Instruction Manual

ManualsBrandsNexus Industrial Design ManualsElectronicsWeather Station (Remote Sensor)

INSTRUCTION MANUAL OF IW001-WWVB (V1.2) at March 26, 2009

Buttons

- (C/F) / WAVE

+ / TIME ZONE

SET / ALM SET

SNOOZE / LIGHT

MAX-MIN

OUT TEMP (RF REGISTER)

RESET

QUICK SETUP

Place your Atomic Weather Station close to a window and away from metal surfaces, electrical

appliances and strong magnetic field. Keep it at least 3 feet away from the AC outlet or AC/DC adaptor.

Step 1 Plug in the AC/DC adaptor to any AC household outlet. Then plug in the DC jack to the back of

your unit. Inset the stand to the bottom of your weather station.

Step 2 Slide open the battery cover at the back of your weather station, then insert 3 x AA alkaline

batteries (included) to the back of your weather station. Replace the battery cover.

Step 3 Press and hold +/ TIME ZONE to set your time zone, the time zone icons appear on top of the

time digits (“P” for Pacific Standard Time, “M” for Mountain Standard Time, “C” for Central Standard

Time, “E” for Eastern Standard Time) , then press and hold +/TIME ZONE for 2 seconds each time to

select your time zone.

Step 4 Keep your Atomic Weather Station and wireless sensor next to each other. Slide open the

battery cover at the back of your wireless outdoor sensor, then insert 2 x AA alkaline batteries to the

back of it. Replace the battery cover. Your weather station will receive data signal from the outdoor

sensor in few seconds. Then place your outdoor sensor in a dry and shaded area outdoor.

Step 5 Peel off the protective label on the front of your weather station clock. Your Atomic Weather

Station is ready to work for you.

Step 6 After your weather station receives the outdoor temperature and humidity, it will start to search

for the WWVB signal. This may take overnight In case your weather station does not catch the

WWVB signal during the day, set the clock manually.

Remarks:

1. Keep in mind that your outdoor sensor has a 100-feet open air transmission with no obstructions.

Actual transmission range will vary depending on what is in the path of the signal. Each obstruction

(roof, walls, floors, ceilings, thick trees, etc.) will effectively cut signal range in half.

2. During reception of the atomic time signal, all buttons does not function and your weather station

does not take temperature and humidity measurement. After first time installation, the temperature and

relative humidity readings will get stable and become more accurate in around 30 minutes.

BACK-UP BATTERIES

When the AC power is off, the batteries will back up the clock to keep the time, alarm time and calendar.

The always-on backlite of LCD is off when only the back-up batteries are being used.

WWVB RECEPTION

Summary of content (5 pages)

PAGE 1
INSTRUCTION MANUAL OF IW001-WWVB (V1.2) at March 26, 2009 Buttons - (C/F) / WAVE + / TIME ZONE SET / ALM SET SNOOZE / LIGHT MAX-MIN OUT TEMP (RF REGISTER) RESET QUICK SETUP Place your Atomic Weather Station close to a window and away from metal surfaces, electrical appliances and strong magnetic field. Keep it at least 3 feet away from the AC outlet or AC/DC adaptor. Step 1 Plug in the AC/DC adaptor to any AC household outlet. Then plug in the DC jack to the back of your unit.
PAGE 2
Your atomic weather station will automatically update itself to the exact time after receipt of the WWVB time code. This typically takes over night. The clock will automatically attempt to receive the WWVB signal every night at 1:00 am, 2:00am, 3:00 am, 4: 00 am and onwards. If it receives WWVB signal at 3:00 am it will stop receiving and start receiving at 1: 00 am next day. Manual reception of WWVB: press and hold the – / C/F / WAVE for 2 seconds. The WWVB icon will appear and flash.
PAGE 3
When time reaches your set alarm time, your weather station will give beep sound to wake you up. The “Bell” icon will flash. (insert BELL icon) 1) Press SNOOZE / LIGHT once to stop the alarm temporarily, the “Bell” icon keeps flashing. The alarm will beep again in 5 minutes. 2) To stop the alarm, press ALM On/Off once, the alarm beep will stop and the “Bell” icon become static, alarm will beep again same time next day.
PAGE 4
6. If the bars go down, it means the air pressure has dropped and the weather is expected to get worse from the present time “0h”. Remarks : moving your weather from one floor of a building to another floor will affect the accuracy of your weather station, which should operate at the same altitude all the time. If you move it to a new location, it will take 12-24 hours to get stable and accurate again. Our weather station provides next 12-24 hours weather forecast.
PAGE 5
CARE OF YOUR WEATHER SATATION CLOCK 1. 2. 3. 4. 5. Do not expose the unit to extreme temperature, water or direct sunlight Avoid contact with any corrosive materials Do not subject the unit to excessive force, dust or humidity Do not open the inner back case or tamper with any components of this unit Do not plug in any other AC/DC adaptor with incorrect specifications or voltage SPECIFICATIONS Temperature Range Indoor +32F to +113F (0C to +50C) (display shows HH.H / LL.