User guide

ManualsBrandsNM Engineering ManualsCar658856

NM Engineering ∞ 3300 Corte Malpaso, Camarillo, CA 93012 ∞ 805.388.7171 ∞ 805.388.0030 FAX

engineer@nm-eng.com ∞ www.nm-eng.com

PARTS INCLUDED:

[1] Stainless Steel Intake Pipe Bracket

[1] Stainless Steel Fresh Air Hose Bracket

[1] Silicone Turbo Inlet Hose

[1] 2.75” Silicone Coupler

[1] Aluminum or Carbon Fiber Intake Pipe

[1] Air Filter

[3] #44 Hose Clamps

[1] #28 Hose Clamp

[2] SS Button Head Bolts M6 x 16mm

[1] SS Button Head Bolt M6 x 10mm

[2] M6 Lock Nuts

[2] M8 Lock Nuts

[2] M8 Washers

TOOLS & SUPPLIES REQUIRED:

[1] T25 TORX Driver

[1] T30 TORX Driver

[1] 7mm Nut Driver

[1] Screwdriver

[1] 10mm Socket or Wrench

[1] 13mm Socket or Wrench

[1] 4mm Hex Key Wrench

[1] Needle Nose Pliers

[1] Degreaser or Contact Cleaner

[1] Clean Shop Rag

[1] Wire Cutters

1. JCW Only: Cut wire tie at valve cover breather hose to OE

turbo inlet hose. Pull out breather hose and remove rubber

collar. Then proceed to step #3.

2. S MODELS ONLY: Pull out valve cover breather hose from

OE turbo inlet hose.

3. Remove OE turbo inlet hose from MAF sensor. Use

screwdriver to loosen clamp at turbo inlet and at MAF sensor.

4. Disconnect electrical connector from Mass Airflow Sensor

(MAF).

5. Separate brake booster line holder from fresh air intake hose.

Use needle nose pliers to squeeze tabs and then push out

holder.

6. Remove T25 TORX screw located on passenger side of air

filter box and lift off. NOTE: There are [3] pin mounts that are

pushed into rubber grommet mounts on intake manifold, so

effort may be required to lift air filter box off of mounts.

7. Locate fresh air pipe that is attached to air filter box.

Disconnect fresh air pipe by rotating the 90° connection

counter clockwise and pulling pipe away from air filter box.

Remove air filter box from vehicle.

8. Remove MAF sensor from air filter box by removing [2] T30

TORX screws.

HI-FLOW INDUCTIONS KIT* – NM.658856 / B / C

[R55] MINI Cooper S 2008-10 / JCW Clubman 2009-11

[R56] MINI Cooper S 2008-10 / JCW Hardtop 2009-11

[R57] MINI Cooper S 2008-10 / JCW Convertible 2009-11

*For vehicles with Mass Airflow Sensor

Summary of content (2 pages)

PAGE 1
HI-FLOW INDUCTIONS KIT* – NM.658856 / B / C [R55] MINI Cooper S 2008-10 / JCW Clubman 2009-11 [R56] MINI Cooper S 2008-10 / JCW Hardtop 2009-11 [R57] MINI Cooper S 2008-10 / JCW Convertible 2009-11 *For vehicles with Mass Airflow Sensor PARTS INCLUDED: [1] Stainless Steel Intake Pipe Bracket [1] Aluminum or Carbon Fiber Intake Pipe [2] SS Button Head Bolts M6 x 16mm [2] M8 Washers TOOLS & SUPPLIES REQUIRED: [1] T25 TORX Driver [1] 10mm Socket or Wrench [1] Degreaser or Contact Cleaner 1. 2.
PAGE 2
16. Loosely install supplied #44 clamps onto both silicone hose ends, then install aluminum intake pipe into silicone turbo inlet hose first and then into MAF sensor hose. Adjust as necessary for clearance, paying close attention to clearance of silicone turbo inlet hose and coolant reservoir bottle. Tighten all clamps, use caution NOT to over tighten on Carbon Fiber Tube if being used. NOTE: Do not forget to tighten #28 hose clamp from Step 14. 12.