2.4GHz RF Modem User’s Manual Version 1.
User Manual Revision History Date 02/08/2007 Revision 1.0 Description Author Document Creation Szabolcs Zigovszki Proprietary & Confidential Version 1.
User Manual Table of Contents 1. Purpose and Scope of Document......................................................................... 1 2. Overview of the Radio Modem Hardware............................................................. 1 3. Operation of the Nivis Radio Modem ................................................................... 4 3.1. Getting started ...................................................................................................... 4 3.2 Read Calibration EEPROm ...
User Manual 1. Purpose of Document This document was created in order to provide to the user clear guidelines regarding the usage of the Nivis RF-P9-06-01-01 modem. 2. Overview of the Radio Modem Hardware The 2.4GHz Nivis Radio modem is an 802.15.4 wireless module that allows wireless communication using a standard asynchronous serial data stream. The pin-out of the Nivis radio modem is presented in the figure below. 1.90 in Trace PIFA 1.
User Manual The radio modem consists of three functional entities: 1. Transceiver section – processor, RF transceiver 2. RF section – BALUNs,RF PA, RF filter, RF switch 3. Non-volatile storage – Eeprom Power is supplied to the modem through pins 1 and 2. Pin 1 must be supplied with 3.3 Volts and powers the digital and RF functional entities of the modem. The modem has internal filtering circuitry to smooth out the supply voltage but it has no onboard regulators.
User Manual A table of the radio modem pins is provided below, describing the purpose and functionality of the pins and the max voltage range on the pins. Pin number Pin name Function of pin Nominal voltage 3.3 V Max voltage 3.6 V 1 VCC Voltage supply 2 3 4 5 GND RST BKGD KBD5 0V 3.3V 3.3 V 3.3 V 0V 3.6V 3.6 V 3.6 V 2.5V 3.3 V 3.3 V 3.6 V 3.3 V 3.
User Manual 3. Operation of the Nivis Radio Modem Communication with the NIVIS radio modem happens through serial port 2. The baudrate is set to be 19200, 8N1. 3.1. Getting started Open a terminal software on a serial port with the above settings and connect to the RF modem. Any command is single line followed by enter command. Format of command is: command param1 param2 … At startup pushing the enter key a few times is necessary until the reception of the prompt string.
User Manual - register ID: hex format d. Ex: getreg 00 5. Set Modem SPI Register a. Description: set value for a modem register (from page0) b. Command name: “setreg” c. Parameters: 2 - register ID: hex format - register vlaue: hex format d. Ex: setreg 20 80FF 6. Set Power Amplification value a. Description: set value for a modem PA power (not persistent value) b. Command name: “setpa” c. Parameters: 1 - PA value: hex format d. Ex: setpa FC 7. Set Modem Channel a.
User Manual 10. Put modem in IDLE state a. Description: put modem in IDLE state b. Command name: “idle” c. Parameters: None d. Ex: idle 11. Put modem in PULSE state a. Description: put modem in pulse PRBS9 state b. Command name: “pulse” c. Parameters: None d. Ex: pulse 12. Put modem in RX state a. Description: put modem in RX state b. Command name: “rx” c. Parameters: None d. Ex: rx 13. Put modem in RX echo state a.
User Manual d. Ex: txnomod 16. Put modem in TX modulated state a. Description: put modem in continuous TX modulated state b. Command name: “txmod” c. Parameters: None d. Ex: txmod 17. Read main info stored on EEPROM a. Description: displays SN, max PA power, and VRef stored on EEPROM b. Command name: “iic_read” c. Parameters: None d. Ex: iic_read 18. Clear EEPROM (except main info) a. Description: Clear EEPROM except main info b. Command name: “iic_erase” c. Parameters: None d.
User Manual - Max power hex format d. Ex: iic_setpa FF 22. Set output pin in lo a. Description: Set a pin as output and in lo state b. Command name: “outlo” c. Parameters: 1 - Pin definition: string: port and bit d. Ex: outlo A5 23. Set output pin in hi a. Description: Set a pin as output and in hi state b. Command name: “outhi” c. Parameters: 1 - Pin definition: string: port and bit d. Ex: outhi A5 4.
User Manual The Nivis RF Module 6.0 has been certified per FCC Part 15 rules for integration into products without further testing or certification. To fulfill the FCC certification requirements the OEM of the Nivis RF Module must ensure that the information provided on the Nivis RF Module 6.0 Label is placed on the outside of the final product. The Nivis RF Module 6.0 is labeled with its own FCC ID Number.
