ASSEMBLY INSTRUCTIONS English.........................2 Français........................
Included Parts Charger AC Adapter Locator Magnets Charging Location Sticker Locator Template Double-Sided Adhesive Sticker Cable Clips Mounting Screws Tools Required Pencil 2 Drill with #2 Philips Head Driver Bit
NOTE Charger does not work at close range. The work surface thickness must be at least 15mm (0.6”) and no more than 30mm (1.2”). STEP 1: Choose a charging location on the desk, making sure there is space beneath for the charger. Clean and dry the surface before placing the charging location sticker. Remove adhesive backing and place the charging location sticker on work surface in the desired location. STEP 2: Place a stack of 2 included magnets on the power symbol in the center of the location sticker.
STEP 3: Beneath the work surface, use the third magnet to find the location of the upper magnets. When they are aligned, adjust the position to make sure the upper magnets are still centered on the sticker. STEP 4: Center the locator template on the lower magnet and hold the template against the work surface, making sure to not move the magnet. STEP 5: Using a pencil, trace around the edge of the template, then remove the template and magnets.
STEP 6: Align the charger with the pencil marks. The small indicator LED should face the front and the power socket should face the rear. Ensure that the “THIS SIDE UP” faces upwards. Attach the charger to the work surface with the included screws. NOTE: If mounting to a surface that cannot be screwed into, such as glass, use the included double-sided adhesive sticker to mount the charger. Clean and dry both surfaces and remove the “THIS SIDE UP” sticker before adhering.
STEP 7: Plug in power cable and AC adapter. If needed, cable clips can be used to manage the power cable. LED Behavior • Power on: green light flashes 2 times • Charging: green light flashing (1 second intervals) • Abnormal / Error / FOD (Foreign Object Detection): red light flashing (0.5 seconds intervals) until the Foreign Object is removed or the device is power cycled.
Product Information Product Name: NeatCharge Model #:WE9012C-X Input: 100-240VAC 50/60Hz 24V 1A Max Wireless Output Power 10W Charging Distance: 15mm to 30mm (0.6”-1.2”) Qi compatible devices Weight: 7.
Product Information (continued) FCC Statement This device complies with Part 15 and Part 18 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
INSTRUCTIONS D’ASSEMBLAGE Amérique du Nord : +1 800 400-0625 Europe : + 353 (0)1 858-0910 Asie pacifique : + 852 2581-0570 9
Pièces incluses Chargeur Adaptateur d'alimentation Aimants de positionnement Autocollant de positionnement du chargeur Gabarit de positionnement Autocollant double face Attaches-câbles Vis de montage Outils nécessaires Crayon 10 Perceuse avec embout cruciforme no 2
REMARQUE Le chargeur ne fonctionne pas à courte portée. La surface de charge doit avoir une épaisseur de 15 mm (0,6 po) à 30 mm (1,2 po). ÉTAPE 1 : Choisissez un emplacement de chargement sur le bureau en vous assurant qu’il y a de l’espace en dessous pour le chargeur. Nettoyez et séchez la surface avant de placer l’autocollant d’emplacement du chargeur. Retirer le dos adhésif et placer l’autocollant de positionnement du chargeur à l’endroit choisi sur la surface de charge.
ÉTAPE 3 : Placer le troisième aimant sous la surface de charge, de façon à ce qu'il soit aligné avec les deux aimants du haut. Une fois fait, ajuster la position des aimants pour vous assurer que les aimants supérieurs sont toujours au centre de l'autocollant. ÉTAPE 4 : Centrer le gabarit de positionnement sur l'aimant inférieur et le tenir sur la surface de charge en veillant à ne pas déplacer l'aimant.
ÉTAPE 6 : Aligner le chargeur sur le tracé. Le petit voyant DEL doit être sur le devant et la prise d'alimentation à l'arrière. Assurez-vous que la mention «THIS SIDE UP» est bien orientée vers le haut. Fixer le chargeur à la surface de charge à l'aide des vis fournies. REMARQUE : pour installer le chargeur sur une surface dans laquelle il est impossible de visser, comme le verre, utiliser l'autocollant double face.
ÉTAPE 7 : Brancher le câble d'alimentation et l'adaptateur d'alimentation. Au besoin, utiliser les attaches-câbles pour retenir le câble d'alimentation. Voyant DEL • Sous tension : voyant vert qui clignote deux fois • En charge : voyant vert qui clignote à intervalle d'une seconde • Mauvais fonctionnement, erreur, détection d'un corps étranger : voyant rouge qui clignote à intervalle de 0,5 seconde jusqu'à ce que le corps étranger soit retiré ou que l'appareil soit redémarré.
Information sur le produit Nom du produit : NeatCharge Numéro de modèle : WE9012C-X Entrée : 100-240 VCA, 50-60 Hz, 24 V, 1 A Puissance de sortie sans fil maximale : 10 W Distance de recharge : de 15 à 30 mm (de 0,6 à 1,2 po) Pour les appareils qui satisfont la norme Qi Poids : 225 g (7,94 oz) Température de fonctionnement : de 0 °C à 35 °C (de 32 °F à 95 °F), humidité de 10 à 90 % Température d'entreposage : de -20 °C à 80 °C (de -4 °F à 176 °F), humidité de 5 à 95 % Numéro d'identification de la FCC ID: 2
Information sur le produit (suite) Déclaration de la FCC Cet appareil est conforme aux parties 15 et 18 des règles de la FCC. Son fonctionnement est sujet aux deux conditions suivantes : (1) l'appareil peut causer un brouillage préjudiciable, et (2) il doit accepter tout brouillage reçu, incluant celui qui pourrait entraîner son mauvais fonctionnement.