User's Manual

1
Instructions and warnings for installation and use
Istruzioni ed avvertenze per l’installazione e l’uso
AIR 1RW/U
Sensor
___________________________________________________
GENERAL WARNINGS
Safety warnings
• During device installation, always strictly observe all
instructions in this manual. If in any doubt regarding
installation, do not proceed and contact the Nice Technical
Assistance for clarifications.
• CAUTION! – Important instructions: Keep these instructions
in a safe place to enable future product maintenance and
disposal operations.
• CAUTION! – All installation procedures, connections,
programming and maintenance of the product must be
performed exclusively by a qualified technician!
• Do not open the device protection housing as it contains non-
serviceable electrical circuits.
• Never apply modifications to any part of the device.
Operations other than as specified can only cause
malfunctions.
The manufacturer declines all liability for damage caused by
makeshift modifications to the product.
• Never place the device near sources of heat and never
expose to naked flames. This may damage it and cause
malfunctions.
• The product should not be used by children or people with
impaired physical, sensorial or mental capacities or who have
not received adequate training in the safe use of the product.
• Make sure that children do not play with the product.
• On the power line to the system, install a device for
disconnection from the power mains with a gap between
contacts that assures complete disconnection in the conditions
of overvoltage category III.
Other warnings
• Make sure that the surface of the sensor is as clean as
possible and is not obstructed: clean the surface using a soft
cloth avoiding the use of substances containing alcohol,
benzene, solvents or similar products.
• Handle the product with care, being sure not to crush, knock
or drop it in order to avoid damage.
• The product packaging material must be disposed of in full
observance of current local legislation governing waste
disposal.
1- PRODUCT DESCRIPTION AND INTENDED USE
This sensor is part of the “AIR” touchless sensor Nice range.
The sensors of these ranges are used to control automation
mechanisms for blinds: any external use is forbidden!
Functional specifications
• The “AIR” range consists of portable models. • Every model is
provided with a plate to mount the sensor on the wall. To
install this accessory please refer to fig. 1. • The fig. 2 reports
the only key (“RESET”) presents on the back side of the sensor.
2- TESTING THE SENSOR
Before memorizing the sensor in the receiver of the motor,
check its proper operation by pressing the “RESET” key and
observing whether the LEDS light up (fig. 3). If they do not,
refer to the section entitled “Replacing the Battery” in this
manual. Make one of the gestures listed in Table 1 and check a
movement of the motor.
3- SPECIFIC FUNCTIONS OF THE SENSOR
With this sensor, it is possible to send a command to the
automation with a hand gesture, selected from Table 1.
• CAUTION! • Keep the hand at a maximum distance of 5cm. •
Do not touch the surface of the sensor during the gesture.
Table 1
▲
ON / OPEN
▼
OFF / CLOSE
■
STOP
4- MEMORISING THE SENSOR ON THE AUTOMATION
RECEIVER
To memorize the sensor in a control unit (or in a receiver) it is
possible to choose one of the following procedures, compatibly
with the presence of this in the manual of the control unit or
the receiver:
A - Memorization in “Mode I”
B - Memorization in “Mode II”
C - Memorization of a new transmitter through another already
memorized
Note – key “■” (= Stop) on the transmitter specified in this
manual is equivalent to the sensor key “RESET” as shown in
fig.2.
The detailed instructions of each procedure are reported in the
instruction manual of the motor or the control unit with which
you want to make the transmitter work. These manuals are
also available in the website: www.niceforyou.com. Since in
the manuals the transmitter keys may be identified with
symbols or numbers please refer to Table 1 to know the
correspondence between these and the transmitter keys.
A - Memorization in “Mode I”
This mode automatically transfers, all together, the various
commands available in the motor, in the various gestures
available on the sensor, without giving the installer the
possibility of changing the combination among commands and
keys. In other words, during the execution of the procedure
that memorizes the sensor in this mode, the system
automatically combines the commands available in the motor
with each gestures on the sensor. At the end of the procedure
each gesture will be combined with a certain command,
according to the factory set layout.
B - Memorization in “Mode II”
This mode manually combines one of the commands available
in the motor with one of the sensor’s gestures, giving the
installer the possibility of choosing the command and the key
desired. In other words, during the execution of the procedure