Assembly Instructions

ManualsBrandsNingbo Pdlux Electronic Technology ManualsElectronicsMicrowave Sensor

Part NO. Country Frequency Comments

PD-V10-501

PD-V10-502

UK 10.587 GHz (5V)

Belgium, Holland, Italy 10.525 GHz (5V) Meets RED Directive

USA 10.5-10.55 GHz (5V) FCC-ID

PD-V10-301

PD-V10-302

UK 10.587 GHz (3V)

Belgium, Holland, Italy 10.525 GHz (3V) Meets RED Directive

Environmental Characteristics

Key Features

• Low Cost

• High Sensitivity

• Patch Antenna

• Low Power consumption

• 3V and 5V versions available

• RoHS compliant

Applications

Coverage Pattern

• Intrusion Alarms

• Automatic Door Openers

• Presence Sensing

X-Band Doppler Motion Detector Unit

Model:PD-V10-G5

The Microwave Solutions PD-V10-G5 Motion Detector Unit is a miniature X-Band microwave transceiver that

utilises the Doppler shift phenomenon to "sense" motion.

The unit, housed in a metal can, features a dielectric resonator stabilised oscillator, which provides stable

operation over a broad temperature range in either CW or low duty cycle pulse mode and an integrated

homodyne receiver for enhanced sensitivity and reliability.

This module family is available with either a +5v or +3v supply voltage.

Operation

The basic principle of operation consists of detecting the frequency shift between a transmitted and a received signal

reflected back from a moving object within the field of view of the unit.

The unit produces a low level output signal which can be amplified and processed to provide an audible or visual alarm

signal and employs low cost surface mount manufacturing techniques which are field proven as being rugged and

reliable.

Available Modules

Electrical Characteristics

Transmitter

Antenna : standard Mechanical Characteristics

Pulse Mode Operation

Frequency See table over

Power Output (Min.) 12 dBm EIRP

Operating Voltage +5 V ± 0.25 V

+3 V ± 0.15 V

Operating Current (CW) 25mA (max)

20mA (typ)

Harmonic Emissions <-30dBm

Average Current (5% DC) 1 mA typ.

Pulse Width (Min.) 5 µsecs

Duty Cycle (Min)

Pulse Repetition Frequency

2-4 KHz

Receiver (Bandwidth 1Hz~3KHz)

Sensitivity (for a 10 dB S/N ratio) -84 dBm

Noise (measured in a 3Hz to 80Hz bandwidth) < 30 µV

Gain 5 dBi

-3 dB Beamwidth

E Plane 50°

H Plane 60°

Weight 4 g

Pin header connectors 2.54mm spacing X3

RoHS Compliant

Power/Temp. Coefficient (over operating temp. range) 3 dB

Frequency/Temp. Coefficient (over operating temp. range) 6.5 MHz

Operating Temperature -20° C to +70° C

www.pdlux-solution.com www.pdlux.com Tel: 86-574-83008608(20 lines)

9mm

Xmm

27mm

17.6mm

+5VIF

GND

Horizontal

Vertical

NOTES

The strength of the sensor's output （detection range）depends on the Signal to Noise Ratio.

Higher or lower than the nominal operating temperature, the sensor can also work, but the performance will be reduced.

To avoid damage to the devices, care should be exercised during handling. Proper Electrostatic Discharge (ESD)

precautions should be observed at all stages of storage, handling, assembly, and testing.

Summary of content (5 pages)

PAGE 1
X-Band Doppler Motion Detector Unit Model:PD-V10-G5 Key Features • Low Cost • Low Power consumption • High Sensitivity • 3V and 5V versions available • Patch Antenna • RoHS compliant Transmitter See table over Average Current (5% DC) 1 mA typ. Power Output (Min.) 12 dBm EIRP Pulse Width (Min.) 5 µsecs Operating Voltage +5 V ± 0.25 V Duty Cycle (Min) 1% +3 V ± 0.
PAGE 2
Regulatory Module Integration Instructions 2.2 List of applicable FCC rules This device complies with part 15.245 of the FCC Rules. 2.3 Summarize the specific operational use conditions This module can be used in household electrical appliances as well as Intelligent switch , Wall-hung switch equipments. The input voltage to the module should be nominally 3.0 to 5.25 VDC ,typical value 5VDC and the ambient temperature of the module should not exceed 70℃.
PAGE 3
2.7 Antennas Module contains one PCB antenna. No additional external connectors. 2.8 Label and compliance information The outside of final products that contains this module device must display a label referring to the enclosed module. This exterior label can use wording such as: “Contains Transmitter Module FCC ID: 2AIWW-PD-V10-G5”,or “Contains FCC ID: 2AIWW-PD-V10-G5 ”, Any similar wording that expresses the same meaning may be used. 2.
PAGE 4
c) If the investigation indicates a compliance concern the host product manufacturer is obligated to mitigate the issue. Host products using a modular transmitter are subject to all the applicable individual technical rules as well as to the general conditions of operation in Sections 15.5, 15.15, and 15.29 to not cause interference. The operator of the host product will be obligated to stop operating the device until the interference has been corrected 2.
PAGE 5
Operating the host product When testing the host product, all the transmitters must be operating.The transmitters can be enabled by using publicly-available drivers and turned on, so the transmitters are active. In certain conditions it might be appropriate to use a technology-specific call box (test set) where accessory devices or drivers are not available. When testing for emissions from the unintentional radiator, the transmitter shall be placed in the receive mode or idle mode, if possible.