Quick Guide

Nikon camera bulb mode
Canon camera bulb mode
Sony camera bulb mode
The NiSi remote control instruction
Step 1
INSTALL APP
Search “ NiSi ND Calculator“ in Apple’s app Store or Android Market.
Step 2
POWER ON
Insert the 3.5mm CABLE into the remote control. The remote control
will power on automatically. The power LED indicates red for 3
seconds initially. When it flashes blue, this indicates that the control
is powered on. Connect the cable to the camera.
1. Take off orange silicon rubber case.
2. Take off the orange battery protector.
3. Replace the new battery with the negative (-) face up.
4. Replace the orange silicon rubber case
Tips: Please check the battery if the power light off. Quick
guide to replacing the battery:
1. The maximal exposure time for this App is 255mins.
2. The minimum exposure time for the App is 1/100 sec
3. The bulb mode minimum exposure time is 1/10 sec
4. The App can calculate the exposure time without the
remote control but it can’t control the camera exposure
time.
Tips:
Tip: Choose the ND filter notation you are comfortable with as
well as exposure increments.
Set your camera to bulb mode after everything has been set up.
The App will initiate your long exposure which you can cancel
at any time.
Step 4
SET UP
First, choose the ND filter density you are planning on using. Set up
your basic shutter speed and exposure compensation. The App will
calculate the long exposure shutter speed based on the density of the
ND filter you have chosen.
Step 3
CONNECTION
Turn on your phone’s Bluetooth and start up the app” NiSi ND
Calculator“.
Select the Bluetooth device ”nisioptics”
Step 5
DISCONNECTION
Select “back” or “exit” on the App. Once the long exposure has
commenced, it will continue even the phone is powered off or you
have exited the App.
Step 6
Power off
Remove the cable
You can change the name of Bluetooth.
Once the application has connected to the device, you will be brought
to a log in page.
1. Exit the App
2. Turn off bluetooth for at least 30 seconds
3. Turn on Bluetooth
4. Restart the App
Tip: Follow these steps of the Bluetooth device cannot be
discovered.
1 2
4
1 2
1
1
2
2
3
1
2 3
1
2 3
1
2 3
1
2 3
1
1
1
1
1
2
2
2
3
3
Nikon Cable
Release Interface
Canon Cable
Release Interface
Sony Cable
Release Interface
Tip: When you exit the App and confirm disconnection, you
will need to reconnect the Bluetooth device.
Tip: The remote control will power off if Bluetooth connection
has been idle for 30 mins. You will need to remove the cable
release and reinsert the cable to continue using this device.
FCC compliance statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
Tip: You can choose “ skip “ log in the main page. The App can
calculate exposure times without connection to the remote.