Use and Care Guide

THANK YOU
USE AND CARE GUIDE
WIRELESS INDOOR/OUTDOOR
REMOTE CONTROL SWITCH
WARNING
:
The device must be mounted in a vertical position
with the receptacle facing downward and with the receptacle at
least 2 ft. above the ground level to prevent water immersion.
RATINGS
125 VAC, 60 Hz
15 A General Purpose
1000W Tungsten
Installation Instructions
Product Description
Product Description
Safety Information
1
2
3
1. Power indicator light:
The power indicator light
indicates that the receiver is on.
2. Outlets:
The two outlets located on the
bottom of the receiver allows
the user to plug an array of
devices into it. Plug the lights or
devices to be controlled by the
remote into one of the outlets.
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
¨ Reorient or relocate the receiving antenna.
¨ Increase the separation between the equipment and the receiver.
¨ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
¨ Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation of the device.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
Store indoors when not in use.
Operating Instructions
¨
To activate the receiver, press the “ON” button of the remote control.
The green LED of the remote control will illuminate momentarily and the
LED of the receiver will remain illuminated.
¨
To turn the receiver OFF, press the “OFF” button of the remote control.
The LED on the receiver will shut off.
1
Using the remote control
¨
Plug the receiver into an outlet. Plug the devices to be controlled into
the outlets on the receiver.
noituloSmelborP
The lights do not turn on and
off via remote control.
Troubleshooting
Confirm remote operation after replacing
batteries.
Remote control:
¨ ON: When the on button is
pressed, it will override the
receiver’s current program
to on function.
¨
OFF: When the off button is
pressed, it will override the
receiver’s current program
to off function.
¨
Remote indicator light: The
LED light indicates that the
ON or OFF button is being
pressed.
Maintenance
2
Replacing the battery
¨
¨
Remove the old battery and place a new DC 3V CR2032 battery into
the battery compartment, correctly observing the polarity indications (+/−)
inside the battery compartment.
¨
¨
Dispose or recycle spent/discharged batteries in compliance with all
applicable laws. For detailed information, contact your local solid waste
authority.
15 A Resistive
NOTE: This product is suitable for outdoor use and use in damp
locations.
¨ Mount the receiver onto a wall near a grounded electrical outlet.
¨ Insert a nail or screw (not included) into the mounting surface. Nail or
screw head must extend at least 3/16 in. out from the wall. Hang the
receiver from the slot on back of the unit onto the nail or screw. Plug the
power supply cord of the receiver into the outlet.
¨ Plug the device cord into any of the two receptacles at the bottom of the
receiver.
The lights do not turn on, even
when the power indicator light
indicates that the receiver is on.
Ensure the lights are functional by
plugging them directly into an outlet.
Be sure that the lights are in the “ON”
position if they have their own switch.
Be sure that the outlet that the receiver
is plugged into is active.
3.
WARNING
:
Do not mutilate or place the battery in a fire. The
battery may burst or release toxic materials. Do not short circuit
or reverse polarity as this may cause burns.
We appreciate the trust and confidence you have placed in
Defiant through the purchase of this outdoor wireless remote control.
Visit us online to see our full line of products available for your home
improvement needs. Thank you for choosing Defiant!
Remote does not turn the
device on or off.
Model: YLT-42BC
1/3HP
Receiver and transmitter need to be re-synched.
Replug the reciever into a properly gounded outlet
untill the green indicator flash on the reciever,then
and within 10 seconds,
press the ON button within 2 seconds.
press the OFF button
Unsrew the screw on the battery compartment cover from the back of
the remote control.
Replace the battery compartment cover and locking the screw.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This device generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
device does cause harmful interference to radio or television reception, which can be determined
by turning the device off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the device and receiver.
--Connect the device into an outlet on a circuit different from that to which the receiver is
connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions: (1) This device may not cause interference. (2) This device must accept any
interference, including interference that may cause undesired operation of the device.
Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS)
d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis
aux deux conditions suivantes : (1) Cet appareil ne doit pas causer d'interférences. (2) Cet
appareil doit accepter toutes les interférences, y compris celles susceptibles de provoquer un
fonctionnement indésirable de l'appareil.