Instruction Manual

1.
•
•
•
2.
•
•
3.
•
•
•
**
MADE IN CHINA
INSTRUCTIONS:
Charging the Powerbank:
Charge the powerbank fully before usage.
Connect the provided charging cable to a
power source and to the micro USB port
on the powerbank(6). Or your own Type C
cable to the Type Input Port (4).
Once connected the LED Indicator will
HITE when charging, once
fully charged LED will turn WHITE.
Charging mobile phones and other
electronic devices:
Connect the charging cable to your mobile
phone/device using the appropriate
connector. Connect the USB part of the
cable into either USB Output(3 or 5). LED
Indicator will illuminate when charging.
Remove the USB cable from your mobile
device when it is fully charged.
Wireless Charging Function:
Press the Powerbank ON/OFF button(7) to
turn on the wireless charging function, LED
indicator near power button will flash green
for one time and turn on.
Place wireless charging supported mobile
device on the charging surface/suction
pad, the green LED will be blinking flash
when device is charging.
Phone will begin to charge automatically.
Note: When wireless charging, if the LED
NOT a wireless charging device or there is
an object between the device and charging
surface interfering with the charging.
Mare 8000 mAh Suction
Wireless Power Bank
Instruction Manual
AST-WR070
1 x 8000 mAh Wireless Powerbank
1 x USB to Micro-USB Cable
1 x Instruction Manual
Battery: 8000mAh/3.7V/29.6Wh
USB Output 1/2: 5V/2A Max
Wireless Output: 5W
Type-C input: 5V/2A
Micro-USB Input: 5V/2A
ON/OFF Button: Press once to view the
remaining power capacity.
1.
2.
3.
4.
5.
6.
7.
8.
•
•
•
•
•
•
Wireless Charging Surface
Suction Pad
USB Output 1
Type-C Input Port
USB Output 2
Micro-USB Input Port
ON/OFF Button
LED Indicators
What’s included:
Features:
LED Indicators
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FCC Warning Statement
wireless charger, and lead to overheating.
Please remove attachments from the phone
before charging on this device.
WARNING-When using this product, basic
precautions should always be followed:
Read all the instructions before use.
Never store or use this product in
temperatures below 32°F (0°C) or above
115°F (45°C).
Do not overcharge your phone. The
unit may become hot under excessive
use. Remove your phone once it is fully
charged. Never charge your phone for
more than 7 hours at a time.
The unit will only achieve full performance
after 2 or 3 completed charge and
discharge cycles.
To reduce the risk of injury, close
supervision is required when the product is
used near children.
Do not expose the device to moisture.
Do not use the device in excess of its
output rating. Overload outputs above the
Do not use the device if damaged or
explosion or risk of injury.
Do not disassemble the device. For
professional. Incorrect reassembly may
or temperatures above 104°F (40°C) may
result in explosion.
To ensure product safety, ensure that
identical replacement parts.
Attachments on the back of your phone
•
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
SAFETY PRECAUTIONS:
The distance between user and products should be no less than 20cm