Nexxt Solutions - Integrated Wireless IP Camera HTTP Port - In most cases, you can leave this value as 80; however, if your Internet Service Provider blocks this port, you may have to switch to another port number, such as 8005. Wireless LAN Settings Enter the wireless settings page of the Wireless Router to find out the SSID, Channel, Encryption and Authentication details. This product supports WEP and WAP security encryption methods.
Nexxt Solutions - Integrated Wireless IP Camera DDNS Service Settings The system supports protocols from some DDNS providers such as dyndns.org. Fill in the following fields once the DDNS service has been setup. User and Password: The User Name and Password used when applying for the domain name. DDNS Host: The domain name. DDNS or Proxy Server: If you access the DDNS host through a proxy, you should enter the Proxy IP here. DDNS or Proxy Port: The Proxy Port.
Nexxt Solutions - Integrated Wireless IP Camera Need Authentication - Check the box if the email needs authentication. If so, please enter the SMTP User Name & Password. Mail test: Set the Mail parameters and click ‘Submit’ before attempting to send a test email. There are 8 possible Mail Test errors: 1. Cannot connect to the server. 2. Network Error. Please try later. 3. Server Error. 4. Incorrect username or password. 5.
Nexxt Solutions - Integrated Wireless IP Camera sent. (For example: XPY 320`s address is http://119.123.207.96:9002). Make sure the port is mapped to the router correctly by UPnP or Virtual Map function. FTP Service Settings Note: When under Alarm Service Settings the option “Upload Image on Alarm” is checked, the FTP Service takes effect. FTP Server - The FTP server address. FTP port - The port usually is 21. FTP Mode - Supports standard (PORT) mode and passive (PASV) mode.
Nexxt Solutions - Integrated Wireless IP Camera 4. Incorrect username or password - Check the username and password. 5. Cannot access the folder - Ensure the folder exists and your account is authorized. 6. Error in PASV mode - Ensure the server supports PASV mode. 7. Error in PORT mode - PASV mode should be selected if the device is behind a NAT. 8. Cannot upload file - Ensure your account is authorized.
Nexxt Solutions - Integrated Wireless IP Camera setting with the highest motion detection sensitivity, while 10 represents the lowest sensitivity available you can preset. Send Mail on Alarm - Sends picture & mail information to the set email address after the alarm is triggered. Upload Image on Alarm - Enable this function to upload an image after the alarm is triggered.
Nexxt Solutions - Integrated Wireless IP Camera 7. Open the wireless router setup page and enter the SSID, Channel, Security Method (NONE, WEP), Authentication Type and Encryption. NOTE: This product supports WEP and WAP security encryption methods. 8. Click “Submit” to reboot the device. 9. Wait at least 30 seconds, then unplug the ethernet cable followed by the power supply. Power on the camera once again, making sure only the power supply is connected.
Nexxt Solutions - Integrated Wireless IP Camera Internet using the domain name. NOTE: Choose the option ‘Report ADSL IP by Mail’, for the ADSL IP address to be sent via email. Connect to the Internet using a router Follow the steps below to use a router to access the Internet by shared ADSL. If a router is set for dial-up Internet access, setting an ADSL dial-up account and password on the IP Camera is not required. 1. Use the Network cable to connect the IP Camera to the LAN. 2.
Nexxt Solutions - Integrated Wireless IP Camera the Camera directly through the Internet using the WAN IP. Two methods are available to obtain the WAN IP address. 1: Obtain the WAN IP from a Website You can discover this easily by turning on a computer using the same connection as the IP camera and entering this address: http://www. whatismyip.com.The page at this address will show you the current WAN IP. 2: Obtain the WAN IP address from the router 1.
Nexxt Solutions - Integrated Wireless IP Camera Note: Make sure Port mapping is successful. Port mapping can be configured in two ways: • Enter the setting page of the router which the IP camera connects with to enable the UPNP function. To do so, open the the IP camera “Upnp Settings” dialog box, and make sure the status for “Upnp is successful”. • If your router has the Virtual Map function, enter the router settings page, add the IP camera’s IP address and port number to the Virtual map list.
Nexxt Solutions - Integrated Wireless IP Camera 2. Enter DDNS Settings Page to enable the DDNS service, and click ‘Submit’ to reboot the camera. 3. Re-log in to the Camera web browser as Administrator and enter the ”DDNS Service Settings” page to check if the DDNS Status has been successfully changed to DynDNS. 4. Enter the ‘UPnP Settings’ page, the UPnP Status should be ‘Successful UPnP Session’. If not, you may enter the “Basic Network Settings” page to change the Http Port.
Nexxt Solutions - Integrated Wireless IP Camera (for example,http://ipcam.vicp.net, do not add www.) in the address bar of IE to access the IP Camera. If multiple IP Cameras are connected to the same router, enter DDNS dynamic domain with the port number (for example, http://ipcam.vicp.net:85) in the address bar of IE to access different IP cameras.
Nexxt Solutions - Integrated Wireless IP Camera Frequently Asked Questions Note: Please check network connections first to troubleshoot any potential problems. Check if any LED on the network, server, hub, exchange or network card is showing signs of malfunction. In case of abnormal operation, verify that all connections on the network have been done correctly.
Nexxt Solutions - Integrated Wireless IP Camera Network Configuration Double check to ensure that your HTTP server software is configured and running properly. If you are running any firewall software, make sure it is allowing inbound connections to port 80. Also, if you happen to be using a cable/DSL router, verify that you have set up the port forwarding feature properly (consult your router’s documentation for more information).
Nexxt Solutions - Integrated Wireless IP Camera Problems with network bandwidth The image frame rate depends on the following factors: 1. Network bandwidth. 2. PC performance, network environment and display preference setting (brightness, theme, etc). 3. The number of visitors (too many visitors will slow down the image frame rate). 4. Choice of switch or hub (use a switch for multiple IP cameras rather than a hub).
Nexxt Solutions - Integrated Wireless IP Camera Go to the IP camera’s ‘UPnP Settings’ to enable UPnP, making sure the ‘UPnP” configuration is successful. If your router has the Virtual Map function, enter the router setting page, and add the IP camera’s IP address and port number to the Virtual map list.
Nexxt Solutions - Integrated Wireless IP Camera 3. Wait for the download to complete. A dialog box will pop-up as shown as in the chart below. 4. Click the ‘Install Now’ button to start installation.
Nexxt Solutions - Integrated Wireless IP Camera 5. When installation is complete, click ‘Restart Firefox’ to initialize the browser. 6. Log in to your device and locate the monitoring page, right click on the web browser page and click the new menu item named ‘View page in IE-Tab’ to log in to the IP camera again.
Nexxt Solutions - Integrated Wireless IP Camera Default Parameters Default network parameters IP address: Automatically obtained Subnet mask: 255.255.255.
Nexxt Solutions - Integrated Wireless IP Camera SPECIFICATIONS Model AILP324U1 Specifications Camera Audio Video Pan/Tilt Network Alarm General Image sensor 1/4 color CMOS Lens 4 mm Infrared LED 10 pcs Pixels 300,000 Night vision range 15 m AWS/AGC/AES Auto Compression format MJPEG Minimum illumination 0.1 Lux Audio 2 way audio Input Built-in microphone Output Built-in speaker Image format PAL/NTSC Max.
