User Manual

ManualsBrandsNINGBO DONGXING ELECTRIC ManualsElectronicsLED Lamp

Table Of Contents

Caution:

This device complies with Part 15 of the FCC Rules /

Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,

and (2) this device must accept any interference

received, including interference that may cause

undesired operation.

Le présent appareil est conforme aux CNR d'Industrie

Canada applicables aux

appareils radio exempts de licence. L'exploitation est

autorisée aux deux conditions

suivantes : (1) l'appareil ne doit pas produire de

brouillage, et (2) l'utilisateur de

l'appareil doit accepter tout brouillage radioélectrique

subi, même si le brouillage est

susceptible d'en compromettre le fonctionnement.

Changes or modifications not expressly approved by

the party responsible for compliance could void the

user's authority to operate the equipment.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful

interference in a residential installation. This

equipment generates uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the

Summary of content (14 pages)

PAGE 1
Caution: This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
PAGE 2
interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.
PAGE 3
To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installées doivent être situées de facon à ce que la population ne puissey être exposée à une distance de moin de 20 cm.
PAGE 4
Login There are two methods to login for new users: Account login and Skip login 1.1 Account login Open the App and make sure the Bluetooth is open. When register account, users need to click on “Register account” and input Mailbox, account name and password.
PAGE 5
Devices 1.Devices: Click“Devices”→“Add device”→ “next”→ to add devices.
PAGE 6
2.Once devices connected successfully, can find the devices in the device list. User can control on/off by pressing the icon on the right of the device list. Users can edit the device as user preferred by clicking the icon on the left of the device list, such as rename, setting for brightness, CCT and colors.
PAGE 7
Rooms 1、Click“Rooms”to enter the page 2、click “+” 3、Input Room name and insert Room picture 4、Choose the device to be added in this Room, and then click“done”.
PAGE 8
Scenes 1、Click the “ Scenes” and enter the page, then default scenes “ Away from home ” , “ Back home ” and “ Rest ” can be edited. Click the blank area at the right of the scene can perform it. 2、Click“scenes”on homepage, and click “+” in the middle to add new scenes or click “+” at the top-right corner and then click “Add scenes” on pop-up page to enter. Input scene name in this page and choose the devices, then click “next ” to edit the action of the devices.
PAGE 9
Home Home page: show scenes, all group, rooms and connected devices.
PAGE 10
Schedule task 1、Click “ Schedule task ” on setting page, and then click “Create a task” to enter next page, which can creat devices, rooms and scene tasks. Take create a scheduled task as an example in the figure below.
PAGE 11
General Settings Click gear button to enter into setup page. 1、Reset password：Click to reset the account password. 2、Scheduled task：Create a scheduled task and support on multi-devices operation. 3、Firmware upgrade：Update the devices to the latest version. 4、Version information: Find the current APP software Version. 5、Operation instructions：Know more about APP operation. 6、Reset account: Reset the account to delete all connected devices. 7、About us：Know more about DongXing.
PAGE 12
Reset 1、Manual reset: make sure that the device is on for more than 5 seconds. Turn off the device, and repeat on and off for three times (every time stay off for 1-2 seconds), the restoration of the device happen in the forth time. For RGBW type, the device will flash red, green, blue, white, red, green and white alternately in turn until keep on after reset. For Tunable White type, the device will flash white-yellow, white-yellow alternately until keep on after reset.
PAGE 13
Firmware upgrade 1、Click “ firmware upgrade ” on setting page. If the device firmware is the latest version as shown in the figure, users do not need to upgrade it.
PAGE 14
2、Click “ firmware upgrade ” on setting page. When the device can upgrade, click the red “ upgrade ” button and upgrade the device follow the instruction.