel to cancel the test. END OF STEPS 7.
Configure a G-2426G-A indoor ONT Maintenance Viewing log files 7368 ISAM ONT Draft Figure 7-54 Log page 2 Select a write level from the list to determine which types of events are recorded in the log file: • Emergency • Alert • Critical • Error • Warning • Notice • Informational • Debug Draft September 2020 Issue 1 Nokia – Proprietary and Confidential Use pursuant to applicable agreements 3FE-XXXXX-AAAA-TCZZA 165
Draft Configure a G-2426G-A indoor ONT Maintenance Viewing log files 7368 ISAM ONT 3 Select a reading level from the list to determine which types of events to display from the log file: • Emergency • Alert • Critical • Error • Warning • Notice • Informational • Debug The log file is displayed at the bottom of the page.
Configure a G-2426G-A indoor ONT RG Troubleshooting Counters Overview 7368 ISAM ONT Draft RG Troubleshooting Counters 7.58 7.58.1 Overview Purpose This section describes the RG troubleshooting counters GUI procedures. 7.58.2 7.59 Contents 7.58 Overview 167 7.
Draft Configure a G-2426G-A indoor ONT RG Troubleshooting Counters Viewing Residential Gateway (RG) troubleshooting counters 7368 ISAM ONT 2 Configure the following parameters: Table 7-42 RG Troubleshooting Counters parameters Field Description WAN Connection List Select a WAN connection from the list. US Throughput This test is used to determine the upstream throughput/speed. Click US Speed Test to specify the time for the upstream test. The default is weekly, performed at idle to a public server.
7368 ISAM ONT Draft Configure a G-2426G-A indoor ONT RG Troubleshooting Counters Viewing Residential Gateway (RG) troubleshooting counters Table 7-42 RG Troubleshooting Counters parameters (continued) Field Description DS Packet Loss Indicates the number of downstream packages lost. Internet Status Indicates whether the broadband connections is active (UP) or not (DOWN).
Draft Draft Configure a G-2426G-A indoor ONT RG Troubleshooting Counters Viewing Residential Gateway (RG) troubleshooting counters Nokia – Proprietary and Confidential Use pursuant to applicable agreements 170 3FE-XXXXX-AAAA-TCZZA 7368 ISAM ONT September 2020 Issue 1
ONT configuration file over OMCI Overview 7368 ISAM ONT Draft 8 ONT configuration file over OMCI 8.1 Overview 8.1.1 Purpose 8.1.2 Contents 8.1 Overview 171 8.2 Purpose 171 8.3 Supported configuration file types 171 8.4 ONT configuration file over OMCI 174 8.2 Purpose This procedure describes how to use configuration files over OMCI to configure ONTs.
Draft ONT configuration file over OMCI Supported configuration file types 7368 ISAM ONT Table 8-1 Supported configuration files File Index Description Details Supported ONTs/DPU PRE ONT pre-configuration file The XML-based PRECONFIG file controls the working mechanics of the ONT for various services. The default behavior of different ONTs may vary based on the factory settings. The pre-configuration file includes the factory default value for the residential gateway.
ONT configuration file over OMCI Supported configuration file types 7368 ISAM ONT Draft Table 8-1 Supported configuration files (continued) File Index Description Details Supported ONTs/DPU GFT G.fast-related configuration file This text-based json script file controls the default behavior of the G.Fast ONT. Nokia G.fast. This file includes the provisioning parameters of the G.fast transports layer; it does not include VLAN or QoS provisioning.
Draft ONT configuration file over OMCI ONT configuration file over OMCI 7368 ISAM ONT Table 8-2 Download configuration files (continued) ONT type Legacy method download MTK(eg.G240WF) 8.4 Zero management download PRE file CFG file PRE file CFG file — ✓ ✓ ✓ ONT configuration file over OMCI WARNING Equipment Damage Executing the following procedure will trigger the ONT to reboot, which will impact ongoing services.
ONT configuration file over OMCI ONT configuration file over OMCI 7368 ISAM ONT Draft e. Configure equipment interface pland-cfgfile1=XMLXXXXXX1 and dnload-cfgfile1 XMLXXXXXX1 Configure equipment interface pland-cfgfile2=XMLXXXXXX2 and dnload-cfgfile2 XMLXXXXXX2 Although the OLT permits the above two steps without reporting an error, Nokia does not recommend executing them, because the ONT may exhibit unexpected behavior. f.
Draft ONT configuration file over OMCI ONT configuration file over OMCI 7368 ISAM ONT and FX NT, or the 7342 ISAM FTTU Operation and Maintenance Using TL1 and CLI. Please note: • pri-cfgfile-pland/dnload or sec-cfgfile-pland/dnload can be 1 to 14 characters. • pri-cfgfile-pland and pri-cfgfile-dnload should be the same name. Examples Note: X can be 1 or 2 unless specified: a. If pland-cfgfileX= Disabled and dnload-cfgfileX= Disabled , no file will be downloaded to the ONT. b.