User's Manual

ManualsBrandsNielsen-Kellerman ManualsElectronicsWi-Fi & Bluetooth Internet of Things Module

U.S. FCC Statement

PN: 621632

PMN: KMET6000W

FCC ID: 2ADAJ-KMET6000W

The device complies with KDB 996369 DO3 OEM Manual v01. Below are integration instructions

for host product manufacturers according to the KDB 996369 DO3 OEM Manual v01.

List of Applicable FCC Rules

FCC Part 15 Subpart C 15.247 & 15.209

Specific Operational Use Conditions

The module has WiFi, BR, EDR and BLE functions.

• Operation Frequency:

- WiFi: 2412 ~ 2462 MHz

- Bluetooth: 2402 ~ 2480 MHz

• Number of Channels:

- WiFi: 12

- Bluetooth: 40

• Modulation:

- WiFi: DSSS; OFDM

- Bluetooth: GFSK; π/4 DQPSK; 8 DPSK

• Type: External antenna connector

• Gain: 2.33 dBi Max

The module can be used for loT applications with a maximum 2.33 dBi antenna. The host

manufacturer installing this module into their product must ensure that the final composite

product complies with the FCC requirements by a technical assessment or evaluation to the FCC

rules, including the transmitter operation. The host manufacturer has to be aware not to provide

information to the end user regarding how to install or remove this RF module in the user’s

manual of the end product which integrates this module. The end user manual shall include all

required regulatory information/warning as show in this manual.

Limited Module Procedures

Not applicable. The module is a single module and complies with the requirement of FCC Part

15.212.

Trace Antenna Designs

Not applicable. The module has its own antenna, and does not need a host's printed board

microstrip trace antenna, etc.

Summary of content (7 pages)

PAGE 1
U.S. FCC Statement PN: 621632 PMN: KMET6000W FCC ID: 2ADAJ-KMET6000W The device complies with KDB 996369 DO3 OEM Manual v01. Below are integration instructions for host product manufacturers according to the KDB 996369 DO3 OEM Manual v01. List of Applicable FCC Rules FCC Part 15 Subpart C 15.247 & 15.209 Specific Operational Use Conditions The module has WiFi, BR, EDR and BLE functions.
PAGE 2
RF Exposure Considerations The module must be installed in the host equipment such that at least 20cm is maintained between the antenna and users’ body; and if RF exposure statement or module layout is changed, then the host product manufacturer required to take responsibility of the module through a change in FCC ID or new application. The FCC ID of the module cannot be used on the final product.
PAGE 3
Information on test modes and additional testing requirements • • • Operation Frequency: - WiFi: 2412 ~ 2462 MHz - Bluetooth: 2402 ~ 2480 MHz Number of Channels: - WiFi: 12 - Bluetooth: 40 Modulation: - WiFi: DSSS; OFDM - Bluetooth: GFSK; π/4 DQPSK; 8 DPSK Host manufacturer must perform test of radiated and conducted emission and spurious emission, etc.
PAGE 4
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • • This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
PAGE 5
IC Statement This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: • • This device may not cause interference; and This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
PAGE 6
This device is intended only for OEM integrators under the following conditions (For module device use): • • The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
PAGE 7
End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 12368A-KMET6000W”.