User's Manual

UsermanualforD2Scharger

Specifications

Input:    AC100‐240V50/60Hz 30W 

DC12V500mA

Output:   4.35V±1%/4.2V ±1%/3.7V ±1%/1.48V ±1%  1.0A(max)

Compatiblewith:

Li‐ion/IMR/LiFePO4: 

10340,10350,10440,10500,12340,12500,12650,13450,13500,13650,14350,14430,14500,14650,16500,

16340(RCR123),16650,17350,17500,17650,17670,18350,18490,18500,18650,18700,20700,21700,22500,

22650,25500,26500,26650

Ni‐MH(NiCd):AA,AAA,AAAA,C,D



Features

·Capableofchargingtwobatteriessimultaneously

·Eachbatteryslotcontrolsandchargesindependently

·Upto1Achargingspeedinasingleslot

·Batterytypeandchargingcurrentcanbesetmanually

·Automaticselectionofconstantcurrent,constantvoltage,dV/dtchargingmodetochargethebattery

·AutomaticIdentificationofLithiumIonBatteryandNi‐H/Ni‐CDRechargeableBattery

·WithanLCDdisplay,thebatterytypeandcharginginformationcanbedisplayed

·ComeswithBluetoothmodule,canconnecttothephonetoviewbatterytype,charginginformationandset

batterychargingvoltageandchargingcurrent

·Automaticallydetectsbatterypowerstatusanddisplayschargingprogress

·Reversepolarityprotectionandshortcircuitprevention

·Li‐ionbatteryrestoration

·Overtimechargingprotection



Operating Instructions

Connect to powersource: connecttheSC2to an external power source(wall outlet,caradapter. etc.)viaits

powercord.ThescreenwilldisplaythelasttwoBluetoothIDofthecharger.

Insert batteries: The SC2 features two independently controlled charging slots. Insert batteries of supported

typesintoeachslotaccordingtothepolaritymarksontheslot.

Smart charging:TheSC2 canchoose chargingcurrentsbasedon intelligentdetectionabout batterytypesand

capacities.Manualchargingcurrentselectionisalsoavailable.TheSC2iscompatiblewith:

3.7VLi‐ionrechargeablebatteries

3.8VLi‐ionrechargeablebatteries

1.2VNi‐MH/Ni‐Cdrechargeablebatteries

3.2VLiFePO4batteries

Whenthebatteryisinstalled,thechargerwillautomaticallydisplaythebatterytypeandcharginginformation

andenterthechargingstate. 

Alarmfault：Ifthebatteryfailureorshortcircuitisnotrechargeable,thescreendisplays"EEEE".

chargingcurrent ：Thedefaultchargingcurrentofthischargeris1Awhenchargingasinglebatteryand500mA

whenchargingtwobatteriesatthesametime. 

PAGE 1
User manual for D2S charger Specifications Input : AC 100‐240V 50/60Hz 30W DC 12V 500mA Output: 4.35V±1% / 4.2V ±1% / 3.7V ±1% / 1.48V ±1% 1.
PAGE 2
Key function description: Charging mode: Short press SLOT key: when charging normally, short press SLOT key to switch channel display; Long press SLOT key: when charging normally, long press SLOT key to query the last two Bluetooth ID of the charger; when there is IMR battery in overdischarge state, long press SLOT key can enter activation mode. Short press MODE key: when charging normally, short press mode key to switch display battery charging current and the amount of electric charge has been charged .
PAGE 3
The charger will independently calculate the battery charging time for each slot, and when the charging time exceeds 10 hours, the charger will force the charging output of the tank to be turned off, and the full electric mark will be displayed. And the heating explosion phenomenon caused by the battery quality problem is effectively prevented.
PAGE 4
- Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.