Product Guide

ManualsBrandsNokia Shanghai Bell ManualsElectronics7368 ISAM ONT

7368 ISAM ONT G-240W-J Product Guide

7368 Intelligent Services Access

Manager ONT

7368 ISAM ONT G-240W-J Product Guide

3FE-48009-AAAA-TCZZA

Issue: 01

Summary of content (168 pages)

PAGE 1
7368 ISAM ONT G-240W-J Product Guide 7368 Intelligent Services Access Manager ONT 7368 ISAM ONT G-240W-J Product Guide 3FE-48009-AAAA-TCZZA Issue: 01
PAGE 2
7368 ISAM ONT G-240W-J Product Guide Nokia — Proprietary and confidential Use pursuant to applicable agreements Nokia is a registered trademark of Nokia Corporation. Other products and company names mentioned herein may be trademarks or tradenames of their respective owners. The information presented is subject to change without notice. No responsibility is assumed for inaccuracies contained herein. © 2019 Nokia.
PAGE 3
7368 ISAM ONT G-240W-J Product Guide Preface 1 Preface This preface provides general information about the documentation set for optical network terminals (ONTs). 1.1 Scope This documentation set provides information about safety, features and functionality, ordering, hardware installation and maintenance, and software installation procedures for the current release. 1.
PAGE 4
Preface 7368 ISAM ONT G-240W-J Product Guide 1.6 Nokia quality processes Nokia’s ONT quality practices are in compliance with TL 9000 requirements. These requirements are documented in the Fixed Networks Quality Manual 3FQ-30146-6000-QRZZA. The quality practices adequately ensure that technical requirements and customer end-point requirements are met. The customer or its representatives may be allowed to perform on-site quality surveillance audits, as agreed upon during contract negotiations 1.
PAGE 5
7368 ISAM ONT G-240W-J Product Guide Preface Individual PDFs of customer documents are also accessible through the Nokia Customer Support website. 1 Navigate to http://support.alcatel-lucent.com and enter your user name and password. If you are a new user and require access to this service, please contact your Nokia sales representative. 2 From the Technical Content for drop-down menu, choose the product. 3 Click on Manuals and Guides to display a list of customer documents by title and part number.
PAGE 6
Preface 7368 ISAM ONT G-240W-J Product Guide Note — A note provides information that is, or may be, of special interest. 1.9.1 Procedures with options or substeps When there are options in a procedure, they are identified by letters. When there are required substeps in a procedure, they are identified by roman numerals. Procedure 3 Example of options in a procedure At step 1, you can choose option a or b. At step 1, you must do what the step indicates.
PAGE 7
368 ISAM ONT G-240W-J Product Guide Preface 1.10 Multiple PDF document search You can use Adobe Reader Release 6.0 and later to search multiple PDF files for a common term. Adobe Reader displays the results in a single display panel. The results are grouped by PDF file, and you can expand the entry for each file. Note — The PDF files in which you search must be in the same folder. Procedure 5 To search multiple PDF files for a common term 1 Open Adobe Acrobat Reader.
PAGE 8
7368 ISAM ONT G-240W-J Product Guide Table of contents 1 Preface............................................................................................................... 3 1.1 Scope............................................................................................................................... 3 1.2 Audience .......................................................................................................................... 3 1.3 Required knowledge .................................
PAGE 9
7368 ISAM ONT G-240W-J Product Guide 3.4 ESD safety guidelines ................................................................................................... 26 3.5 Laser safety guidelines .................................................................................................. 26 3.5.1 Laser classification ..................................................................................................... 27 3.5.1.1 Laser warning labels ......................................................
PAGE 10
7368 ISAM ONT G-240W-J Product Guide 5.2.10 Mobile offload support .............................................................................................. 46 5.2.11 Support for soft GRE tunnels .................................................................................... 46 5.2.11.1 GRE ....................................................................................................................... 46 5.2.11.2 Soft GRE ....................................................................
PAGE 11
7368 ISAM ONT G-240W-J Product Guide 8.2.6 Maintenance ............................................................................................................. 144 8.2.7 RG troubleshooting counters .................................................................................... 159 9 ONT configuration file over OMCI ................................................................ 162 9.1 Purpose ......................................................................................................
PAGE 12
7368 ISAM ONT G-240W-J Product Guide List of figures 12 2 ANSI CPE safety guidelines.........................................................17 Figure 1 Sample safety label...................................................................................19 3 ETSI ONT safety guidelines.........................................................23 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 PSE certification........................................................................................
PAGE 13
7368 ISAM ONT G-240W-J Product Guide Figure 35 Figure 36 Figure 37 Figure 38 Figure 39 Figure 40 Figure 41 Figure 42 Figure 43 Figure 44 Figure 45 Figure 46 Figure 47 Figure 48 Figure 49 Figure 50 Figure 51 Figure 52 Figure 53 Figure 54 Figure 55 Figure 56 Figure 57 Figure 58 Figure 59 Figure 60 Figure 61 Figure 62 Figure 63 Figure 64 Figure 65 Figure 66 Figure 67 Figure 68 Figure 69 Figure 70 Figure 71 Figure 72 Figure 73 Figure 74 WiFi 2.4G network window.................................................
PAGE 14
7368 ISAM ONT G-240W-J Product Guide Table 2 Safety labels..............................................................................................24 5 G-240W-J unit data sheet.............................................................39 Table 3 Table 4 Table 5 Table 6 Table 7 Table 8 Table 9 Table 10 Table 11 Table 12 Table 13 Table 14 Table 15 Table 17 Identification of G-240W-J indoor ONTs....................................................39 G-240W-J power supply...........................
PAGE 15
7368 ISAM ONT G-240W-J Product Guide Issue: 01 Table 42 Table 43 Table 44 Table 45 Table 46 Table 47 Table 48 Table 49 Table 50 Table 51 Table 52 Table 53 Table 54 Table 55 Table 56 Table 57 URL Filter parameters.............................................................................126 Parental control parameters....................................................................129 DMZ and ALG parameters ......................................................................
PAGE 16
ANSI CPE safety guidelines 7368 ISAM ONT G-240W-J Product Guide 2 ANSI CPE safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of devices in the North American or ANSI market. 2.1 Safety instructions This section describes the safety instructions that are provided in the CPE customer documentation and on the equipment. 2.1.
PAGE 17
7368 ISAM ONT G-240W-J Product Guide ANSI CPE safety guidelines Do not proceed beyond a warning until the indicated conditions are fully understood and met. The following is an example of the Caution box. Caution 1 — Possibility of service interruption. Caution 2 — Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met.
PAGE 18
ANSI CPE safety guidelines 7368 ISAM ONT G-240W-J Product Guide 2.2 Safety standards compliance This section describes the CPE compliance with North American safety standards. Warning — Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2.2.
PAGE 19
7368 ISAM ONT G-240W-J Product Guide ANSI CPE safety guidelines together with Commission Regulation (EC) No 1275/2008 and Commission Regulation (EC) No 801/2013. The G-240W-J devices qualify as high network availability (HiNA) equipment. Since the main purpose of G-240W-J devices is to provide network functionality with HiNA 7 days/24 hours, the modes Off/Standby, Power Management, and Networked Standby are inappropriate.
PAGE 20
ANSI CPE safety guidelines 7368 ISAM ONT G-240W-J Product Guide in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the nocollocation statement. This device complies with Part 15 of the FCC Rules.
PAGE 21
7368 ISAM ONT G-240W-J Product Guide 2.3.1 ANSI CPE safety guidelines Power supplies The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property. 2.3.2 Cabling The following are the guidelines regarding cables used for the customer premises equipment: • Use only cables approved by the relevant national electrical code.
PAGE 22
ETSI ONT safety guidelines 7368 ISAM ONT G-240W-J Product Guide 3 ETSI ONT safety guidelines This chapter provides information about the mandatory regulations that govern the installation and operation of the optical network terminals (ONTs). 3.1 Safety instructions This section describes the safety instructions that are provided in the ONT customer documentation and on the equipment. 3.1.1 Safety instruction boxes The safety instruction boxes are provided in the ONT customer documentation.
PAGE 23
7368 ISAM ONT G-240W-J Product Guide ETSI ONT safety guidelines The following is an example of the Caution box. Caution 1 — Possibility of service interruption. Caution 2 — Service interruption. The Caution box indicates that the described activity or situation may, or will, cause service interruption. Do not proceed beyond a caution until the indicated conditions are fully understood and met. The following is an example of the Note box. Note — Information of special interest.
PAGE 24
ETSI ONT safety guidelines 7368 ISAM ONT G-240W-J Product Guide 19841 3.2 Safety standards compliance This section describes the ONT compliance with the European safety standards. 3.2.1 EMC, EMI, and ESD compliance The ONT equipment complies with the following EMC, EMI, and ESD requirements: • EN 300-328 v1.9.1 wide band data transmission standards for 2.4GHz bands • EN 300-386 V1.5.1: Electromagnetic Compatibility and Radio Spectrum Matters • • • • • 3.2.
PAGE 25
7368 ISAM ONT G-240W-J Product Guide 3.2.4 ETSI ONT safety guidelines CE RED RF Radiation Exposure Statement This device complies with CE RED radiation exposure limits set forth for an uncontrolled environment. To comply with CE RED RF exposure compliance requirements, this grant is applicable only for mobile configurations.
PAGE 26
ETSI ONT safety guidelines 3.3.1 7368 ISAM ONT G-240W-J Product Guide Power supplies The use of any non-Nokia approved power supplies or power adapters is not supported or endorsed by Nokia. Such use will void any warranty or support contract with Nokia. Such use greatly increases the danger of damage to equipment or property. 3.3.2 Cabling The following are the guidelines regarding cables used for the ONT equipment: • All cables must be approved by the relevant national electrical code.
PAGE 27
7368 ISAM ONT G-240W-J Product Guide ETSI ONT safety guidelines Only qualified service personnel who are extremely familiar with laser radiation hazards should install or remove the fiber optic cables and units in this system. Danger — There may be invisible laser radiation at the fiber optic cable when the cable is removed from the connector. Avoid direct exposure to the laser beam. Observe the following danger for laser hazard. Eyes can be damaged when they are exposed to a laser beam.
PAGE 28
ETSI ONT safety guidelines Figure 4 7368 ISAM ONT G-240W-J Product Guide Laser classification label CLASS 1 LASER PRODUCT PRODUCTO LASER CLASE 1 CLASE 1 DEL LASER LASER CLASSE 1 18992 Figure 5 shows a laser warning label and an explanatory label for laser products. Labels and warning may be provided in other languages.
PAGE 29
7368 ISAM ONT G-240W-J Product Guide ETSI ONT safety guidelines CLASS 1 LASER PRODUCT RAYONNEMENT LASER CLASSE 1 RAYONNEMENT LASER INVISIBLE EVITER TOUTE EXPOSITION AU FAISCEAU NE PAS DEMONTER. FAIRE APPEL A UN PERSONNELL QUALIFIE CLASE 1 DEL LASER RADIACION DE LASER INVISIBLE. EVITAR CUALOUIER EXPOSICION AL RAYO LASER. NO DESMONTAR. LLAMAR A PERSONAL AUTORIZADO INVISIBLE LASER RADIATION PRESENT AT FIBER OPTIC CABLE WHEN NOT CONNECTED. AVOID DIRECT EXPOSURE TO BEAM. Laser Warning Label 18993 3.5.
PAGE 30
ETSI ONT safety guidelines 3.5.3 7368 ISAM ONT G-240W-J Product Guide Transmit optical output The maximum transmit optical output of an ONT is +5 dBm. 3.5.4 Normal laser operation In normal operation, fiber cable laser radiation is always off until it receives signal from the line terminal card. Eyes can be damaged when they exposed to a laser beam. Operating personnel must observe the instructions on the laser explanatory label before plugging in the optical module.
PAGE 31
7368 ISAM ONT G-240W-J Product Guide ETSI environmental and CRoHS guidelines 4 ETSI environmental and CRoHS guidelines This chapter provides information about the ETSI environmental China Restriction of Hazardous Substances (CRoHS) regulations that govern the installation and operation of the optical line termination (OLT) and optical network termination (ONT) systems. This chapter also includes environmental operation parameters of general interest. 4.
PAGE 32
ETSI environmental and CRoHS guidelines 7368 ISAM ONT G-240W-J Product Guide Concentration Limits for Certain Hazardous Substances in Electronic Information Products). Products with this label are recyclable. The label may be found in this documentation or on the product. Figure 7 Products below MCV value label 18986 4.1.2.
PAGE 33
7368 ISAM ONT G-240W-J Product Guide Figure 8 ETSI environmental and CRoHS guidelines Products above MCV value label Together with major international telecommunications equipment companies, Nokia has determined it is appropriate to use an EFUP of 50 years for network infrastructure equipment and an EFUP of 20 years for handsets and accessories.
PAGE 34
ETSI environmental and CRoHS guidelines 4.3.1 7368 ISAM ONT G-240W-J Product Guide ONT environmental requirements See the ONT technical specification documentation for more information about temperature ranges. 4.3.2 Storage According to ETS 300-019-1-1 - Class 1.1, storage of OLT equipment must be in Class 1.1, weather-protected, temperature-controlled locations. 4.3.3 Transportation According to EN 300-019-1-2 - Class 2.
PAGE 35
7368 ISAM ONT G-240W-J Product Guide 4.3.6 ETSI environmental and CRoHS guidelines Material content compliance European Union (EU) Directive 2002/95/EC, “Restriction of the use of certain Hazardous Substances” (RoHS), restricts the use of lead, mercury, cadmium, hexavalent chromium, and certain flame retardants in electrical and electronic equipment.
PAGE 36
ETSI environmental and CRoHS guidelines 7368 ISAM ONT G-240W-J Product Guide At the end of their life, the OLT and ONT products are subject to the applicable local legislations that implement the European Directive 2012/19EU on waste electrical and electronic equipment (WEEE). There can be different requirements for collection and treatment in different member states of the European Union.
PAGE 37
7368 ISAM ONT G-240W-J Product Guide G-240W-J unit data sheet 5 G-240W-J unit data sheet 5.1 G-240W-J part numbers and identification 5.2 G-240W-J general description 5.3 G-240W-J software and installation feature support 5.4 G-240W-J interfaces and interface capacity 5.5 G-240W-J LEDs 5.6 G-240W-J detailed specifications 5.7 G-240W-J GEM ports and T-CONTs 5.8 G-240W-J performance monitoring statistics 5.9 G-240W-J functional blocks 5.10 G-240W-J standards compliance 5.
PAGE 38
G-240W-J unit data sheet 7368 ISAM ONT G-240W-J Product Guide Table 4 provides the power supply information for the G-240W-J ONT. For more information on power supplies, see the 7368 ISAM ONT Power Supply and UPS Guide. Table 4 5.
PAGE 39
7368 ISAM ONT G-240W-J Product Guide • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Issue: 01 G-240W-J unit data sheet Internal DHCP server, with configurable DHCP pool and gateway WPS on wireless authorization support 802.11ac support 2.4 GHz and 5 GHz wireless interface 450Mbps PHY Rate for 3x3 2.4Ghz, and 2.2Gbps PHY rate for 4x4 5Ghz with QAM1024 Maximum effective isotropic radiated power (EIRP) on 2.
PAGE 40
G-240W-J unit data sheet 5.2.1 7368 ISAM ONT G-240W-J Product Guide Configuring the G-240W-J to function as a single port ONT In addition to functioning as a residential gateway, the G-240W-J ONT can be configured to function as a single port ONT. In the custom configuration, the ONT reports to the OLT as one PPTP port. The physical Ethernet port of the ONT is managed by the RGW using the TR-069 protocol, rather than by the ONT/OMCI.
PAGE 41
7368 ISAM ONT G-240W-J Product Guide 5.2.3 G-240W-J unit data sheet TR-069 parameter support The G-240W-J ONT supports the following TR-069 features: • • • • • • • 5.2.3.1 Host object Port forwarding Optical parameters Object support for Wi-Fi parameters Statistics and troubleshooting Diagnostic parameter Timing parameter Host object support The ONT provides host object support for: InternetGatewayDeviceLANDevice.Hosts.Host. 5.2.3.
PAGE 42
G-240W-J unit data sheet 7368 ISAM ONT G-240W-J Product Guide These are the same optical parameters supported in the GUI. For more information, see Table 23 in the chapter “Configure a G-240W-J indoor ONT”. 5.2.3.
PAGE 43
7368 ISAM ONT G-240W-J Product Guide 5.2.3.7 G-240W-J unit data sheet Timing parameter support The ONT supports TR-069 timing parameters. 5.2.4 TR69 authentication using TLS and CA certificates G-240W-J ONTs support TLS, as well as ACS authentication using SHA-256 preinstalled certificates. If the URL is set to the https://... format, by default, the connection will use TLS without authentication mode. The ONT can also authenticate the ACS using a preinstalled CA certificate. 5.2.
PAGE 44
G-240W-J unit data sheet • • • • • 5.2.8 7368 ISAM ONT G-240W-J Product Guide hazardous potential foreign electrical motive force resistive faults receiver off-hook test ringers test TR-111 support The G-240W-J ONT supports TR-111, which extends the WAN Management Protocol defined in TR-069 to enhance the ability to remotely manage LAN devices. The device-gateway association enables an ACS to identify the associated gateway through which a device is connected.
PAGE 45
7368 ISAM ONT G-240W-J Product Guide G-240W-J unit data sheet Device interface DHCPv4 and DCHPv6 client and server Ethernet interface Firewall Hosts Interface stack IP interface configuration (1 of 2) Parameter category Functionality End user functional features Management server NAT Neighbor discovery Optical interface PPP interface QoS classification, QoS queue, and QoS shaper Routing and route information Timing Remote access User WiFi: AP configuration, radio configuration, and SSID configuration
PAGE 46
G-240W-J unit data sheet 5.2.10 7368 ISAM ONT G-240W-J Product Guide Mobile offload support As part of the E2E solution supported by the ISAM 7750 service router, the G240W-J ONT offers Mobile Offload support using a combination of EAP-SIM and ITU-T 802.11. EAP-SIM is an authentication method that uses the user credentials on the SIM card and EAP to authenticate the user with the Wi-Fi network, removing the need for user input (username and password).
PAGE 47
7368 ISAM ONT G-240W-J Product Guide 5.2.11.2 G-240W-J unit data sheet Soft GRE In soft GRE, only one side of the tunnel needs to be configured; the other end learns the remote IP addresses of all remote tunnel endpoints by examining the incoming GRE packets. GRE tunnels can be automatically created when devices attach to the AP, eliminating the need for each AP to be explicitly provisioned on the WLAN Gateway.
PAGE 48
G-240W-J unit data sheet 5.3 7368 ISAM ONT G-240W-J Product Guide G-240W-J software and installation feature support For information on installing or replacing the G-240W-J, see: • Install a G-240W-J indoor ONT • Replace a G-240W-J indoor ONT For information on the following topics, see the 7368 ISAM ONT Product Overview Guide: • • • • • • • • 5.
PAGE 49
7368 ISAM ONT G-240W-J Product Guide G-240W-J unit data sheet Figure 12 shows the G-240W-J indoor ONT with a fiber optic connector. Figure 12 G-240W-J indoor ONT with fiber optic connector Table 7 describes the physical connections for G-240W-J indoor ONTs.
PAGE 50
G-240W-J unit data sheet 7368 ISAM ONT G-240W-J Product Guide Table 7 G-240W-J indoor ONT physical connections Connection (1) Description POTS ports This connection is provided through RJ-11 ports. Up to two POTS connections are supported.The POTS ports support voice services. Ethernet ports This connection is provided through Ethernet RJ-45 connectors. Up to four 10/100/1000 Base-T Ethernet interfaces are supported.
PAGE 51
7368 ISAM ONT G-240W-J Product Guide G-240W-J unit data sheet Table 8 provides LED descriptions for G-240W-J indoor ONTs.
PAGE 52
G-240W-J unit data sheet 7368 ISAM ONT G-240W-J Product Guide USB Green solid Green flashing Off At least one device is connected to the USB port There is traffic activity on at least one device connected to the USB port No device is connected to the USB port INTERNET Green solid HSI WAN is connected: a) the device has an IP address assigned from IPCP, DHCP, or static, and no traffic has been detected; b) the session is dropped due to idle timeout but the PON link is still present.
PAGE 53
7368 ISAM ONT G-240W-J Product Guide 5.7 G-240W-J unit data sheet G-240W-J GEM ports and T-CONTs Table 12 lists the maximum number of supported T-CONTs and GEM ports. See the appropriate release Customer Release Notes for the most accurate list of supported devices.
PAGE 54
G-240W-J unit data sheet 7368 ISAM ONT G-240W-J Product Guide Table 14 Package P ONTs ONTL2UNI performance monitoring statistics ONT ONTL2UNI statistics G-240W-J (1) ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ Note (1) A 5 second polling window limitation exists on the ONT, therefore the margin of error for each 15-min window is 5 seconds Table 15 Package P ONTs PONONTTC, PONONTMCTC, PONONTTCHSI, PONONTTCCES, PONONTTCFLOW, PONONTTCVOIP performance monitoring statistics ONT PONONTTC, PONONTMCTC, PONONTTCHSI
PAGE 55
7368 ISAM ONT G-240W-J Product Guide 5.9 G-240W-J unit data sheet G-240W-J functional blocks G-240W-J indoor ONTs are single-residence ONTs that support Wireless (Wi-Fi) service. Wi-Fi service on these ONTs is compliant with the IEEE 802.11 standard and enabled or disabled using a WLAN button. In addition to the Wi-Fi service, these ONTs transmit Ethernet packets to four RJ-45 Ethernet ports and voice traffic to two RJ-11 POTS ports.
PAGE 56
G-240W-J unit data sheet 7368 ISAM ONT G-240W-J Product Guide POTS ports Control processor SoC DSP SoC Bridge Ethernet MACs GPON MAC Ethernet ports GPON 19421 ONT SoC technology consists of five key elements: • GPON MAC The Gigabit Passive Optical Network Media Access Control (GPON MAC) element on the SoC terminates the GPON interface using an optical diplexer. This interface supports GPON as described in G.984.3 (GPON TC Layer) ITU specification.
PAGE 57
7368 ISAM ONT G-240W-J Product Guide 5.10 G-240W-J unit data sheet G-240W-J standards compliance G-240W-J indoor ONTs are compliant with the following standards: • 802.1p marking and VLAN based pbit is supported • EN 300 328 v2.1.1 wide band data transmission standards for 2.4 GHz bands • EN 301 893 v2.1.1 5 GHz RLAN: Harmonized Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU G.711 support for FAX and modem connection G.984 support GPON interface (framing) G.984.
PAGE 58
G-240W-J unit data sheet 7368 ISAM ONT G-240W-J Product Guide provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
PAGE 59
7368 ISAM ONT G-240W-J Product Guide 5.11.1 G-240W-J unit data sheet Wi-Fi service G-240W-J indoor ONTs feature Wi-Fi service as well as voice and data services. Wi-Fi is a wireless networking technology that uses radio waves to provide wireless HSI and network connections. This ONT complies with the IEEE 802.11 standards, which the Wi-Fi Alliance defines as the basis for Wi-Fi technology. 5.11.1.
PAGE 60
G-240W-J unit data sheet 7368 ISAM ONT G-240W-J Product Guide Call History Data collection (ONTCALLHST) is supported, except for the following parameters: RTP packets (discarded), far-end RTCP and RTCP-XR participation, RTCP average and peak round trip delay, MOS, average jitter, number of jitter-buffer over-runs and under runs. (1 of 2) Considerations and limitations Some voice features are configurable on a per ONT basis, including Call Waiting, Call Hold, 3-Way Calling, and Call Transfer.
PAGE 61
7368 ISAM ONT G-240W-J Product Guide Issue: 01 G-240W-J unit data sheet 3FE-48009-AAAA-TCZZA 61
PAGE 62
Install a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide 6 Install a G-240W-J indoor ONT 6.1 Purpose 6.2 General 6.3 Prerequisites 6.4 Recommended tools 6.5 Safety information 6.6 Procedure 6.1 Purpose This chapter provides the steps to install a G-240W-J indoor ONT. 6.2 General The steps listed in this chapter describe mounting and cabling for G-240W-J indoor ONTs. 6.3 Prerequisites You need the following items before beginning the installation: • all required cables 6.
PAGE 63
7368 ISAM ONT G-240W-J Product Guide • • • • Install a G-240W-J indoor ONT voltmeter or multimeter optical power meter drill and drill bits paper clip 6.5 Safety information Read the following safety information before installing the unit. Danger 1 — Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits.
PAGE 64
Install a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide • See the detailed specifications in the G-240W-J unit data sheet for the temperature ranges for these ONTs. 6.6 Procedure Use this procedure to install a G-240W-J indoor ONT. 1 Place the indoor ONT unit: a On a flat surface, such as a desk; go to step 3. Note — The G-240W-J cannot be stacked with another ONT or with other equipment.
PAGE 65
7368 ISAM ONT G-240W-J Product Guide Figure 16 Install a G-240W-J indoor ONT G-240W-J ONT with connections and key mounting holes i Attach the wall mounting keyholes on the ONT. ii Drill two holes into the wall where the ONT will be mounted. If possible, mount the ONT on a wall stud. Do not drive the screw into the wall completely. Leave approximately 1/8 in. (6 mm) between the screw head and the wall surface. iii Drive the mounting screws into the holes.
PAGE 66
Install a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide 6 Connect the fiber optic cable with SC/APC adapter into the SC/APC connector; see Figure 16 for the location of the SC/APC connector. Danger — Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. Warning — Be careful to maintain a bend radius of no less than 1.5in. (3.8 cm) when connecting the fiber optic cable.
PAGE 67
7368 ISAM ONT G-240W-J Product Guide 3 Install a G-240W-J indoor ONT 13 Activate and test the services; see the 7368 Hardware and Cabling Installation Guide. 14 If used, configure the SLID; see the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide. 15 If necessary, reset the ONT. i Locate the Reset button; see Figure 3. ii Insert the end of a straightened paper clip or other narrow object into the hole in the Reset button to reset the ONT. STOP. This procedure is complete.
PAGE 68
Replace a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide 7 Replace a G-240W-J indoor ONT 7.1 Purpose 7.2 General 7.3 Prerequisites 7.4 Recommended tools 7.5 Safety information 7.6 Procedure 7.1 Purpose This chapter provides the steps to replace G-240W-J indoor ONTs. 7.2 General The steps listed in this chapter describe mounting and cabling for G-240W-J indoor ONTs. 7.3 Prerequisites You need the following items before beginning the installation: • all required cables 7.
PAGE 69
7368 ISAM ONT G-240W-J Product Guide • • • • Replace a G-240W-J indoor ONT RJ-45 cable plug crimp tool voltmeter or multimeter optical power meter drill and drill bits 7.5 Safety information Read the following safety information before replacing the unit. Danger 1 — Hazardous electrical voltages and currents can cause serious physical harm or death. Always use insulated tools and follow proper safety precautions when connecting or disconnecting power circuits.
PAGE 70
Replace a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide • See the detailed specifications in the G-240W-J unit data sheet for the ONT temperature ranges for these ONTs. 7.6 Procedure Use this procedure to replace a G-240W-J indoor ONT. 1 Deactivate the ONT services at the P-OLT. If you are using the SLID feature, this step is not required. The ONT and the services can remain in service (IS). i Use the RTRV-ONT command to verify the ONT status and th associated services.
PAGE 71
7368 ISAM ONT G-240W-J Product Guide Issue: 01 Replace a G-240W-J indoor ONT 3FE-48009-AAAA-TCZZA 71
PAGE 72
Replace a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide 3 Power down the unit by using the on/off power switch; see Figure 17 for the location of the power switch. 4 Disconnect the POTS, Ethernet, and power cables from the ONT; see Figure 17 for the connector locations on the G-240W-J indoor ONT. 5 Disconnect the fiber optic cable. Danger — Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters.
PAGE 73
68 ISAM ONT G-240W-J Product Guide 10 Replace a G-240W-J indoor ONT Danger — Fiber optic cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters. Connect the fiber optic cable with SC/APC adapter into the SC/APC connector. Figure 17 shows the location of the SC/APC connector. Danger — Fiber cables transmit invisible laser light. To avoid eye damage or blindness, never look directly into fibers, connectors, or adapters.
PAGE 74
Replace a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide Note — A new SLID or the old SLID may be used with the replacement ONT. If a new SLID is used, the new SLID must also be programmed at the P-OLT using TL1 or a network manager. If the old SLID is used, no changes need to be made at the P-OLT; see the operations and maintenance documentation for the OLT for more details. 17 Verify the ONT LEDs, voltage status, and optical signal levels; see the 7368 Hardware and Cabling Installation Guide.
PAGE 75
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT 8 Configure a G-240W-J indoor ONT 8.1 General 8.2 HGU mode GUI configuration 8.1 General Please refer to the configuration information provided with your OLT for the software configuration procedure for a G-240W-J ONT. For HTTP configuration procedures, please refer to the 7368 ISAM ONT Configuration, Management, and Troubleshooting Guide. 8.
PAGE 76
Configure a G-240W-J indoor ONT 2 7368 ISAM ONT G-240W-J Product Guide Enter your username and password in the Log in window, as shown in Figure 18. The default user name is userAdmin. The default password is a random number, which is included in the ONT kit. Figure 18 Web login window Caution — Pressing the Reset button for less than 10 seconds reboots the ONT; pressing the Reset button for 10 seconds resets the ONT to the factory defaults, except for the LOID and SLID.
PAGE 77
7368 ISAM ONT G-240W-J Product Guide • • • • • Procedure 7 Configure a G-240W-J indoor ONT WAN status IPv6 Home networking information optics module status statistics retrieval voice information Device information retrieval 1 Select Status > Device Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 19. Figure 19 Device Information window Note — Upon login, the GPON Home Gateway window displays the WAN status block on the bottom left part of each window.
PAGE 78
Configure a G-240W-J indoor ONT Device Name 7368 ISAM ONT G-240W-J Product Guide Name on the ONT (1 of 2) Field Description Vendor Name of the vendor Serial Number Serial number of the ONT Hardware version Hardware version of the ONT Boot version Boot version of the ONT Software version Software version of the ONT Chipset Chipset of the ONT Lot Number Production date of the ONT Device Running Time Amount of time the device has run since last reset in hours, minutes, and seconds (2 of 2
PAGE 79
7368 ISAM ONT G-240W-J Product Guide Procedure 8 Configure a G-240W-J indoor ONT LAN status retrieval 1 Select Status > LAN Status from the top-level menu in the GPON Home Gateway window, as shown in Figure 20. Figure 20 LAN status window Table 19 describes the fields in the LAN status window.
PAGE 80
Configure a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide Wireless Tx Packets Number of packets transmitted on the wireless connection (1 of 2) Field Description Wireless Rx Bytes Number of bytes received on the wireless connection Wireless Tx Bytes Number of bytes transmitted on the wireless connection Power Transmission (mW) Power of the wireless transmission, in mW Ethernet Information Ethernet Status Indicates whether the Ethernet connection is on or off Ethernet IP Address IP
PAGE 81
7368 ISAM ONT G-240W-J Product Guide Figure 21 Configure a G-240W-J indoor ONT WAN status window Table 20 describes the fields in the WAN status window. Table 20 WAN status parameters Field Description WAN connection list Drop-down menu listing all WAN connections. The connection shown is the connection for which WAN status will be shown.
PAGE 82
Configure a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide Tx Dropped Number of packets dropped on the transmit WAN connection Rx Dropped Number of packets dropped on the receive WAN connection Err Packets Number of errored packets on the WAN connection (2 of 2) 2 Click Refresh to update the displayed information. 3 STOP. This procedure is complete.
PAGE 83
7368 ISAM ONT G-240W-J Product Guide Table 21 Configure a G-240W-J indoor ONT WAN status IPv6 parameters Field Description WAN connection list Drop-down menu listing all WAN connections. The connection shown is the connection for which WAN status will be shown.
PAGE 84
Configure a G-240W-J indoor ONT Figure 23 7368 ISAM ONT G-240W-J Product Guide Home networking information window Table 22 describes the fields in the Home networking window. Table 22 Field Home networking parameters Description Local Interface Ethernet Table displays the number of Ethernet connections and their settings Wireless (2.4GHz) Table displays the number of wireless connections and their settings Wireless (5GHz) Wireless Settings (2.
PAGE 85
7368 ISAM ONT G-240W-J Product Guide Access Point Configure a G-240W-J indoor ONT Hexadecimal address of the wireless access point Local Devices Table entry Each entry indicates the status (active or inactive), connection type, device name, IP address, hardware address, and IP address allocation of each connected local device. (2 of 2) Procedure 12 2 Click Delete to delete a particular local device connection. 3 Click Refresh to update the displayed information. 4 STOP.
PAGE 86
Configure a G-240W-J indoor ONT Table 23 7368 ISAM ONT G-240W-J Product Guide Optics module status parameters Field Description Laser Bias Current (ONT ANI-ONT-Side Optical Measurements) Laser bias current, measured in uA Optics Module Voltage (ONT ANI-ONT-Side Optical Measurements) Optics module voltage, measured in V Optics Module Temperature (ONT ANI-ONT-Side Optical Measurements) Optics module temperature, measured in C Rx Optics Signal Level at 1490 nm (ONT ANI-ONT-Side Optical Measurements
PAGE 87
7368 ISAM ONT G-240W-J Product Guide Figure 25 Configure a G-240W-J indoor ONT LAN ports Statistics window Figure 26 shows the statistics for the WAN ports.
PAGE 88
Configure a G-240W-J indoor ONT Figure 26 7368 ISAM ONT G-240W-J Product Guide WAN ports statistics window If there are no WAN connections to display, the system displays a message, as shown in Figure 27.
PAGE 89
7368 ISAM ONT G-240W-J Product Guide Figure 27 Configure a G-240W-J indoor ONT WAN ports statistics message Figure 28 shows the statistics for the WLAN ports.
PAGE 90
Configure a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide If there are no WLAN connections to display, the system displays a message, as shown in Figure 29. Figure 29 2 90 WLAN ports statistics message STOP. This procedure is complete.
PAGE 91
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT 1 Procedure 14 Voice information retrieval Select Status > Voice Information from the top-level menu in the GPON Home Gateway window, as shown in Figure 30. Figure 30 Voice Information window Table 24 describes the fields in the Voice Information window. Table 24 Voice Information parameters Field Description Line Choose a line from the drop-down menu. The default is Line 1.
PAGE 92
Configure a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide Soft Switch(1) Proxy IP address; blank if the line is not registered Phone Number(1) Phone number configured for a telephone line 1; +13290611266 (1 of 2) Field Description Register Status The default is Registered Blank if no voice service is provisioned Register Error Code SIP standard error code for the register status; for example, 401, 403, 503 This field is blank if the register is set to OK Register Error Reason SIP sta
PAGE 93
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT 1 • • • • • Procedure 15 DNS TR-069 GRE tunnel QoS US (upstream) classification LAN networking configuration Select Network > LAN from the top-level menu in the GPON Home Gateway window, as shown in Figure 31. Figure 31 LAN network window Table 25 describes the fields in the LAN network window.
PAGE 94
Configure a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide Port Mode All Ports to Bridge Mode Select this checkbox to set all ports to Bridge mode Port 1 - 4 Drop-down port mode for each port: Route mode or Bridge mode IPv4 Address IP Address of the ONT Subnet Mask Subnet mask of the ONT DHCP Enable Select this checkbox to enable DHCP DHCP Start IP Address Starting DHCP IP address (1 of 2) Field Description DHCP End IP Address Ending DHCP IP address DHCP Lease Time DHCP lease ti
PAGE 95
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT 1 Procedure 16 LAN IPv6 networking configuration Select Network > LAN_IPv6 from the top-level menu in the GPON Home Gateway window, as shown in Figure 32. Figure 32 LAN IPv6 network window Table 26 describes the fields in the LAN IPv6 network window. Table 26 Field LAN IPv6 network parameters Description IPv6 LAN Host Configuration Issue: 01 DNS Server Choose a DNS server from the drop-down menu.
PAGE 96
Configure a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide LAN Prefix This field appears if you selected the “Static” option for the “prefix config” field. Type a connection. Enable Select this checkbox to enable the LAN connection (1 of 2) Field Description Prefix Config Choose a prefix config option from the drop-down menu, either WANConnection (prefix will be obtained from the WAN) or Static (enables you to enter the prefix).
PAGE 97
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT 1 Procedure 17 WAN networking configuration Select Network > WAN from the top-level menu in the GPON Home Gateway window, as shown in Figure 33.
PAGE 98
Configure a G-240W-J indoor ONT Figure 33 7368 ISAM ONT G-240W-J Product Guide WAN network window Table 27 describes the fields in the WAN network window.
PAGE 99
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT 1 Issue: 01 Connection Type Choose a connection type: IPoE or PPPoE IP mode Choose an IP mode from the drop-down menu: IPv4 or IPv6 Enable/Disable Select this checkbox to enable the WAN connection NAT Select this checkbox to enable NAT Service Select the checkboxes to enable service types for this connection Enable VLAN Select this checkbox to enable VLAN VLAN ID Enter the VLAN ID VLAN PRI Enter the VLAN PRI WAN IP Mode
PAGE 100
Configure a G-240W-J indoor ONT 4 Procedure 18 7368 ISAM ONT G-240W-J Product Guide STOP. This procedure is complete. WAN DHCP configuration Select Network > WAN DHCP from the top-level menu in the GPON Home Gateway window, as shown in Figure 34. Figure 34 WAN DHCP window Table 28 describes the fields in the WAN DHCP window.
PAGE 101
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT 1 2 Configure a WAN DHCP option. 3 Click Save. 4 STOP. This procedure is complete. Procedure 19 WiFi 2.4G networking configuration 1 Select Network > WiFi 2.4G from the top-level menu in the GPON Home Gateway window, as shown in Figure 35. Figure 35 Issue: 01 WiFi 2.
PAGE 102
Configure a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide Table 29 describes the fields in the WiFi 2.4G network window. Table 29 WiFi 2.
PAGE 103
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT Field Description Mode Choose a Wi-Fi mode from the drop-down menu: • • • • • Bandwidth auto (b/g/n) b g n b/g Choose from: • • • 20 MHz 40 MHz 20/40 MHz Channel Choose a channel from the drop-down menu or choose Auto to have the channel automatically assigned Transmitting Power Choose a percentage for the transmitting power from the drop-down menu: • • • • Low (25%) Medium (50%) High (75%) Maximum (100%) WMM Choose Enabl
PAGE 104
Configure a G-240W-J indoor ONT WPA Encryption Mode 7368 ISAM ONT G-240W-J Product Guide Choose a WPA encryption mode from the drop-down menu: • • • TKIP AES TKIP/AES WPA Key Enter the WPA key Enable WPS Enable or disable WPS from this drop-down menu (2 of 3) Field Description WPS Mode Choose a WPS mode from the drop-down menu: PBC (Push Button Connect) or PIN (Personal Identification Number) (3 of 3) Notes (1) When Encryption Mode is set to “WPA/WPA2 Enterprise”, the following options are no
PAGE 105
7368 ISAM ONT G-240W-J Product Guide Procedure 20 Configure a G-240W-J indoor ONT WiFi 5G networking configuration 1 Select Network > WiFi 5G from the top-level menu in the GPON Home Gateway window, as shown in Figure 36. Figure 36 WiFi 5G network window Table 30 describes the fields in the WiFi 5G network window.
PAGE 106
Configure a G-240W-J indoor ONT Transmitting Power 7368 ISAM ONT G-240W-J Product Guide Choose a percentage for the transmitting power from the drop-down menu: • • • • Low (20%) Medium (40%) High (60%) Maximum (100%) WMM Choose Enable or Disable from the drop-down menu to enable or disable WiFi multi-media Total MAX Users Enter the total number of MAX users DFS re-entry Choose Enable or Disable from the drop-down menu to enable or disable DFS re-entry SSID Configuration SSID Select Choose the S
PAGE 107
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT 4 Click Save. 5 STOP. This procedure is complete. Procedure 21 Wireless scheduling 1 Select Network > Wireless Schedule from the top-level menu in the GPON Gateway window, as shown in Figure 37. Figure 37 Wireless Schedule window 2 Select the Schedule Function checkbox to turn the wireless signal off for the configured period. 3 Click the plus sign (+) to add a scheduling rule.
PAGE 108
Configure a G-240W-J indoor ONT 6 7368 ISAM ONT G-240W-J Product Guide If you chose Individual Days, select the checkboxes for the desired days. The Recurrence Pattern shows the rules created to date. Procedure 22 7 If desired, click the plus sign (+) to add more rules. 8 Click Save Changes. 9 STOP. This procedure is complete. Routing configuration 1 Select Network > Routing from the top-level menu in the GPON Home Gateway window, as shown in Figure 38.
PAGE 109
7368 ISAM ONT G-240W-J Product Guide Table 31 Configure a G-240W-J indoor ONT Routing network parameters Field Description Enable Routing Select this checkbox to enable routing Destination IP Address Enter the destination IP address Destination Netmask Enter the destination network mask (1 of 2) Field Description Gateway Enter the gateway address IPv4 Interface Choose a WAN connection previously created in the WAN network window from the drop-down menu Forwarding Policy Choose a forwardin
PAGE 110
Configure a G-240W-J indoor ONT Figure 39 7368 ISAM ONT G-240W-J Product Guide DNS network window Table 32 describes the fields in the DNS network window. Table 32 110 DNS network parameters Field Description DNS Proxy Select the Enabled checkbox to enable the DNS proxy Domain Name Domain name IPv4 Address Domain IP address Origin Domain Origin domain name New Domain New domain name 2 Select the Enabled checkbox and click Save to enable the DNS proxy.
PAGE 111
7368 ISAM ONT G-240W-J Product Guide Procedure 24 Configure a G-240W-J indoor ONT TR-069 configuration Note — You need to have administrator (SuperAdmin) account privileges for TR-069 configuration; a user account (userAdmin) does not provide access to this procedure. 1 Select Network > TR-069 from the top-level menu in the GPON Home Gateway window, as shown in Figure 40. Figure 40 TR-069 network window Table 33 describes the fields in the TR-069 network window.
PAGE 112
Configure a G-240W-J indoor ONT 4 Procedure 25 7368 ISAM ONT G-240W-J Product Guide STOP. This procedure is complete. GRE Tunnel configuration 1 Select Network > GRE Tunnel from the top-level menu in the GPON Home Gateway window, as shown in Figure 41. Figure 41 GRE Tunnel window Table 34 describes the fields in the GRE Tunnel window. Table 34 GRE Tunnel parameters Field Description Tunnel Name Choose Create new GRE Tunnel, or Choose an existing tunnel from the drop-down menu.
PAGE 113
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT WAN Interface Choose a WAN interface from the drop-down menu. GRE tunnels can only be created on HSI-enabled WAN interfaces. Primary Remote End Secondary Remote End (optional) Enter an IP address or FQDN that is unique in the system. If the primary remote endpoint is down or unreachable, the secondary remote endpoint becomes active, if configured.
PAGE 114
Configure a G-240W-J indoor ONT Figure 42 7368 ISAM ONT G-240W-J Product Guide QoS Config window (L2) Figure 43 shows the window for configuring QoS L3 (Layer 3 packet sizes).
PAGE 115
7368 ISAM ONT G-240W-J Product Guide Figure 43 Configure a G-240W-J indoor ONT QoS Config window (L3) Table 35 describes the fields in the QoS Config window. Table 35 Issue: 01 QoS Config parameters Field Description Type Choose a QoS service layer type from the drop-down menu L2 or L3.
PAGE 116
Configure a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide (1 of 2) Field Description Forwarding Policy Enter the number for the forwarding policy (range: 1-7) Additional fields for L3 Protocol Choose a protocol from the drop-down menu, or select the Exclude checkbox Application Choose an application from the drop-down menu Source IP and Source IP Mask Enter the values for the source IP and IP mask, or select the Exclude checkbox Destination IP and Destination IP Mask Enter the values
PAGE 117
7368 ISAM ONT G-240W-J Product Guide 1 Configure a G-240W-J indoor ONT Select Network > US Classifier from the top-level menu in the GPON Home Gateway window, and select the Policy tab, as shown in Figure 44. All classifier policies are displayed in the policy table in the window. Figure 44 US Classifier Policy window Table 36 describes the fields in the US Classifier Policy window.
PAGE 118
Configure a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide 2 Select a tunnel interface. 3 Enter a VLAN ID and priority level. 4 Click Save. 5 To delete a policy, click the Delete option for the applicable policy in the policy table. A policy can only be deleted if it is not associated with any classifier rules. 6 Select Network > US Classifier from the top-level menu in the GPON Home Gateway window, and select the Classifier tab, as shown in Figure 45.
PAGE 119
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT Source MAC Click to enter a source MAC Destination MAC Click to enter a destination MAC Source IP Click to enter a source IP (1 of 2) Field Description Destination IP Click to enter a destination IP Source Port Click to enter a source port Destination Port Click to enter a destination port Protocol Click to enter a protocol Priority Choose a priority level from 1 to 8. The lower the number, the higher the priority.
PAGE 120
Configure a G-240W-J indoor ONT Figure 46 7368 ISAM ONT G-240W-J Product Guide US Classifier Rules window Table 38 describes the fields in the US Classifier Rules window. Table 38 120 US Classifier Rules parameters Field Description Policy Choose a policy from the drop-down menu Classifier Choose a classifier from the drop-down menu Interface Choose an interface from the drop-down menu; for example, None, LAN, 2.4G SSID, 5G SSID.
PAGE 121
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT 13 To delete a classifier rule, click the Delete option for the applicable classifier rule in the classifier rules table. 14 STOP. This procedure is complete. 8.2.
PAGE 122
Configure a G-240W-J indoor ONT Figure 47 7368 ISAM ONT G-240W-J Product Guide Firewall window Four security options are available: High, Low, Off, and Advanced. High—Traffic denied inbound and minimally permit common services outbound Low—All outbound traffic and pinhole-defined inbound traffic is allowed Off—All inbound and outbound traffic is allowed Advanced—Advanced firewall configuration applies as specified Table 39 describes the fields in the firewall window.
PAGE 123
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT 2 Configure the firewall. 3 Click Save. 4 STOP. This procedure is complete. Procedure 29 MAC filter configuration 1 Select Security > Mac Filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 48. Figure 48 MAC filter window Table 40 describes the fields in the MAC filter window.
PAGE 124
Configure a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide MAC Filter Mode Choose the MAC filter mode from the drop-down menu: Blocked or Allowed LAN Port LAN port range MAC Address Choose a MAC address from the drop-down menu or enter the address in the text field Wi-Fi SSID Choose the MAC filter mode from the drop-down menu: Blocked or Allowed SSID Select Choose the SSID from the drop-down menu Enable Select this checkbox to enable the MAC filter MAC Address Choose a MAC address fr
PAGE 125
7368 ISAM ONT G-240W-J Product Guide Figure 49 Configure a G-240W-J indoor ONT IP filter window Table 41 describes the fields in the IP filter window. If the firewall level is not set to advanced, the IP filter rules are not available.
PAGE 126
Configure a G-240W-J indoor ONT 4 Procedure 31 STOP. This procedure is complete. URL filter configuration 1 Figure 50 7368 ISAM ONT G-240W-J Product Guide Select Security > URL Filter from the top-level menu in the GPON Home Gateway window, as shown in Figure 50. URL Filter window Note — You cannot use URL filtering for HTTPS. The URL is encrypted when using HTTPS. Table 42 describes the fields in the URL Filter window.
PAGE 127
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT URL List Issue: 01 URL Address Type the URL address Port - default to 80 Type the port number; the default is 80 2 Configure the URL Filter. 3 Click Add Filter. 4 STOP. This procedure is complete.
PAGE 128
Configure a G-240W-J indoor ONT Procedure 32 7368 ISAM ONT G-240W-J Product Guide Parental control 1 Select Security > Parent Control from the top-level menu in the GPON Gateway window, as shown in Figure 51.
PAGE 129
7368 ISAM ONT G-240W-J Product Guide Figure 51 Configure a G-240W-J indoor ONT Parental Control window Table 43 describes the fields in the Parental Control window.
PAGE 130
Configure a G-240W-J indoor ONT Access Control 7368 ISAM ONT G-240W-J Product Guide Select this checkbox to enable access control Add Access Control rule Policy Name Enter a name for the parental control policy or choose a policy from the list MAC Address Enter the MAC address or choose a MAC address from the list IPv4 Address Enter the IPv4 address for the device or choose an IPv4 address from the list Url Port Enter the URL port for the device Days of week Choose Every Day, or Individual Days
PAGE 131
7368 ISAM ONT G-240W-J Product Guide Figure 52 Configure a G-240W-J indoor ONT DMZ and ALG window Table 44 describes the fields in the DMZ and ALG window.
PAGE 132
Configure a G-240W-J indoor ONT Procedure 34 7368 ISAM ONT G-240W-J Product Guide Access control configuration This procedure describes how to configure the access control level (ACL). Note 1 — ACL takes precedence over the firewall policy. Note 2 — The trusted network object will be shared for all WAN connections; it is not applied individually to a WAN connection. 1 Select Security > Access Control from the top-level menu in the GPON Home Gateway window, as shown in Figure 53.
PAGE 133
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT Trusted Network Source IP Start Enter a start IP address for the new subnet trusted network Source IP End Enter an end IP address for the new subnet trusted network (2 of 2) 2 Select a WAN connection from the drop-down menu. 3 Click to enable or disable Trusted Network. 4 Select an access control level for each of the four protocols: ICMP, SSH, HTTP, and TR069 for both the WAN and the LAN side. 5 Click Save.
PAGE 134
Configure a G-240W-J indoor ONT 1 Figure 54 7368 ISAM ONT G-240W-J Product Guide Select Application > Port forwarding from the top-level menu in the GPON Home Gateway window, as shown in Figure 54. Port forwarding window Table 46 describes the fields in the port forwarding window.
PAGE 135
7368 ISAM ONT G-240W-J Product Guide Procedure 36 Configure a G-240W-J indoor ONT 3 Click Add. 4 STOP. This procedure is complete. Port triggering 1 Select Application > Port Triggering from the top-level menu in the GPON Gateway window, as shown in Figure 55. Figure 55 Port Triggering window Table 47 describes the fields in the Port Triggering window.
PAGE 136
Configure a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide Field Description Open Protocol Choose the open port protocol from the drop-down menu: • • • Trigger Protocol TCP UDP TCP/UDP Choose the triggering port protocol from the drop-down menu: • • • TCP UDP TCP/UDP Enable Triggering Select this checkbox to enable port triggering WAN Connection List Choose a WAN connection from the drop-down menu Note: only active devices are shown on this menu (2 of 2) 136 2 Configure port trig
PAGE 137
7368 ISAM ONT G-240W-J Product Guide Procedure 37 Configure a G-240W-J indoor ONT DDNS configuration 1 Select Application > DDNS from the top-level menu in the GPON Home Gateway window, as shown in Figure 56. Figure 56 DDNS window Table 48 describes the fields in the DDNS window.
PAGE 138
Configure a G-240W-J indoor ONT 4 Procedure 38 STOP. This procedure is complete. NTP configuration 1 Figure 57 7368 ISAM ONT G-240W-J Product Guide Select Application > NTP from the top-level menu in the GPON Home Gateway window, as shown in Figure 57. NTP window Table 49 describes the fields in the NTP window.
PAGE 139
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT Field Description Third Time Server Choose a time server from the drop-down menu or choose Customer setting and enter the address of the time server. Interval Time Interval at which to get the time from the time server, in seconds Time Zone Choose the local time zone from the drop-down menu (2 of 2) Procedure 39 2 Configure NTP. 3 Click Save. 4 STOP. This procedure is complete.
PAGE 140
Configure a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide prevents the print job from being completed, a generic error message is returned to the LAN client. Up to four print jobs at a time are supported. 1 Select Application > USB from the top-level menu, as shown in Figure 58. Figure 58 USB window Table 50 describes the fields in the USB window.
PAGE 141
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT Re-enter Password Password for the FTP server Enable SFTP Server Select this checkbox to enable using an SFTP server Enable SFTP for Remote Access Select this checkbox to enable SFTP for remote access Username Username for the SFTP server Password Password for the SFTP server Re-enter Password Password for the SFTP server Enable Printer Sharing Select this checkbox to enable printer sharing Printer sharing is disabled by def
PAGE 142
Configure a G-240W-J indoor ONT Figure 59 UPnP and DLNA window 2 Select the Enable UPnP/DLNA checkbox to enable UPnP/DLNA. 3 Click Save/Apply. 4 STOP. This procedure is complete. Procedure 41 Voice setting 1 142 7368 ISAM ONT G-240W-J Product Guide Select Application > Voice Setting from the top-level menu in the GPON Home Gateway window, as shown in Figure 60.
PAGE 143
7368 ISAM ONT G-240W-J Product Guide Figure 60 Configure a G-240W-J indoor ONT Voice setting window Table 51 describes the fields in the Voice Setting window.
PAGE 144
Configure a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide Registrar Server Port Enter the registrar server port UserAgentDomain Enter the user agent domain UserAgentPort Enter the user agent port DigitMap A string of characters with a length limit of 1024 bytes. A dial plan can consist of several dial plan tokens. Each token is a component of the overall dial plan.
PAGE 145
7368 ISAM ONT G-240W-J Product Guide • • • • • Procedure 42 Configure a G-240W-J indoor ONT reboot device restore factory defaults diagnose WAN connections view log diagnose PPPoE connection Password configuration A password must adhere to the password rules, which are as follows: • the password may consist of uppercase letters, lowercase letters, digital numbers, and the following special characters ! # + , - / @ _ : = ] • • • the password length must be from 8 to 24 characters • the same charact
PAGE 146
Configure a G-240W-J indoor ONT • • 1 7368 ISAM ONT G-240W-J Product Guide the first character cannot be a special character there are not enough character classes Select Maintenance > Password from the top-level menu in the GPON Home Gateway window, as shown in Figure 61. Figure 61 Password window Table 52 describes the fields in the password window.
PAGE 147
7368 ISAM ONT G-240W-J Product Guide 4 Procedure 43 Configure a G-240W-J indoor ONT STOP. This procedure is complete. WAN speed test 1 Select Maintenance > Speed Test from the top-level menu in the GPON Home Gateway window, as shown in Figure 62. Figure 62 2 Speed Test window Click Start to start the speed test. Enter the URL for the test server in the pop-up window. 3 Procedure 44 LOID configuration 1 Issue: 01 STOP. This procedure is complete.
PAGE 148
Configure a G-240W-J indoor ONT Figure 63 7368 ISAM ONT G-240W-J Product Guide LOID Config window Table 53 describes the fields in the LOID configuration window. Table 53 Field Description LOID Type the LOID; the maximum number of characters is 24 If the password is null, this field may be left blank Password Type the password; the maximum number of characters is 12 2 Configure the LOID. 3 Click Save/Apply. 4 STOP. This procedure is complete.
PAGE 149
7368 ISAM ONT G-240W-J Product Guide Figure 64 Configure a G-240W-J indoor ONT SLID configuration window Table 54 describes the fields in the SLID configuration window. Table 54 Issue: 01 SLID configuration parameters Field Description Current SLID Displays current SLID Enter new SLID Input new SLID SLID Mode Choose a SLID mode from the drop-down menu 2 Configure the new SLID. 3 Click Save. 4 STOP. This procedure is complete.
PAGE 150
Configure a G-240W-J indoor ONT Procedure 46 7368 ISAM ONT G-240W-J Product Guide Device management 1 Select Maintenance > Device Management from the top-level menu in the GPON Home Gateway window, as shown in Figure 65. Figure 65 Device management window Table 55 describes the fields in the Device management window.
PAGE 151
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT 2 Configure an alias for a specific host. 3 Click Add. 4 STOP. This procedure is complete. Procedure 47 Backup and restore 1 Select Maintenance > Backup and Restore from the top-level menu in the GPON Home Gateway window, as shown in Figure 66. Figure 66 2 Issue: 01 Backup and Restore window Click Choose file and select a backup file.
PAGE 152
Configure a G-240W-J indoor ONT 3 Click Import Config File to restore the ONT to the saved backup or click Export Config File to export the current ONT configuration to the backup file. 4 STOP. This procedure is complete. Procedure 48 Upgrade firmware 1 Select Maintenance > Firmware Upgrade from the top-level menu in the GPON Home Gateway window, as shown in Figure 67. Figure 67 152 7368 ISAM ONT G-240W-J Product Guide Firmware upgrade window 2 Click Choose file and select the firmware file.
PAGE 153
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT 1 Procedure 49 Reboot ONT Select Maintenance > Reboot Device from the top-level menu in the GPON Home Gateway window, as shown in Figure 68. Figure 68 Procedure 50 Reboot window 2 Click Reboot to reboot the ONT. 3 STOP. This procedure is complete. Restore factory defaults Select Maintenance > Factory Default from the top-level menu in the GPON Home Gateway window, as shown in Figure 69.
PAGE 154
Configure a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide 1 Figure 69 Procedure 51 Factory default window 2 Click Factory Default to reset the ONT to its factory default settings. 3 STOP. This procedure is complete. Diagnose WAN connections Select Maintenance > Diagnose from the top-level menu in the GPON Home Gateway window, as shown in Figure 70.
PAGE 155
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT 1 Figure 70 Issue: 01 Diagnose window 2 Choose a WAN connection to diagnose from the drop-down menu. 3 Enter the IP address or domain name. 4 Select the test type: ping, traceroute, or both. 5 Enter the number of ping attempts to perform (1 - 1000); the default is 4. 6 Enter a ping packet length (64-1024); the default is 64. 7 Enter the maximum number of trace hops (1-255); the default is 30. 8 Click Start Test.
PAGE 156
Configure a G-240W-J indoor ONT 7368 ISAM ONT G-240W-J Product Guide 9 Click Cancel to cancel the test. 10 STOP. This procedure is complete. Procedure 52 View log files 1 Select Maintenance > Log from the top-level menu in the GPON Home Gateway window, as shown in Figure 71.
PAGE 157
7368 ISAM ONT G-240W-J Product Guide • • • • 3 Warning Notice Informational Debug Choose a reading level from the drop-down menu to determine which types of events to display from the log file: • • • • • • • • Emergency Alert Critical Error Warning Notice Informational Debug 4 The log file is displayed at the bottom of the window. 5 STOP. This procedure is complete.
PAGE 158
Configure a G-240W-J indoor ONT Figure 72 2 PPPoE Diagnostics window Click Check to view the results for the PPPoE diagnostics, as shown in Figure 73.
PAGE 159
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT Table 56 describes the fields on the PPPoE diagnostics results window. Table 56 3 8.2.
PAGE 160
Configure a G-240W-J indoor ONT Figure 74 7368 ISAM ONT G-240W-J Product Guide RG Troubleshooting Counters window Table 57 describes the fields in the RG Troubleshooting Counters window.
PAGE 161
7368 ISAM ONT G-240W-J Product Guide Configure a G-240W-J indoor ONT WAN Status Whether the WAN linking is (UP) or not (DOWN) Latency This test is used to determine the lowest round-trip time in milliseconds by pinging the target server multiple times Click Latency Test to specify the time for the test The default is weekly, performed at idle to a public server DNS Response Time This test is used to determine the lowest round-trip time in milliseconds by sending a request to the target DNS server Cli
PAGE 162
ONT configuration file over OMCI 7368 ISAM ONT G-240W-J Product Guide 9 ONT configuration file over OMCI 9.1 Purpose 9.2 Supported configuration file types 9.3 ONT configuration file over OMCI 9.1 Purpose This procedure describes how to use configuration files over OMCI to configure ONTs.
PAGE 163
7368 ISAM ONT G-240W-J Product Guide PRE ONT pre-configuration file ONT configuration file over OMCI The XML-based PRECONFIG file controls the working mechanics of the ONT for various services. The default behavior of different ONTs may vary based on the factory settings. The pre-configuration file includes the factory default value for the residential gateway.
PAGE 164
ONT configuration file over OMCI GFT 7368 ISAM ONT G-240W-J Product Guide This text-based json script file controls the default behavior of the G.Fast ONT. This file includes the provisioning parameters of the G.fast transports layer; it does not include VLAN or QoS provisioning. While the ONT functions well with the default values; they can optionally be customized. While default values can work in VDSL mode, a download file is required for the device to function as a G.fast ONT. G.
PAGE 165
7368 ISAM ONT G-240W-J Product Guide ONT configuration file over OMCI Use this procedure to configure ONTs using configuration files via OMCI.
PAGE 166
ONT configuration file over OMCI 7368 ISAM ONT G-240W-J Product Guide Procedure 55 Configuring an ONT using a configuration file via OMCI 1 Generate the TAR file to be uploaded to the OLT. Using the raw configuration file(s) provided by Nokia, generate the TAR file as follows: i On a Linux platform, rename the raw configuration file to adhere to the naming convention, as described in section 9.2. ii Tar the ABCXXXXVER raw configuration file: tar -cf ABCXXXXVER.
PAGE 167
7368 ISAM ONT G-240W-J Product Guide ONT configuration file over OMCI FILENAME1 will be downloaded and FILENAME1 will be made active. An ONT reboot is required. iii If pland-cfgfileX=Disabled and dnload-cfgfileX= FILENAME2 FILENAME2 will be downloaded and FILENAME2 will be made passive. An ONT reboot is not required. iv If pland-cfgfileX=FILENAME3 and dnload-cfgfileX= FILENAME 4, the OLT reports an error because the filenames are not the same.
PAGE 168
Customer document and product support Customer documentation Customer Documentation Welcome Page Technical Support Customer Documentation Technical Support Documentation feedback Customer Documentation Feedback Copyright 2019 Nokia.