Installation Instructions

ManualsBrandsNINGBO LONGMARCH IMPORT & EXPORT ManualsElectronicsWIRELESS DOORBELL

Wireless Doorbell

With Motion Sensing LED Security Light

BATTERY INSTALLATION

PRODUCT INSTALLATION

PAIRING

RECEIVER & DOORBELL SET-UP

Figure A

Receiver - Front

Figure B

Receiver - Rear

Doorbell Receiver

Doorbell Button With LED Light

Screws

Dry Wall Anchors

Set of Hook & Loop Adhesives

QuantityPart

Screw

Dry Wall Anchor

Figure C

Doorbell Button- Front

Figure E

Doorbell Button - Rear

Volume

Chime

Selection

Pairing Button

Pairing

Button

Battery

Compartment

LED

Security Light

Motion

Sensing On/

Off Switch

Battery Cover

Screws

RECEIVER – Remove the battery cover located on the rear of the Receiver (Figure B). Install 3 AAA batteries according to the polarity indicated in each battery slot. Replace

the battery cover. For best result, use alkaline batteries.

DOORBELL – The battery compartment is located on the rear of the Doorbell (Figure C). Use a Philips head screwdriver to remove the two screws holding the cover in place.

Remove the cover and install 3 AAA batteries according to the polarity indicated in each battery slot. Replace the cover, reinstall the screws and tighten. For best result, use

alkaline batteries.

IMPORTANT

Your Receiver and Doorbell have pre-installed batteries. Remove the battery insulator strips from both doorbell receiver and doorbell button battery compartment before

ﬁrst use.

Screws, drywall anchors and hook and loop connectors are included with your product. You can choose to use any of the attachments, but if possible, use of a screw is

preferable. The Receiver and Doorbell can connect wirelessly up to 100’, but distances may vary based on the number and composition of walls between the Receiver and

Doorbell.

Your Receiver and Doorbell are not paired when ﬁrst removed from packaging. To pair, press and hold the Pairing Button located on the right side of the Receiver for 3

seconds (Figure B). When you press the button to pair, the doorbell tone will ring. After pairing, push the button on the Doorbell to ensure successful pairing. If the Receiver

does not ring, repeat this step again.

Choose the locations of both your Receiver and Doorbell. Before installing, test the units by placing in their approximate locations and ringing the Doorbell. If the receiver

does not ring when you do so you may need to move them nearer to each other. Your Doorbell button is weather resistant but should NOT be placed in a location that may

result in excessive exposure to water.

Once you have established locations the Doorbell and Receiver function properly, mount them to the locations. It is best to mount each on a ﬂat surface such as a wall or

door-frame. If you use screws, install the screws included in the proper locations leaving approximately ¼” of the screw and head protruding from the wall. Slide the bayonet

hanger located on the rear of the Receiver and Doorbell over the protruding screw head (Figure B). If the surface of the wall you will be mounting on is drywall use the

included drywall anchors to install your screw.

If you will be using the hook and loop closure to mount your Doorbell or Receiver, clean the surfaces of where you will be applying each tab. Remove the paper covering the

adhesive located on the reverse sides of the hook and loop. Mount one to the ﬂat surface and its mate to the device. The piece that is mounted to the unit should be stuck to

the battery cover. Once hook & loop closures are in place, ﬁrmly press the device to the ﬂat surface to mount.

Thanks for purchasing another Flipo® product intended to make life a little easier. FLIPO® offers a wide variety of unique products of the highest quality. To ensure the

maximum performance of your product, please read and save these instructions.

Summary of content (2 pages)

PAGE 1
Wireless Doorbell With Motion Sensing LED Security Light Thanks for purchasing another Flipo® product intended to make life a little easier. FLIPO® offers a wide variety of unique products of the highest quality. To ensure the maximum performance of your product, please read and save these instructions.
PAGE 2
FUNCTIONS Doorbell Button - PIR Activated Light Each Doorbell Button includes a PIR Sensor and COB LED light. When activated by motion the LED will illuminate the Doorbell’s push button. PIR sensors ONLY function in darkened environments - the light will not turn on needlessly during daylight hours. To activate, simply slide the switch located on the left of the Doorbell up to the ON position (Figure E). When activated the light will illuminate for approximately 20 seconds or until movement ends.