NEXOTRACK STARLIGHT QUICK START GUIDE Page |1
1.0 Introduction ........................................................................................................................................... 3 1.1 Technical Specs .................................................................................................................................. 4 1.2 Declaration ........................................................................................................................................ 5 2.0 Operation.........................
1.0 Introduction Before use, please read this manual carefully and keep it for later reference. • • • • • • • Do not disassemble the product and do not try to carry out repairs on this product. The product is not repairable. Do not attempt to replace the batteries and do not dispose of the device and batteries in fire or in a hot oven. Do not crush or crumple the device. Any use that does not conform to this manual will void the warranty and manufacturer's liability.
1.1 Technical Specs • • • • • • • • • • • • • • Dimensions (W x H x D): 122 x 42 x 43 mm (Excluding Bracket) Compatible Kegs Types: 50L, 30L, 20L, 9G & 1/6 Barrel Cask Weight: 122g RGB LED Water Ingress: IP69K Vibration Rating: IEC 60068-2-6:2007 Shock Rating: IEC 60068-2-27:2008 Operating Temperature: -20°C to +80°C Storage Temperature: -30°C to +80°C Maximum relative humidity: 100% 1 x Battery A-size, 3.6V, 3.
1.2 Declaration As of the date of manufacture, NexoTrack Starlight has been tested and found to comply with specifications for CE & FCC marking and standards per EMC and Radiocommunications Compliance Labelling. Federal Communications Commission (FCC) Compliance Statement This device complies with Part 15 of the FCC Rules. • Operation is subject to the following two conditions: (1) this device may not cause harmful interference.
2.0 Operation 2.1 QuickStart Guide 2.1.1 Activation NOTE: The new device can be installed only on the Keg which has correctly welded special bracket. If a bracket is not correctly installed the device will not function as intended. The device can be damaged when incorrectly installed. Please view bracket installation guide for details.
2.1.2 Bracket Installation The Starlight unit is mounted onto the Kegs using a permanently welded 1.7mm SS304 bracket. Below are requirements for bracket installation which must be followed to enable the correct function of the Starlight unit. If the bracket is not welded per below instructions, any warranty on the Starlight unit will be void. 1) Bottom of Starlight unit casing is lightly touching the Keg dome surface for sufficient heat transfer (tolerance is 0.0-0.5mm).
3) Starlight bracket should be positioned approximately middle point between the two handle openings of the Keg. 4) Bracket should be welded on at least 2 weld joints (total 4) using spot welding process on each side of the bracket or at least 1 plug weld joint (total 2) on each side of the bracket. The exact points used to carry out the welding are up to the welding professional service provider and the type of Keg being used.
2.1.3 Unit Assembly Following items will be required Attaching the device to the metal bracket Slide-in device onto the metal bracket. If the bracket is misaligned, wider or narrower than the device housing slots, insert one side first by 5mm and then push or pull the device to align the other side and push the device in.
Insert Retention Clips To ensure device attachment even during most extreme conditions, please insert the locking clips into the slots. Failing to install retention clips may lead to dislodgement of the unit in case of extreme shock/vibration conditions. Push clips firmly into the slots until you hear “click”. Make sure that the clip surface is aligned (flush) with the device surface.
2.1.4 Unit Removal The Starlight unit has been designed to be vandal resistant and is non-serviceable and is therefore not meant to be removed from the Keg once it is assembled. However, under special circumstances whereby removal of a unit is required the following steps can be followed to remove an assembled device from the bracket.
Step 2: Push removal tool fully into the first slot all the way into the retention clip slot as far as it can go.
Step 3: Gently pull unit back (halfway) Step 4: Push removal tool fully into the second slot NOTE: Orientation of removal tool P a g e | 13
Step 5: Gently pull the unit away from the bracket Step 6: Manually readjust bracket to the original position P a g e | 14
2.1.5 Sigfox Enrolment Sigfox backend account For a device to be able to communicate across the Sigfox network, it must be enrolled into your account which you must have with your respective Sigfox operator. Device credentials You will need a document with your device credentials: • • Device ID (Sigfox ID) Device PAC (Porting Authorization Code) Device label provides a barcode with the Device ID. Use the ID number to find correlating PAC number in the factory provided product list.
NOTE: All information shown in the screenshot above is for information only. You will need to enter actual numbers (ID, PAC) and select name and Type. The Starlight device ‘End product certificate’ is P_01B0_EB7A_01 Verify device enrolment From the ‘Device’ menu enter new device ID into the search.
Check the event and messaging status Click on device ID Click on P a g e | 17 :
Once the device has sent its first message, you should be able to see the above message. Congratulations, you have now successfully connected to the Sigfox network.
2.1.6 Nexotech Portal The status and location of Starlight devices can be tracked and monitored through a subscription-based portal. https://Starlight.panel.nexotechgroup.com Logon to the Starlight UI with allocated credentials: Enter device ID or device name (if known) into the search box. *NB: This can be a wildcard search.
Click on any unit to see the insights for that particular unit which includes complete log and device history. Now you can locate and monitor your Keg asset globally.
