Installation Guide www.janusintl.
INTRODUCTION Before Starting This installation guide provides instructions for installing a Nokē Screen in various settings such as pedestrian gates, parking entries, and interior pedestals. The Nokē Screen controls existing electronic locks. This guide is intended for licensed electricians and trained technicians only. Make sure you have received the parts listed below--contact your dealer for any missing parts. The Nokē Screen also includes a software application (app) which can be downloaded from noke.
SPECIFICATIONS Dimensions 2in. x 0.8in. x 5in. (5cm. x 2cm. x 12.7cm) Material Polished Zinc Connectivity Bluetooth enabled, WiFi Power 12V - 24V DC input (requires 2 Amp capable), PoE Backup Battery None (backup from power supply switch) Lock Activation 850mA / 0.01-25 Sec.
INSTALLATION Installing the Backplate Before drilling into walls, make sure there are no water or electrical lines in the way. For wall mounting, use a pencil to trace the desired back plate holes onto the wall. Then, drill the holes in the wall and set the anchors. If mounting on any masonry exterior walls, use machine screws for metal plates and toggle screws for interior drywall. Check that the bottom tabs on the back plate are facing away from the wall.
INITIALIZATION Wiring When using PoE for power and data, connect the CAT6 into the control board port as shown below. 1. No devices other than Nokē products should be plugged into the switch. 2. Use approved conduit only--never run high voltage inside. Always adhere to all local building and electrical codes. 3. If there are any discrepancies between your local building codes and this manual, always adhere to local codes, which take precedence.
INITIALIZATION When not using PoE for power and data, use an Altronix power supply to power Nokē Screen. Data will need to be provided via WiFi. First, connect the power supply wire (12V24V DC) and both the ground (GND) and earth ground (ESD GND) wires to their relay push pin connectors on the relay board, and then insert the relay board into the control board. (Use only 18-gauge, 2 conductor wire.
INITIALIZATION Setting Up the Application To initialize the Nokē Screen, you can either gather information from the unit and submit it online or use the Nokē Smart Entry mobile device application (available on Google Play/Apple stores). The website is: www.smartentry.noke.com. Before initializing the device, you need a Nokē login and password (see your Janus International Project Manager), and the device must be connected to a PoE cable or 12V24V power supply and data line (Ethernet cable).
INITIALIZATION 7. Press Upload. 8. Go to the menu page (icon on the upper- right corner of the app) and press Add Gateway. 9. Name the gateway with a similar name to the device name. 10. Use the Comments section to record how the device was wired (for example, PoE, 12V D.C. etc.).
INITIALIZATION 11. Press Save and Finish.
INITIALIZATION 12. Press the + button in the upper right-hand corner of the app to add your device. 13. Using the app, scan the QR code on the Nokē Screen display. 14. After scanning, name your device and select what type of entry it controls (for example, gate, door, elevator, sliding door, etc.). Consider using a logical name or consult with a facility manager when naming the device.
INITIALIZATION 15. When finished, press Done.
INITIALIZATION Connecting to WiFi Before connecting the Nokē Screen keypad to the WiFi, you need your device’s SSID and password. Usually, you can find this on the bottom of your device. To connect to WiFi, 1. From the Nokē Smart Entry Web Portal, select Settings > WiFi, and then select the + icon in the top-right corner. The Add WiFi Network form is displayed. 2. Add your device’s Network SSID and Network Passphrase into the form, and then select Add WiFi Network. 3.
DIAGRAMS Providing Power and Data Cat6 Router Cat6 Gate PoE Switch Nokē Screen PoE PoE Office Switch 18/2 Cat6 Cat6 18/2 Router Power Supply (Altronix) Non-PoE Office 12 18/2 Nokē Screen Gate
MOUNTING Considerations Before installing a Nokē Screen, consider how it will be used. For example, if the Nokē Screen is for cars at a gate, you should ensure the keypad can be reached from the driver side window. For Nokē Screens that will be operated by those walking up to a facility, the Nokē Screen should be mounted so pedestrians (and those with disabilities) can reach the keypad with ease.
MOUNTING Options For walk up access, the Nokē Screen is weather resistant and can be mounted on external walls or on a goose-neck pedestal (see below).
MOUNTING Elevator Conventional Door 15
INFORMATION Maintenance Inspect the Nokē Screen for tampering or damage at the end of the installation. Should the device be damaged, or the screen cracked, immediately take it out of service. Only wipe the Nokē Screen with a clean dry cloth, as needed. Never use liquids or harsh chemicals. Disclaimer Always operate the Nokē Screen in a safe manner and in full compliance with this manual and any applicable laws related thereto. No warranties express or implied are contained herein.
FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.