User's Manual

ManualsBrandsNINGBO DIYA ELECTRIC APPLIANCE ManualsElectronicsRemote Control Transmitter

Draft RFK instruction

Wireless RF Remote Control System DR-1755

Hand Held Transmitter DR-1698 and Plug-in Receiver DR-1693

Feature:

This wireless Radio Frequency (RF) control is an easy, convenient way to add switched outlet

convenience without any wiring or electrician needed.

The invisible RF signal passes through walls, doors, ceilings, floors and even around corners.

Simply plug the desired appliance into the receiver and the receiver into any outlet.

The transmitter is designed to look just like an actual switch and Switch plate and mounts to any

surface with the enclosed screws. A press of the transmitter’s toggle switch turns whatever

you’ve plugged into the receiver on or off - just like a hardwired switch and outlet!

CAUTION

1: The total load of appliances connected to the Plug-in Receiver should not exceed 1875 Watts or

15 Amps resistive, or 625Watts or 5 Amps tungsten.

2: Do not use Plug-in Receiver to control appliance loads that may be dangerous to turn on

remotely (i.e. power tools).

3: The Plug-in Receiver must be located within 100 feet Transmitter.

Step1: Remove battery cover of wall transmitter on back side. Remove plastic battery tab by

gently pulling it from the battery compartment (this tab isolates the battery until it’s ready for

use and insures that you’ll have a fresh battery). Reassemble battery cover.

Step2: Pairing .Your transmitter and receiver had been paired before shipped ,if you would like to

replace any of receiver/transmitter ,please go to “Step 2A” procedure .if not ,please go to Step 3

Step2A: Plug the Receiver into any standard grounded 120 Volt outlet being careful to match the

wide blade of the Receiver with the wide slot on the outlet. Fully insert.

Step2B: Remove paired

1. Press and hold the power button for 5 seconds until the LED indicator begins to flash slowly.

2. Press and hold the power button for an additional 5 seconds until the LED indicator begins to

flash rapidly .

3. Press the power button once to confirm to remove all paired transmitter from your receiver

Step2C: Pairing transmitter and receiver. pairing will be saved for 1 year without power supply

1. Our remote control units include a unique pairing feature that allows you to control multiple

receivers from the same transmitter ,or to control same receivers from multiple transmitter .

2. Press and hold the power button on the receiver for 5 seconds until the LED indicator begins

to flash slowly, indicating pairing mode has been activated .

3. Press “ON” button ,then “OFF” button on your transmitter to complete the pairing process .

Repeat Step2A-2C to pairing multiple transmitter or receiver.

Step2D: unplug receiver.

Step3: Plug your light/appliance into the outlet on the Receiver being careful to match the wide

blade of the light/appliance (if equipped) with the wide slot on the outlet.

Step4: Plug the Receiver into any standard grounded 120 Volt outlet being careful to match the

Summary of content (4 pages)

PAGE 1
Draft RFK instruction Wireless RF Remote Control System DR-1755 Hand Held Transmitter DR-1698 and Plug-in Receiver DR-1693 Feature: This wireless Radio Frequency (RF) control is an easy, convenient way to add switched outlet convenience without any wiring or electrician needed. The invisible RF signal passes through walls, doors, ceilings, floors and even around corners. Simply plug the desired appliance into the receiver and the receiver into any outlet.
PAGE 2
wide blade of the Receiver with the wide slot on the outlet. Fully insert. Step5: Press switch to determine if your light/appliance turns on and off at the distance you desired. Install you Wall Transmitter at the location where you wish to use it, by two key holes on back side of transmitter. Note 1: If your light/appliance does not respond try relocating the transmitter or receiver.
PAGE 3
For indoor use only Transmitter: DR-1698: Battery: 12Volt, 433.92MHz FCC ID: 2AC2CDR-1698 For indoor use only. One-Year Limited Warranty: product will be free from defects in materials and workmanship for a period of one year from the date of purchase. Additional details are available at www.amertac.com. Prop.65 WARNING: This product contains chemicals known to the State of California to cause cancer and/or birth defects or other reproductive harm.
PAGE 4
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.