Chapter 3: System Setup Installing the USB Cable Holder 2. Hook the cable to the holder as shown in the photo below. The USB cable holder is used to stabilize the USB cable so as to prevent it from getting loose when accidentally pulled or moved. 1. Attach the cable holder to the mounting hole by using the provided screw. Cable holder Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup Rackmount Brackets 2. Now mount the system on the wall by fastening screws through the bracket’s mounting holes. The rackmount brackets provide a convenient and economical way of mounting the system on the wall. 1. The mounting holes are located at the bottom of the system. Secure the brackets on each side of the system using the provided mounting screws.
Appendix A: I/O Address Function Appendix A: I/O Address Function Capacity of NEXCOM battery (8 bits) I/O port : 0EE1H GPIO LED / UMTS LED / Ignition Status I/O port : 0EE0H Bit Bit 0 Bit 1 Bit0 Function Description Description GPIO LED 0: OFF (default) 1: ON Ignition (read only) 0: OFF 1: ON Bit 3 Status of Vehicle Battery 0: Vehicle Battery is OK 1: Vehicle Battery is Low Voltage Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix A: I/O Address Function Status of NEXCOM battery (8 bits) I/O port : 0EE3H GPIO I/O port : 0EE4H Bit Function Description Bit Function Description Bit 0 Status for G sensor detection 0: Normal 1: Abnormal (X-axis or Y-axis degree is about 90 or -90) Bit 0-3 GPO 1-4 Bit 4-7 GPI 1-4 Bit 1 Power mode 0: 24V system 1: 12V system Bit 2 Fan mode 0: Auto 1: Always on Bit 3 Status of Smart battery 0: No discharging 1: Discharging Bit 4 Status of Fan R 0: Well 1: Failed Bit 5 Status of
Appendix A: I/O Address Function WDT I/O port : 0EE5H Onboard Module Disable/Enable I/O port : 0EE6H Bit Function Description Bit Function Description Bit 3 WDT Disable/Enable 0: Disable (default) 1: Enable Bit 0 3.
Appendix B: ICES200-L24 COM Express CPU Module Appendix B: ICES200-L24 COM Express CPU Module Overview Key Features ICES 200 is a Type 2 COM Express Module that features Intel® 945GME and ICH7M chipset; switch supports Intel® Core™ 2 Duo and Intel® Core™ 2 Duo LV processors with 533/667 MHz FSB. One DDR2 memory socket supports up to 2GB. The ICES 200 is integrated with Intel® Graphics Media Accelerator (GMA950) and expands via PCI Express Graphics x16 lanes to the carrier board.
Appendix B: ICES200-L24 COM Express CPU Module Specifications Display • Integrated with Intel® Graphics Media Accelerator (GMA950) or expand via PCI Express Graphics x16 lanes / Dual SDVO • CRT resolution up to 2048 x 1536 @ 60Hz, 1600 x 1200 @ 85Hz • One PCI Express x16 Lane down to the carrier board • Supports LFP (Local Flat Panel) LVDS interface with resolution up to 1366 x 768 • Supports Single channel for 18 bit / Dual Channel for 18 bit CPU Support • Supports Intel® Socket M, Core™ 2 Duo Family Pr
Appendix B: ICES200-L24 COM Express CPU Module Dimensions • COM Express Basic Module Type 2 • 95mm x 125mm Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix B: ICES200-L24 COM Express CPU Module Mechanical Dimensions Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix B: ICES200-L24 COM Express CPU Module PCI Routing Slot / Device Signal Slot / Device 0 Slot / Device 1 Slot / Device 2 Slot / Device 3 IDSEL AD20 AD21 AD22 AD23 INTA# IRQA IRQB IRQC IRQD INTB# IRQB IRQC IRQD IRQA INTC# IRQC IRQD IRQA IRQB INTD# IRQD IRQA IRQB IRQC COM Express Module Connector Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix B: ICES200-L24 COM Express CPU Module Connectors Row A GBE0_MDI0+ B13 SMB_CK A68 PCIE_TX0+ B68 PCIE_RX0+ GBE0_CTREF B14 SMB_DAT A69 PCIE_TX0- B69 PCIE_RX0- A15 SUS_S3# B15 SMB_ALERT# A70 GND B70 GND A16 SATA0_TX+ B16 SATA1_TX+ A71 LVDS_A0+ B71 LVDS_B0+ A17 SATA0_TX- B17 SATA1_TX- A72 LVDS_A0- B72 LVDS_B0- A18 SUS_S4# B18 SUS_STAT# A73 LVDS_A1+ B73 LVDS_B1+ A19 SATA0_RX+ B19 SATA1_RX+ A74 LVDS_A1+ B74 LVDS_B1- A20 SATA0_RX- B20 SATA1_RX- A7
Appendix B: ICES200-L24 COM Express CPU Module Row A Row B Row A Row B A40 USB4+ B40 USB5+ A95 RSVD B95 VGA_I2C_CK A41 GND B41 GND A96 GND B96 VGA_I2C_DAT A42 USB2- B42 USB3- A97 VCC_12V B97 NC A43 USB2+ B43 USB3+ A98 VCC_12V B98 NC A44 USB_2_3_OC# B44 USB_0_1_OC# A99 VCC_12V B99 NC A45 USB0- B45 USB1- A100 GND B100 GND A46 USB0+ B46 USB1+ A101 VCC_12V B101 VCC_12V A47 VCC_RTC B47 NC A102 VCC_12V B102 VCC_12V A48 EXCD0_PERST# B48 NC A1
Appendix B: ICES200-L24 COM Express CPU Module High Speed Board-to-Board Connector: COM Express Row C and Row D Connector size: 2 X 110 = 220 Pins Connector location: J1 Row C C68 PEG_RX5+ D68 PEG_TX5+ C14 IDE_IOR# D14 IDE_A1 C69 PEG_RX5- D69 PEG_TX5- C15 PCI_PME# D15 IDE_A2 C70 GND D70 GND C16 PCI_GNT2# D16 IDE_CS1# C71 PEG_RX6+ D71 PEG_TX6+ C17 PCI_REQ2# D17 IDE_CS3# C72 PEG_RX6- D72 PEG_TX6- C18 PCI_GNT1# D18 IDE_RESET# C73 SDVO_DATA D73 SDVO_CLK C19 PCI_RE
Appendix B: ICES200-L24 COM Express CPU Module Row C Row D Row C Row D C40 PCI_AD19 D40 PCI_AD22 C95 PEG_RX13- D95 PEG_TX13- C41 GND D41 GND C96 GND D96 GND C42 PCI_AD21 D42 PCI_AD24 C97 RSVD D97 PEG_ENABLE# C43 PCI_AD23 D43 PCI_AD26 C98 PEG_RX14+ D98 PEG_TX14+ C44 PCI_C/BE3# D44 PCI_AD28 C99 PEG_RX14- D99 PEG_TX14- C45 PCI_AD25 D45 PCI_AD30 C100 GND D100 GND C46 PCI_AD27 D46 PCI_IRQC# C101 PEG_RX15+ D101 PEG_TX15+ C47 PCI_AD29 D47 PCI_IRQD# C
Appendix B: ICES200-L24 COM Express CPU Module PCIE 1X4 or PCIE 4X1 SWITCH SW1 ON 1 2 4 3 SW_DIP-2 Pin Status Config 1 and 2 OFF PCIE 4X1 1 and 2 ON PCIE 1X4 Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board Appendix C: VTCB6110 Carrier Board Specifications I/O Interfaces - Front • 4 SMA-type mounting holes for WLAN, HSDPA and Bluetooth • 1 power button • 1 reset switch • 1 SIM card socket • 1 USB 2.0 • 4 LEDs for Standby, HDD, WLAN/HSDPA and GPO • 1 line-out • 1 mic-in Dimensions Expansion • 1 PCI-104 socket • 1 Bluetooth module (optional) • 2 Mini PCI Express socket - 1 PCIe interface for WLAN module - 1 PCIe + USB interface for 3.5G module Storage • One SATA 2.
Appendix C: VTCB6110 Carrier Board Jumpers and Connectors SW5 SW4 SW2 1 SW3 LED1 LED2 SW1 J2 1 USB1 J4 5 JP6 1 1 J3 Blue Tooth 10 1 JP5 1 J7 3 10 5 21 13 1 JP7 1 JP8 J14 1 29 JP4 2 J12 2 3 15 16 3 JP2 BZ1 17 18 3.
Appendix C: VTCB6110 Carrier Board Jumper Settings LVDS Power Input Voltage Select (JP9) Pin SW5: Input Voltage Selection SW5 / Input Voltage 12V (default) 24V 6V~36V SW5.1 OFF OFF ON SW5.2 OFF ON Ignore RS232 (default) RS485 SW6.1 OFF ON SW6.2 OFF ON SW6.3 OFF ON Status Function Description 1-2 Short Slave 2-3 (default) Short (default) Master Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved. 1-2 Short +5V IN 2-3 (default) Short (default) +3.
Appendix C: VTCB6110 Carrier Board Temp Sensor (JP8) GAL Download (JP5) Pin Function Description Pin Function Description 1 SENSOR+ 1 +V3.3S 2 GND 2 GND Auto Power Select (JP2) 3 TCK 4 TDO Pin Status Function Description 5 TDI 1-2 (default) Short (default) AUTO 6 TMS 2-3 Short BUTTON CONTROL MCU COM Port (JP3) PCI-104 VI/O Select Voltage (J13) Pin Function Description Pin Status Function Description 1 TX 1-4(*) Short* +3.
Appendix C: VTCB6110 Carrier Board Connectors Row A SMB_CK A68 PCIE_TX0+ B68 PCIE_RX0+ A14 GBE0_CTREF B14 SMB_DAT A69 PCIE_TX0- B69 PCIE_RX0- A15 SUS_S3# B15 SMB_ALERT# A70 GND B70 GND A16 SATA0_TX+ B16 NC A71 LVDS_A0+ B71 NC A17 SATA0_TX- B17 NC A72 LVDS_A0- B72 NC A18 SUS_S4# B18 SUS_STAT# A73 LVDS_A1+ B73 NC A19 SATA0_RX+ B19 NC A74 LVDS_A1+ B74 NC A20 SATA0_RX- B20 NC A75 LVDS_A2+ B75 NC A21 GND B21 GND A76 LVDS_A2+ B76 NC A22 NC
Appendix C: VTCB6110 Carrier Board Row A Row B Row A Row B A40 USB4+ B40 USB5+ A95 RSVD B95 NC A41 GND B41 GND A96 GND B96 NC A42 USB2- B42 USB3- A97 VCC_12V B97 NC A43 USB2+ B43 USB3+ A98 VCC_12V B98 NC A44 USB_2_3_OC# B44 USB_0_1_OC# A99 VCC_12V B99 NC A45 USB0- B45 USB1- A100 GND B100 GND A46 USB0+ B46 USB1+ A101 VCC_12V B101 VCC_12V A47 VCC_RTC B47 NC A102 VCC_12V B102 VCC_12V A48 NC B48 NC A103 VCC_12V B103 VCC_12V A49 NC B4
Appendix C: VTCB6110 Carrier Board High Speed Board-to-Board Connector: COM Express Row C and Row D Row C J1 COM Express B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B19 B20 B21 B22 B23 B24 B25 B26 B27 B28 B29 B30 B31 B32 B33 B34 B35 B36 B37 B38 B39 B40 B41 B42 B43 B44 B45 B46 B47 B48 B49 B50 B51 B52 B53 B54 B55 B56 B57 B58 B59 B60 B61 B62 B63 B64 B65 B66 B67 B68 B69 B70 B71 B72 B73 B74 B75 B76 B77 B78 B79 B80 B81 B82 B83 B84 B85 B86 B87 B88 B89 B90 B91 B92 B93 B94 B95 B96 B97 B98 B99
Appendix C: VTCB6110 Carrier Board Row C Row D Row C Row D C40 PCI_AD19 D40 PCI_AD22 C95 PEG_RX13- D95 PEG_TX13- C41 GND D41 GND C96 GND D96 GND C42 PCI_AD21 D42 PCI_AD24 C97 RSVD D97 PEG_ENABLE# C43 PCI_AD23 D43 PCI_AD26 C98 PEG_RX14+ D98 PEG_TX14+ C44 PCI_C/BE3# D44 PCI_AD28 C99 PEG_RX14- D99 PEG_TX14- C45 PCI_AD25 D45 PCI_AD30 C100 GND D100 GND C46 PCI_AD27 D46 PCI_IRQC# C101 PEG_RX15+ D101 PEG_TX15+ C47 PCI_AD29 D47 PCI_IRQD# C102 PEG_RX1
Appendix C: VTCB6110 Carrier Board CompactFlash Connector Pin Connector size: 2 x 25 = 50 pins Connector location: J12 23 Data 2 24 IOCS16# (NC) 25 CF_CD2# (Pull-down) 26 CF_CD1# (Pull-down) 27 Data 11 28 Data 12 29 Data 13 30 Data 14 31 Data 15 32 HDC CS300 33 CF_VS1# (NC) 34 IOR 35 IOW 36 CF_WE# (+5V) 37 Interrupt 15 38 +5V 39 CF_CSEL# (Master or Slave) 40 CF_VS2# (NC) 41 Reset # 42 IOCHRDY 43 DMA REQ / DACK (NC) 44 DMA ACK# /CF_REG# (+5V) 45 HDD Active Led
Appendix C: VTCB6110 Carrier Board GPIO Connector RS232 Connector: COM1, COM2 Connector size: DSUB-9 pin Connector location: COM1 Connector size: 2 x 10 = 20 Pins Pin Header, (2.0 mm Pitch) Connector location: COM1 (CN9), COM2 (CN7) 5 CN10 1 9 1 3 5 7 9 6 BOX-2.
Appendix C: VTCB6110 Carrier Board RS232/485 Connector: COM3 GAL Programmer PIN Header Connector size: 2 x 10 = 20 Pins Pin Header, (2.0 mm Pitch) Connector location: CN12 Connector size: 2.54mm-M-180 Connector location: JP5 CN10 1 3 5 7 9 2 4 6 8 10 1 2 3 4 5 6 JP5 BOX-2.0mm-M-180 PIN-2.
Appendix C: VTCB6110 Carrier Board MCU Programmer Pin Header VGA Connector Connector size: 2.54mm-M-180 Connector location: JP6 Connector size: DSUB-15 Connector location: CON1 1 2 3 4 5 JP6 PIN-2.54mm-M-180 Connector Pin Definition Connector Pin Definition Pin Definition Pin Definition Pin Definition Pin Definition 1 1 +3.
Appendix C: VTCB6110 Carrier Board LVDS Connector + USB0 Pin Connector size: 2 x 15 (2.0mm) Connector location: CN3 17 LVDS_5(OUT2) 18 Panel_backlight(+12V) 19 LVDS_4(OUT2#) 20 Panel_backlight(+12V) 21 LVDS_GND 22 Power on push buttom 23 USB_0# 24 USB_GND 25 USB_0 26 USB_VCC (+5V) 27 USB_GND 28 USB_GND 29 Panel_backlight(+12V) 30 GND CN3 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 Definition Pin Definition BOX-2.
Appendix C: VTCB6110 Carrier Board LAN Connector USB Connector Connector size: RJ-45 Connector location: LAN1 Connector location: USB1 Connector Pin Definition Connector Pin Definition Pin Definition Pin Pin Definition 1 TX+ 2 TX- 3 RX+ 4 N/C1 5 N/C2 6 RX- 7 N/C3 8 N/C4 9 LAN Speed LED 10 +3.3V 11 LAN Link LED 12 +3.3V Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board USB Connector LVDS Power Connector Connector location: USB2 Connector location: J5 1 Connector Pin Definition Connector Pin Definition Pin Pin Definition 1 Definition VCC 2 DATA1- 3 DATA1+ 4 GND 5 VCC 6 DATA- 7 DATA+ 8 GND Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board External 12V & 5V Power and SMBUS Connector Mic-in Connector location: CN2 Connector location: CN11 and CN15 6 4 3 1 Connector Pin Definition Connector Pin Definition Pin Definition Pin 1 5V 2 12V 3 SMBCLK 4 GND 5 GND 6 SMBDATA Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board Line-out PCI-104 VI/O Voltage Setting Connector location: CN8 and CN14 Connector location: J13 Connector Pin Definition Pin Definition Pin 1 LINE_OUT_L 2 SURR_JD 3 NC 4 LINE_OUT_R 5 GND 6 Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved. Definition 2 4 6 1 3 5 Connector Pin Definition GND 88 Pin No. Status 1-3, 2-4 (default) Short Function Description +3.
Appendix C: VTCB6110 Carrier Board PCI-104 Connector Power Button Connector location: CN16 Connector location: SW1 Connector Pin Definition Reset Button Connector location: SW2 Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board MCU COM Port ACC_ON LED Connector location: JP3 Connector location: JP7 Connector Pin Definition 1 Pin Function Description 1 TX 2 RX Pin Function Description 3 GND 1 +3.3V LED 2 GND Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board Temp Sensor DC Power Input Connector Connector location: JP8 Connector location: CN1 1 Connector Pin Definition Pin Function Description 1 SENSOR+ 2 GND Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board Power On and IDE Active LED GPIO and UMTS LEDs Connector location: LED1 Connector location: LED2 T1 T2 B1 B2 LED I/O Port Address and Data Connector Pin Definition LED Function Description LED Function Description T1 POWER LED T2 I/O PORT Address: 0EE0; Bit0: 1 (Light), 0 (Dark) B1 HD LED B2 UMTS STATUS Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board Serial ATA Serial ATA Power Input Connector location: CN6 Connector location: J10 7 4 1 Connector Pin Definition 1 Connector Pin Definition Pin Definition Pin Definition Pin Definition 1 GND 2 SATA_TXP0 - 1 +V12S 2 GND 3 SATA_TXN0 4 GND 3 GND 4 +V5S 5 SATA_RXN0 6 SATA_RXP0 7 GND Pin Definition Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board Mini-PCIe Socket (for 3.5G module) PCIe Interface Mini-PCIe Socket (for WLAN module) USB + PCIe Interface Connector location: CN10 Connector location: CN13 2 52 2 52 1 51 1 51 Connector Pin Definition Pin Definition Pin Connector Pin Definition Definition Pin Definition Pin Definition Definition Pin Definition Pin Definition 1 MIC + 2 +V3.3S 27 GND 28 NC 1 WAKE# 2 +V3.3S 27 GND 28 +V1.
Appendix C: VTCB6110 Carrier Board Bluetooth Connector Connector location: CN4 Connector location: J7 MH2 MH1 SIM Card Connector 1 2 3 4 5 6 7 8 9 10 J7 JST-1mm-M-90 Pin Connector Pin Definition Pin Definition Pin Definition Pin Definition 1 GND 2 USB_6P_L Definition 3 USB_6N_L 4 NC NC 6 BT_AUDIO_EN_R C1 POWER VOLTAGE C2 RESET SIGNAL 5 C3 CLOCK SIGNAL C5 GND 7 NC 8 BT_3.
Appendix D: BIOS Setup Appendix D: Vehicle Power Management Setup External Power Output Setting External +12V and +5V Turn Off Simultaneously External +12V and +5V Turn On Simultaneously Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix D: BIOS Setup External +5V Turn On Only External +12V Turn On Only Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix D: BIOS Setup Startup and Shutdown Voltage Setting 2. If the input voltage setting is 12V: set the startup voltage to 12V and the shutdown voltage to 11V. 1. If the input voltage setting is 12V: set the startup voltage to 11.5V and the shutdown voltage to 10.5V. If the input voltage setting is 24V: set the startup voltage to 24V and the shutdown voltage to 22V. If the input voltage setting is 24V: set the startup voltage to 23V and the shutdown voltage to 21V.
Appendix D: BIOS Setup 3. If the input voltage setting is 12V: set the startup voltage to 12.5V and the shutdown voltage to 11V. 4. If the input voltage setting is 12V: set the startup voltage to 12.5V and the shutdown voltage to 11.5V. If the input voltage setting is 24V: set the startup voltage to 25V and the shutdown voltage to 22V. If input voltage setting is 24V: set the startup voltage to 25V and the shutdown voltage to 23V.
Appendix D: BIOS Setup Power-on Delay Setting Enable Power-on Delay Delay time can be set at 10sec/30sec/1min./5min./10min./15min./30min./ 1hour. Disable Power-on Delay Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix D: BIOS Setup Power-off Delay Setting Disable Power-off Delay Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix D: BIOS Setup Enable Power-off Delay Delay time can be set at 20sec/1min./5min./10min./30min./1hour/6hour/ 18hour. Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
For mobile devices without co-location condition ( the transmitting antenna is installed or located more than 20cm away from the body of user and near by person ) FCC RF Radiation Exposure Statement: 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
