INSTRUCTION MANUAL Type Name : ICI3Q8-5293 Spec. No. AMO-NP-15167-01 No. of sheet Custody Distribution Notes : Sym. Revision Page ・ ・ ・ ・ ・ ・ ・ ・ ・ ・ Cha. No. Date By Reference Document Appr. Design H.Takahashi 2008.05.16 AMO-NP-07533-01 Type Name Det-che ・ ・ Appro. ・ ・ NIDEC SANKYO CORPORATION No.
No AMO – NP – 15167 – 01 1 /11 -----Table of Contents----Contents Page 1. Before Use 2 2. Important Notice 2 3. Attentions to this instruction manual and cautions 2 4. Scope 3 5. Equipment summary and functions 3 6. Unpacking 5 7. Setup 5 7.1 How to connect 5 1) Power cable (Connector) 5 2) USB Cable 6 3) Power cable (Plug) 6 Attention to the power supply 7.2 How to power on and off 6 7 1) How to turn on the power supply 7 2) How to shut off the power supply 7 7.
No AMO – NP – 15167 – 01 2 /11 1. Before use This operation manual is written for technical staff experienced in the general operation of magnetic and Non-contact IC card reader/encoders. It is intended to describe the operation of NIDEC Sankyo 's model ICI3Q8-5293. The terminal manufacturer shall be responsible to furnish an operation manual for end users. 2. Important Notice Misuse or mishandling may shorten product life or cause the product to malfunction or operate improperly.
No AMO – NP – 15167 – 01 3 /11 4. Scope This instruction manual is to describe proper handling procedures of the magnetic and Non-contact IC card reader/encoder, model number ICI3Q8-5293. 5. Equipment summary and functions Magnetic card reader/encoder, (hereafter referred to as MCRW), is a terminal with enclosure, and embedded power supply. It is configured to read and encode magnetic cards, working through an USB connection to the main computing system (hereafter referred to as HOST).
No AMO – NP – 15167 – 01 LED ・POWER lamp: Lights when power is on. ・READY lamp: Lights or blinks as defined by operation and card processing status ・ERROR lamp: Lights or blinks when an error occurs. LED Cover screw Card gate Front side Rear side Inlet AC Switch AC Switch Inlet USB Connector Fuse Backside Fig.
No AMO – NP – 15167 – 01 5 /11 6. Unpacking Included in the carton with the MCRW should be. Please inventory before proceeding. (1) MCRW 1 piece (2) Cables USB cable (SBE425501) 1 piece (to connect with Host computer) Power cable (SBE426401) 1 piece USB cable plug connector Power cable 7. Setup 7.1 How to connect 1) Power cable (Connector) Ensure that the AC switch is off. See section 7.2. Ensure that power LED is not lit.
No AMO – NP – 15167 – 01 6 /11 2) USB Cable Ensure that the AC switch is off. Turn the MCRW over and insert the USB cable securely into the USB connector. Connect the other end to the appropriate USB port on the HOST. USB Connector USB Cable . 3) Power cable (Plug) Set the MCRW in an upright position and plug in the power cable securely to AC120V outlet (grounded triple pin). Cautions 1. Do not exceed rated power supply input voltage 2. The power cable supplied with the MCRW is rated +125V 15A.
No AMO – NP – 15167 – 01 7 /11 7.2 How to turn on and shut off the power supply: 1) How to turn on the power supply: To power ON: press the " " on the AC switch. Power on When the power is ON, the power LED on the front panel is lit. Power lamp on 2) How to shut off the power supply: To power OFF: press the " " on the AC switch. Power off When the power is OFF, the power LED on the front panel is extinguished.
No AMO – NP – 15167 – 01 8 /11 Fuse holder Fuse Insertion direction Fuse holder Insertion opening Fuse holder turn ditch Fuse rated T2.5A/250V 7.4 How to remove a jammed card: Please refer to a trained technician for removal of a jammed card. When removing the jammed card, please follow the process below. 1) Switch off the AC and make sure that the power LED is extinguished. 2) Loosen the cover screw on the upper case rear (use a Phillips-head screwdriver.).
No AMO – NP – 15167 – 01 9 /11 (1) (2) AC Switch Upper case 5) Unhook the cover sheet from the top of the card reader and hold by the hook side. 6) Using tweezers, inserted from the top of the card reader, gently push the jammed card towards the gate until it can be easily removed by hand. 7) Place the upper case on the main body as shown by arrow (4) and slide forward, in the direction of arrow (5), then snap lock the upper case in place (6). 8) Fasten the cover screw (use a Phillips-head screwdriver).
No AMO – NP – 15167 – 01 10/11 8. Considerations for card handling Please use applicable cards. This equipment cannot handle any cards other than those specified. 1) Remove any foreign objects from the card. Wipe moisture or oils from cards with a dry cloth prior to using. Remove any, sticking tape, clips, or eraser residue to prevent card read errors. 2) Damaged cards may not be used on this equipment. Warped, bent, curled, punctured, or cracked cards may cause read/write errors or card jams.
No AMO – NP – 15167 – 01 10.Notes 1)FCC WARNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Properly shielded a grounded cables and connectors must be used for connection to host computer and/or peripherals in order to meet FCC emission limits. 2)NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.