NEXCOM International Co., Ltd. Mobile Computing Solutions Vehicle Telematics Computer VTC 6110ATT4 User Manual NEXCOM International Co., Ltd. Published January 2010 www.nexcom.
Contents CONTENTS Preface Copyright ............................................................................................. Disclaimer ............................................................................................. Acknowledgements .............................................................................. Regulatory Compliance Statements ....................................................... Declaration of Conformity..................................................................
Contents RS232/485 Connector: COM3 ........................................................... GAL Programmer PIN Header............................................................. MCU Programmer Pin Header............................................................ VGA Connector................................................................................. LVDS Connector + USB0 .................................................................... LAN Connector............................................
Preface PREFACE Copyright Regulatory Compliance Statements This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written consent from NEXCOM International Co., Ltd. This section provides the FCC compliance statement for Class B devices and describes how to keep the system CE compliant.
Preface e13 Mark How to recognize NEXCOM RoHS Products? The “e” mark is the proof of compliance with directives (laws) required by the European Union. The Council of European communities in Brussels issues these directives and all members must accept approved products. For existing products where there are non-RoHS and RoHS versions, the suffix “(LF)” will be added to the compliant product name. All new product models launched after January 2006 will be RoHS compliant.
Preface Warranty and RMA NEXCOM Warranty Period Any products returned by NEXCOM to other locations besides the customers’ site will bear an extra charge and will be billed to the customer. NEXCOM manufactures products that are new or equivalent to new in accordance with industry standard. NEXCOM warrants that products will be free from defect in material and workmanship for 2 years, beginning on the date of invoice by NEXCOM.
Preface Warnings Installation Recommendations Read and adhere to all warnings, cautions, and notices in this guide and the documentation supplied with the chassis, power supply, and accessory modules. If the instructions for the chassis and power supply are inconsistent with these instructions or the instructions for accessory modules, contact the supplier to find out how you can ensure that your computer meets safety and regulatory requirements. Ensure you have a stable, clean working environment.
Preface Safety Precautions 12. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage. 1. Read these safety instructions carefully. 2. Keep this User Manual for later reference. 13. Never pour any liquid into an opening. This may cause fire or electrical shock. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 14. Never open the equipment.
Preface Technical Support and Assistance Conventions Used in this Manual Warning: Information about certain situations, which if not observed, can cause personal injury. This will prevent injury to yourself when performing a task. 1. For the most updated information of NEXCOM products, visit NEXCOM’s website at www.nexcom.com. 2.
Preface Global Service Contact Information Headquarters Taiwan Germany Leopoldstrase Business Centre, Leopoldstrase 244 80807 Munich, Germany Tel: +49-89-208039-278 Fax: +49-89-208039-279 http://www.nexcom.eu 18F, No. 716, Chung-Cheng Rd. Chung-Ho City, Taipei County 235, Taiwan, R.O.C. Tel: +886-2-8228-0606 Fax: +886-2-8228-0501 http://www.nexcom.com.tw Italy USA Via Gaudenzio Ferrari 29, 21047 Saronno (VA) Italia Tel: +39 02 9628 0333 Fax: +39 02 9619 8846 http://www.nexcom.
Preface China-Beijing Japan Room 301, Block E, Power Creative Building, No. 1 Shangdi East Rd. Haidian Dist., Beijing, 100085, China Tel: +86-10-5885-6655 Fax: +86-10-5885-1066 http://www.nexcom.cn 10F, Nakagin-Shiroyama Building, 8-16-13. Ginza Chuou-ku, Tokyo 104-0061, Japan Tel: +81-3-3524-4250 Fax: +81-3-3524-4252 http://www.nexcom-jp.com China-Shanghai Office Room 1505, Greenland He Chuang Building, No. 450 Caoyang Rd. Shanghai, 200063, China Tel: +86-21-6150-8008 Fax: +86-21-3251-6358 http://www.
Preface PACKAGE CONTENTS Before continuing, verify that the VTC 6110 package that you received is complete. Your VTC 6110 package should have all the items listed in the following table. Item P/N Name Specification Qty 1 4NCPM00302X00 POWER CON 3P PHOENIX CONTACT 2 5060100017X00 DAMPER 6mm/OUTSIDE DIA .12mm H: 9mm TPS(BLACK) 4 3 50311F0119X00 I HEAD BOLTS SCREW LONG I3x12.5 AXISx 8.
Preface Item P/N Name Specification Qty 11 5043330247X00 HDD BRACKET 129.5x97x 1mm 1 12 5043330246X00 HDD BRACKET FOR CUSHION LEFT 123.3x44.5x 14.7mm 1 13 5043330245X00 HDD BRACKET FOR CUSHION RIGHT 128.5x17x 1mm 1 14 50344C0067X00 COPPER POST LONG WITH MALE/FEMALE (FEMALE)16mmx(MALE)5mmxM3 4 15 5060100012X00 HIGH-END DAMPER INSIDE 11.1mm H: 10.
Preface ORDERING INFORMATION The following provides ordering information for VTC 6110. · VTC 6110 (P/N: 10V00611000X0) - with Intel Core™ Duo L2400, 1GB DDR2 memory, GPS module and GPS antenna Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 1: Product Introduction CHAPTER 1: PRODUCT INTRODUCTION Overview VTC6110 fulfills vehicle industry requirements. The design itself is in compliance with vehicle industrial standard such as eMark. More features required for in-vehicle operations, such as power ignition delay control, low-power protection and SMBus connection, etc., are continued from NEXCOM’s other in-vehicle computer products. The GPS function navigates drivers to ultimate the fleet management. Optional 802.11b/g/n, 3.
Chapter 1: Product Introduction Key Features I/O Interfaces - Front · · · · · · · · · · · · · · · · · · · · Built-in Intel® Core™ Duo LV processor Fanless design with ruggedized aluminum chassis 2 Mini PCI Express and 1 PCI-104 expansions Wide range DC input from 6V to 36V Power ignition on/off delay controlled by software Low battery power protection setting by software External smart battery back-up support S3 & S4 suspend mode support Availability of GPS, GPRS/UMTS/HSDPA Multiple display connections
Chapter 1: Product Introduction · 6V (15A) to 36V (5A) thru DC 3-pin power input connector (ignition, power input and ground) · 1 x DB9 Female for digital I/O with 4-input and 4-output · +5 VDC (1A) and +12VDC (1A) power output and SMBus (w/o VTK 33M-01 connection) +5 VDC (0.5A) and +12VDC (0.
Chapter 1: Product Introduction Power Management · If the ignition is turned off again and the power-on delay ended (in BIOS process), VTC 6110 will shut down immediately. · If VTC 6110 is off, only below 10mA is used. · Power-on delay time is selectable by BIOS to disable and enable in 10sec / 30sec / 1min / 5min / 10 min / 15min / 30min / 1hr. · Power-off delay time is selectable by BIOS to disable and enable in 20sec / 1min / 5min / 10min / 30min / 1hr / 6hr / 18hr.
Chapter 1: Product Introduction COM Express CPU Module and Carrier Board The VTC 6110 system uses the ICES200-L24 COM Express CPU module and the VTCB6110 carrier board. ICES200-L24 COM Express CPU Module ICES200-L24 is a COM Express CPU module that uses the Intel® 945GME chipset and supports Intel® Core™ Duo L2400. The module also supports one unbuffered non-ECC 533/667 DDR2 SODIMM with maximum memory size up to 2GB.
Chapter 1: Product Introduction Physical Features 2. Mode B. When the ignition is from “low” to “high”, you can turn on VTC 6110 only by pressing the power button. When the ignition is “high”, you can press the power button to turn on/off VTC 6110. Front Panel GPRS/UMTS/HSDPA module antenna mounting holes If the ignition is from “high” to “low”, VTC 6110 will turn off automatically. When the ignition is “low”, pressing the power button will not turn on VTC 6110.
Chapter 1: Product Introduction LEDs GPIO COMM I/O PORT Address : #0EE0H Bit 0 : WLAN/HSDPA Status SIM Card Socket VTC 6110 can be internally integrated with a 3.5G Mini Card module. The SIM card bracket is on the carrier board. When using the GPRS/UMTS/HSDPA function, insert the SIM card into the SIM card socket. Make sure to turn off VTC 6110 before inserting the SIM card. USB Port The USB port complies with USB 2.0 specifications.
Chapter 1: Product Introduction Power Input Rear Panel GPS COM2 COM3 DC Power Input Connector Connector location LVDS COM1 3 2 1 Connector pin definition (CN1) LAN GPIO DVI-D USB VGA Pin No. DC IN 6V-36V 5V/12V/SMBUS MIC-IN Function Description 1 GND 2 VIN(6V~36V) 3 IGNITION ** Use power cable (+) with fuse for system protection LINE-OUT Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 1: Product Introduction RS232/485 Connector COM3 RS232 Connector COM1 and COM2 The 9 pin D-Sub COM 3 port can be configured as RS232 or RS485 using the SW6 dip switch.
Chapter 1: Product Introduction LVDS External SMBus, 12V and 5V Power Output Connector size: DB-26 PIN Connector location Connector location 6 4 3 1 Connector pin definition PIn Connector pin definition Pin Definition Pin Definition 1 Panel_ EN 2 Panel_control 3 VDD 4 VDD 5 LCDD09(OUT3) 6 LCDD01(OUT0) 7 LCDD08(OUT3#) 8 LCDD00(OUT0#) 9 LCDD_GND 10 LCDD_GND 11 LCDD07(CLK) 12 LCDD03(OUT1) 13 LCDD06(CLK#) 14 LCDD02(OUT1#) 15 LVDS_GND 16 LCDD_GND 17 LCDD05(OUT2) 18
Chapter 1: Product Introduction VGA Port The DB15 VGA port supports resolutions up to 1600x1200 @ 85 Hz, 2048x1536 @ 60Hz. USB Port x 2 The two USB ports are compliant with USB 2.0 specifications. LAN Port The LAN port is an RJ45 interface with integrated LEDs and supports 10/100/1000Mbps Ethernet data transfer rates. Audio Jacks (MIC-IN and LINE-OUT) · MIC-IN jack receives monophonic input from an external microphone. · LINE-OUT jack is the stereo output for connecting external speakers.
Chapter 1: Product Introduction Mechanical Dimensions 176.0 50.0 260.0 Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 2: Jumpers and Connectors CHAPTER 2: JUMPERS AND CONNECTORS This chapter describes how to set the jumpers on the motherboard. Note that the following procedures are generic for all VTC 6110 series. tronic components. Humid environment tend to have less static electricity than dry environments. A grounding strap is warranted whenever danger of static electricity exists. Before You Begin Precautions · Ensure you have a stable, clean working environment.
Chapter 2: Jumpers and Connectors Jumper A jumper is the simplest kind of electric switch. It consists of two metal pins and a cap. When setting the jumpers, ensure that the jumper caps are placed on the correct pins. When the jumper cap is placed on both pins, the jumper is short. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is open. Refer to the illustrations below for examples of what the 2-pin and 3-pin jumpers look like when they are short (on) and open (off).
Chapter 2: Jumpers and Connectors Locations of the Jumpers and Connectors VTCB6110 The figure on the right is the VTCB6110 carrier board which is the board used in the VTC6110 system. It shows the locations of the jumpers and connectors. SW5SW4 SW2 SW7 CN15 J11 CN14 LED2 J13 SW3 J9 USB1 LED1 SW1 J2 J4 CN17 J1 CN4 JP6 J12 J3 Blue Tooth JP5 J7 JP4 JP8 10 J14 JP7 JP3 JP2 BZ1 3.
Chapter 2: Jumpers and Connectors Jumper Settings LVDS Power Input Voltage Select (JP9) Pin SW5: Input Voltage Selection SW5 / Input 12V (default) 24V 6V~36V SW5.1 OFF OFF ON SW5.2 OFF ON Ignore Status Function Description 1-2 Short +5V IN 2-3 (default) Short (default) +3.
Chapter 2: Jumpers and Connectors Temp Sensor (JP8) GAL Download (JP5) Pin Function Description Pin Function Description 1 SENSOR+ 1 +V3.3S 2 GND 2 GND Auto Power Select (JP2) 3 TCK 4 TDO Pin Status Function Description 5 TDI 1-2 (default) Short (default) AUTO 6 TMS 2-3 Short BUTTON CONTROL Pin Function Description Pin Status Function Description 1 TX 1-4(*) Short* +3.
Chapter 2: Jumpers and Connectors Connectors Row A SMB_CK A68 PCIE_TX0+ B68 PCIE_RX0+ A14 GBE0_CTREF B14 SMB_DAT A69 PCIE_TX0- B69 PCIE_RX0- A15 SUS_S3# B15 SMB_ALERT# A70 GND B70 GND A16 SATA0_TX+ B16 NC A71 LVDS_A0+ B71 NC A17 SATA0_TX- B17 NC A72 LVDS_A0- B72 NC A18 SUS_S4# B18 SUS_STAT# A73 LVDS_A1+ B73 NC A19 SATA0_RX+ B19 NC A74 LVDS_A1+ B74 NC A20 SATA0_RX- B20 NC A75 LVDS_A2+ B75 NC A21 GND B21 GND A76 LVDS_A2+ B76 NC A22 NC B
Chapter 2: Jumpers and Connectors Row A Row B Row A Row B A40 USB4+ B40 USB5+ A95 RSVD B95 NC A41 GND B41 GND A96 GND B96 NC A42 USB2- B42 USB3- A97 VCC_12V B97 NC A43 USB2+ B43 USB3+ A98 VCC_12V B98 NC A44 USB_2_3_OC# B44 USB_0_1_OC# A99 VCC_12V B99 NC A45 USB0- B45 USB1- A100 GND B100 GND A46 USB0+ B46 USB1+ A101 VCC_12V B101 VCC_12V A47 VCC_RTC B47 NC A102 VCC_12V B102 VCC_12V A48 NC B48 NC A103 VCC_12V B103 VCC_12V A49 NC B49
Chapter 2: Jumpers and Connectors High Speed Board-to-Board Connector: COM Express Row C and Row D Connector size: 2 X 110 = 220 Pins Connector location: J3 Row C Row D Row C Row D C13 IDE_IORDY D13 IDE_A0 C68 NC D68 NC C14 IDE_IOR# D14 IDE_A1 C69 NC D69 NC C15 NC D15 IDE_A2 C70 GND D70 GND C16 NC D16 IDE_CS1# C71 NC D71 NC C17 NC D17 IDE_CS3# C72 NC D72 NC C18 NC D18 IDE_RESET# C73 NC D73 SDVO_CLK C19 NC D19 NC C74 NC D74 NC C20 PCI_GNT0# D20
Chapter 2: Jumpers and Connectors Row C Row D Row C Row D C40 PCI_AD19 D40 PCI_AD22 C95 PEG_RX13- D95 PEG_TX13- C41 GND D41 GND C96 GND D96 GND C42 PCI_AD21 D42 PCI_AD24 C97 RSVD D97 PEG_ENABLE# C43 PCI_AD23 D43 PCI_AD26 C98 PEG_RX14+ D98 PEG_TX14+ C44 PCI_C/BE3# D44 PCI_AD28 C99 PEG_RX14- D99 PEG_TX14- C45 PCI_AD25 D45 PCI_AD30 C100 GND D100 GND C46 PCI_AD27 D46 PCI_IRQC# C101 PEG_RX15+ D101 PEG_TX15+ C47 PCI_AD29 D47 PCI_IRQD# C102 PEG_RX15
Chapter 2: Jumpers and Connectors CompactFlash Connector Pin Connector size: 2 x 25 = 50 pins Connector location: J12 50 49 26 1 Connector Pin Definition Pin Description Pin Description 1 Gnd 2 Data 3 3 Data 4 4 Data 5 5 Data 6 6 Data 7 7 HDC CS100 8 Gnd 9 Gnd 10 Gnd 11 Gnd 12 Gnd 13 +5V 14 Gnd 15 Gnd 16 Gnd 17 Gnd 18 Disk Address 2 19 Disk Address 1 20 Disk Address 0 21 Data 0 22 Data 1 Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 2: Jumpers and Connectors GPIO Connector RS232 Connector: COM1, COM2 Connector size: DSUB-9 pin Connector location: COM1 Connector size: 2 x 10 = 20 Pins Pin Header, (2.0 mm Pitch) Connector location: COM1 (CN9), COM2 (CN7) 5 CN10 1 9 1 3 5 7 9 6 BOX-2.
Chapter 2: Jumpers and Connectors RS232/485 Connector: COM3 GAL Programmer PIN Header Connector size: 2 x 10 = 20 Pins Pin Header, (2.0 mm Pitch) Connector location: CN12 Connector size: 2.54mm-M-180 Connector location: JP5 CN10 1 3 5 7 9 1 JP5 2 3 4 5 6 42 6 8 10 BOX-2.0mm-M-180 PIN-2.
Chapter 2: Jumpers and Connectors MCU Programmer Pin Header VGA Connector Connector size: 2.54mm-M-180 Connector location: JP6 Connector size: DSUB-15 Connector location: CON1 1 JP6 2 3 4 5 PIN-2.54mm-M-180 Connector Pin Definition Connector Pin Definition Pin Definition Pin Definition Pin Definition Pin Definition 1 1 +3.
Chapter 2: Jumpers and Connectors LVDS Connector + USB0 Pin Pin Definition 17 LVDS_5(OUT2) 18 Panel_backlight(+12V) 19 LVDS_4(OUT2#) 20 Panel_backlight(+12V) 21 LVDS_GND 22 Power on push buttom 42 6 8 23 USB_0# 24 Contact_DET# 25 USB_0 26 USB_VCC (+5V) 10 12 14 16 18 20 22 24 26 28 30 27 USB_GND 28 USB_GND 29 Panel_backlight(+12V) 30 GND Connector size: 2 x 15 (2.0mm) Connector location: CN3 CN3 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 Definition BOX-2.
Chapter 2: Jumpers and Connectors LAN Connector USB Connector Connector size: RJ-45 Connector location: LAN1 Connector location: USB1 Connector Pin Definition Connector Pin Definition Pin Definition Pin Pin Definition 1 TX+ 2 TX- 3 RX+ 4 N/C1 5 N/C2 6 RX- 7 N/C3 8 N/C4 9 LAN Speed LED 10 +3.3V LAN Link LED 12 +3.3V 11 Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 2: Jumpers and Connectors USB Connector LVDS Power Connector Connector location: USB2 Connector location: J5 1 Connector Pin Definition Connector Pin Definition Pin Pin Definition 1 Definition VCC 2 DATA1- 3 DATA1+ 4 GND 5 VCC 6 DATA- 7 DATA+ 8 GND Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 2: Jumpers and Connectors External 12V & 5V Power and SMBUS Connector Mic-in Connector location: CN2 Connector location: CN11 and CN15 6 4 3 1 Connector Pin Definition Connector Pin Definition Pin Pin Definition Pin Definition 1 5V 2 12V 3 SMBCLK 4 GND 5 GND 6 SMBDATA Definition Pin Definition 1 NC 2 MIC_JD 3 NC 4 MIC_OUT 5 GND 6 GND FOR AT&T NO This Function Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 2: Jumpers and Connectors Line-out PCI-104 VI/O Voltage Setting Connector location: CN8 and CN14 Connector location: J13 Connector Pin Definition Pin Definition Pin 1 LINE_OUT_L 2 SURR_JD 3 NC 4 LINE_OUT_R 5 GND 6 Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved. Definition 2 4 6 1 3 5 Connector Pin Definition GND 30 Pin No. Status Function Description 1-3, 2-4 (default) Short +3.
Chapter 2: Jumpers and Connectors PCI-104 Connector Power Button Connector location: CN16 Connector location: SW1 Connector Pin Definition Reset Button Connector location: SW2 Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 2: Jumpers and Connectors MCU COM Port ACC_ON LED Connector location: JP3 Connector location: JP7 Connector Pin Definition 1 Pin Function Description 1 TX 2 RX Pin Function Description 3 GND 1 +3.3V LED 2 GND Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 2: Jumpers and Connectors Temp Sensor DC Power Input Connector Connector location: JP8 Connector location: CN1 1 Connector Pin Definition Pin Connector Pin Definition Function Description 1 SENSOR+ 2 GND Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 2: Jumpers and Connectors Power On and IDE Active LED GPIO and UMTS LEDs Connector location: LED1 Connector location: LED2 T1 T2 B1 B2 LED I/O Port Address and Data Connector Pin Definition LED Function Description LED T1 POWER LED T2 I/O PORT Address: 0EE0; Bit0: 1 (Light), 0 (Dark) B1 HD LED B2 UMTS STATUS Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 2: Jumpers and Connectors Serial ATA Serial ATA Power Input Connector location: CN6 Connector location: J10 7 4 1 Connector Pin Definition Pin 1 Definition GND 1 Connector Pin Definition Pin Definition Pin Definition Pin 2 SATA_TXP0 - 1 +V12S 2 GND 3 GND 4 +V5S 3 SATA_TXN0 4 GND 5 SATA_RXN0 6 SATA_RXP0 7 GND Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 2: Jumpers and Connectors Mini-PCIe Socket (for 3.5G module) PCIe Interface Mini-PCIe Socket (for WLAN module) USB + PCIe Interface Connector location: CN10 Connector location: CN13 2 52 2 52 1 51 1 51 Connector Pin Definition Pin Definition Pin Definition Pin Definition Definition Pin Definition Pin Definition 1 MIC + 2 +V3.3S 27 GND 28 NC 1 WAKE# 2 +V3.3S 27 GND 28 +V1.
Chapter 2: Jumpers and Connectors Bluetooth Connector Connector location: CN4 Connector location: J7 MH2 MH1 SIM Card Connector 1 2 3 4 5 6 7 8 10 9 J7 Pin Connector Pin Definition Pin Definition Pin Definition Pin GND 2 USB_6P_L Definition 3 USB_6N_L 4 NC NC 6 BT_AUDIO_EN_R BT_3.3V C1 POWER VOLTAGE C2 RESET SIGNAL 5 C3 CLOCK SIGNAL C5 GND 7 NC 8 I/O 9 NC 10 C6 VPP:PROGRAM VOLTAGE SW Contact present switch C7 Copyright © 2009 NEXCOM International Co., Ltd.
Chapter 3: System Setup CHAPTER 3: SYSTEM SETUP Removing the Chassis Cover Prior to removing the chassis cover, make sure the unit’s power is off and disconnected from the power sources to prevent electric shock or system damage. 1. The screws on the cover are used to secure the cover to the chassis. Remove these screws and put them in a safe place for later use. Bottom View 2. Lift the cover upward then remove it from the chassis. Front View Rear View Copyright © 2009 NEXCOM International Co., Ltd.
Chapter 3: System Setup Installing a GPRS/UMTS/HSDPA Module 2. Insert the module into the Mini PCI Express slot at a 45 degrees angle until the gold-plated connector on the edge of the module completely disappears inside the slot. 1. The Mini PCI Express slot shown below is used to install a 3.5G communication module such as GPRS, UMTS or HSDPA module. GPRS/UMTS/ HSDPA module Mini PCI Express slot Mini PCI Express slot Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup 3. Push the module down then secure it with mounting screws. 4. Attach one end of the RF cable onto the module. Attach RF cable to the module Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup 5. The photo below shows one end of the RF cable properly attached onto the module. 6. Mount the other end of the cable to the antenna mounting hole located at the front panel of the chassis. RF cable mounted at the front panel Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup Installing a Wireless LAN Module 2. Insert the wireless LAN module into the Mini PCI Express slot at a 45 degrees angle until the gold-plated connector on the edge of the module completely disappears inside the slot. 1. The Mini PCI Express slot shown below is used to install a wireless LAN module. Wireless LAN module Mini PCI Express slot Mini PCI Express slot Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup 3. Push the module down then secure it with mounting screws. 4. Attach one end of the RF cable onto the module. Attach RF cable to the module Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup 5. The photo below shows one end of the RF cable properly attached onto the module. 6. Mount the other end of the cable to the antenna mounting hole located at the front panel of the chassis. RF cable mounted at the front panel Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup Installing a Bluetooth Module 2. Install the provided mounting stud as shown in the illustration below. 1. The USB header shown below is used to install a Bluetooth module. Mounting stud USB header Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup 3. Insert the Bluetooth module’s cable connector into the USB header. 4. Attach one end of the RF cable onto the module. Push the module down then secure it with a mounting screw. Attach RF cable to the module Mounting screw 5. Mount the other end of the cable to the Bluetooth mounting hole located at the front panel of the chassis. Bluetooth module Cable connector Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup Installing a CompactFlash Card 2. With the CompactFlash card’s label facing up, position the card to the socket. 1. Locate for the CompactFlash socket on the board. CompactFlash card CompactFlash socket Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup 3. Insert the card until it is completely seated in the socket. Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup Installing the PCI-104 Module 2. Position the PCI-104 module above the slot then press it down firmly until it is completely seated in the slot. This will at the same time align the module’s mounting holes to the mounting studs on the board. 1. Locate for the PCI-104 slot on the board. PCI-104 module Mounting hole PCI-104 slot Mounting stud Mounting stud Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup 3. Secure the module with mounting screws. Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup Installing a SATA Hard Drive · During Windows XP OS installation, press “F6”to select and install the SATA driver. 1. The metal bracket is used to hold a SATA hard drive. First, remove the screws that secure the metal bracket to the board then remove the bracket. · If you intend to install a Windows XP SP2 or earlier version, you must first set the “USB 2.0 Controller” field (in the BIOS) to Disabled. · By default, the “Legacy USB Support” field (in the BIOS) is Disabled.
Chapter 3: System Setup 3. Tighten the mounting screws to secure the HDD brackets in place. 4. Now place the SATA drive on the metal bracket then tighten the head bolt screws to secure the drive on the metal bracket. Head bolt screw HDD bracket HDD bracket Metal bracket Screwdriver Top View HDD bracket HDD bracket Screwdriver Bottom View Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup 5. Align the head bolt screws with the mounting studs on the board. Tighten the head bolt screws to secure the drive to the chassis. 6. Locate for the SATA connector and the power connector. on the board. Mounting stud Power connector SATA connector Head bolt screw Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup 8. Connect one end of the SATA power cable to the SATA power connector that is on the board then connect the other end of the cable to the SATA power connector at the rear of the SATA drive. 7. Connect one end of the SATA data cable to the SATA connector that is on the board then connect the other end of the cable to the SATA connector at the rear of the SATA drive. SATA data cable Cable connected to the SATA connector on the board Copyright © 2009 NEXCOM International Co., Ltd.
Chapter 3: System Setup Installing the SODIMM 2. Insert the module into the socket at an approximately 30 degrees angle. Apply firm even pressure to each end of the module until it slips into the socket. The gold-plated connector on the edge of the module will almost completely disappear inside the socket. 1. Remove the heatspreader’s mounting screws. SODIMM socket Heatspreader SODIMM Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup 3. Push the module down until the clips on both sides of the socket lock into position. You will hear a distinctive “click”, indicating the module is correctly locked into position. Clip Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup Installing the USB Cable Holder 2. Hook the cable to the holder as shown in the photo below. The USB cable holder is used to stabilize the USB cable so as to prevent it from getting loose when accidentally pulled or moved. 1. Attach the cable holder to the mounting hole by using the provided screw. Cable holder Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Chapter 3: System Setup Rackmount Brackets 2. Now mount the system on the wall by fastening screws through the bracket’s mounting holes. The rackmount brackets provide a convenient and economical way of mounting the system on the wall. 1. The mounting holes are located at the bottom of the system. Secure the brackets on each side of the system using the provided mounting screws.
Appendix A: I/O Address Function APPENDIX A: I/O ADDRESS FUNCTION Capacity of NEXCOM battery (8 bits) I/O port : 0EE1H GPIO LED / UMTS LED / Ignition Status I/O port : 0EE0H Bit Bit 0 Bit 1 Bit0 Function Description Description GPIO LED 0: OFF (default) 1: ON Ignition (read only) 0: OFF 1: ON Bit 3 Status of Vehicle Battery 0: Vehicle Battery is OK 1: Vehicle Battery is Low Voltage Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix A: I/O Address Function Status of NEXCOM battery (8 bits) I/O port : 0EE3H GPIO I/O port : 0EE4H Bit Function Description Bit Bit 0 Status for G sensor detection 0: Normal 1: Abnormal (X-axis or Y-axis degree is about 90 or -90) Bit 0-3 GPO 1-4 Bit 4-7 GPI 1-4 Bit 1 Power mode 0: 24V system 1: 12V system Bit 2 Fan mode 0: Auto 1: Always on Bit 3 Status of Smart battery 0: No discharging 1: Discharging Bit 4 Status of Fan R 0: Well 1: Failed Bit 5 Status of Fan R 0: Action 1: In
Appendix A: I/O Address Function WDT I/O port : 0EE5H Bit Bit 3 Onboard Module Disable/Enable I/O port : 0EE6H Function Description WDT Disable/Enable 0: Disable (default) 1: Enable Bit 2, 1, 0: Time Setting Bit 2~0 Time (sec) 000 1 (default) 001 2 010 4 011 8 100 16 101 32 110 64 111 128 Bit Function Description Bit 0 3.
Appendix B: ICES200-L24 COM Express CPU Module APPENDIX B: ICES200-L24 COM EXPRESS CPU MODULE Overview Key Features ICES 200 is a Type 2 COM Express Module that features Intel® 945GME and ICH7M chipset; switch supports Intel® Core™ 2 Duo and Intel® Core™ 2 Duo LV processors with 533/667 MHz FSB. One DDR2 memory socket supports up to 2GB. The ICES 200 is integrated with Intel® Graphics Media Accelerator (GMA950) and expands via PCI Express Graphics x16 lanes to the carrier board.
Appendix B: ICES200-L24 COM Express CPU Module Specifications Display · Integrated with Intel® Graphics Media Accelerator (GMA950) or expand via PCI Express Graphics x16 lanes / Dual SDVO · CRT resolution up to 2048 x 1536 @ 60Hz, 1600 x 1200 @ 85Hz · One PCI Express x16 Lane down to the carrier board · Supports LFP (Local Flat Panel) LVDS interface with resolution up to 1366 x 768 · Supports Single channel for 18 bit / Dual Channel for 18 bit CPU Support · Supports Intel® Socket M, Core™ 2 Duo Family Pr
Appendix B: ICES200-L24 COM Express CPU Module Dimensions · COM Express Basic Module Type 2 · 95mm x 125mm Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix B: ICES200-L24 COM Express CPU Module Mechanical Dimensions Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix B: ICES200-L24 COM Express CPU Module PCI Routing Slot / Device Signal Slot / Device 0 Slot / Device 1 Slot / Device 2 Slot / Device 3 IDSEL AD20 AD21 AD22 AD23 INTA# IRQA IRQB IRQC IRQD INTB# IRQB IRQC IRQD IRQA INTC# IRQC IRQD IRQA IRQB INTD# IRQD IRQA IRQB IRQC COM Express Module Connector Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix B: ICES200-L24 COM Express CPU Module Connectors Row A Row B Row A Row B A13 GBE0_MDI0+ B13 SMB_CK A68 PCIE_TX0+ B68 PCIE_RX0+ A14 GBE0_CTREF B14 SMB_DAT A69 PCIE_TX0- B69 PCIE_RX0- A15 SUS_S3# B15 SMB_ALERT# A70 GND B70 GND A16 SATA0_TX+ B16 SATA1_TX+ A71 LVDS_A0+ B71 LVDS_B0+ A17 SATA0_TX- B17 SATA1_TX- A72 LVDS_A0- B72 LVDS_B0- A18 SUS_S4# B18 SUS_STAT# A73 LVDS_A1+ B73 LVDS_B1+ A19 SATA0_RX+ B19 SATA1_RX+ A74 LVDS_A1+ B74 LVDS_B1- A2
Appendix B: ICES200-L24 COM Express CPU Module Row A Row B Row A Row B A40 USB4+ B40 USB5+ A95 RSVD B95 VGA_I2C_CK A41 GND B41 GND A96 GND B96 VGA_I2C_DAT A42 USB2- B42 USB3- A97 VCC_12V B97 NC A43 USB2+ B43 USB3+ A98 VCC_12V B98 NC A44 USB_2_3_OC# B44 USB_0_1_OC# A99 VCC_12V B99 NC A45 USB0- B45 USB1- A100 GND B100 GND A46 USB0+ B46 USB1+ A101 VCC_12V B101 VCC_12V A47 VCC_RTC B47 NC A102 VCC_12V B102 VCC_12V A48 EXCD0_PERST# B48 NC A1
Appendix B: ICES200-L24 COM Express CPU Module High Speed Board-to-Board Connector: COM Express Row C and Row D Connector size: 2 X 110 = 220 Pins Connector location: J1 Row C Row D Row C Row D C13 IDE_IORDY D13 IDE_A0 C68 PEG_RX5+ D68 PEG_TX5+ C14 IDE_IOR# D14 IDE_A1 C69 PEG_RX5- D69 PEG_TX5- C15 PCI_PME# D15 IDE_A2 C70 GND D70 GND C16 PCI_GNT2# D16 IDE_CS1# C71 PEG_RX6+ D71 PEG_TX6+ C17 PCI_REQ2# D17 IDE_CS3# C72 PEG_RX6- D72 PEG_TX6- C18 PCI_GNT1# D18 IDE_
Appendix B: ICES200-L24 COM Express CPU Module Row C Row D Row C Row D C40 PCI_AD19 D40 PCI_AD22 C95 PEG_RX13- D95 PEG_TX13- C41 GND D41 GND C96 GND D96 GND C42 PCI_AD21 D42 PCI_AD24 C97 RSVD D97 PEG_ENABLE# C43 PCI_AD23 D43 PCI_AD26 C98 PEG_RX14+ D98 PEG_TX14+ C44 PCI_C/BE3# D44 PCI_AD28 C99 PEG_RX14- D99 PEG_TX14- C45 PCI_AD25 D45 PCI_AD30 C100 GND D100 GND C46 PCI_AD27 D46 PCI_IRQC# C101 PEG_RX15+ D101 PEG_TX15+ C47 PCI_AD29 D47 PCI_IRQD# C
Appendix B: ICES200-L24 COM Express CPU Module PCIE 1X4 or PCIE 4X1 SWITCH SW1 ON 1 2 34 SW_DIP-2 Pin Status Config 1 and 2 OFF PCIE 4X1 1 and 2 ON PCIE 1X4 Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board APPENDIX C: VTCB6110 CARRIER BOARD Specifications I/O Interfaces - Front · 4 SMA-type mounting holes for WLAN, HSDPA and Bluetooth · 1 power button · 1 reset switch · 1 SIM card socket · 1 USB 2.0 · 4 LEDs for Standby, HDD, WLAN/HSDPA and GPO · 1 line-out · 1 mic-in Dimensions Expansion · 1 PCI-104 socket · 1 Bluetooth module (optional) · 2 Mini PCI Express socket - 1 PCIe interface for WLAN module - 1 PCIe + USB interface for 3.5G module Storage · One SATA 2.
Appendix C: VTCB6110 Carrier Board Jumpers and Connectors SW5SW4 SW2 SW7 CN15 J11 CN14 LED2 J13 SW3 J9 USB1 LED1 SW1 J2 J4 CN17 J1 CN4 JP6 J12 J3 Blue Tooth JP5 J7 JP4 JP8 10 J14 JP7 JP3 JP2 BZ1 3.5G CN16 JP1 CN6 WLAN J8 J10 CN12 CN9 CN7 SW6 J6 J5 CN5 LAN1 USB2 CN11 CN2 CON1 COM1 CN1 CN8 Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board LVDS Power Input Voltage Select (JP9) Jumper Settings Pin SW5: Input Voltage Selection SW5 / Input 12V (default) 24V 6V~36V SW5.1 OFF OFF ON SW5.2 OFF ON Ignore Voltage RS232 (default) OFF ON SW6.2 OFF ON SW6.3 OFF ON +5V IN +3.
Appendix C: VTCB6110 Carrier Board Temp Sensor (JP8) GAL Download (JP5) Pin Function Description Pin Function Description 1 SENSOR+ 1 +V3.3S 2 GND 2 GND Auto Power Select (JP2) 3 TCK 4 TDO Pin Status Function Description 5 TDI 1-2 (default) Short (default) AUTO 6 TMS 2-3 Short BUTTON CONTROL MCU COM Port (JP3) PCI-104 VI/O Select Voltage (J13) Pin Function Description Pin Status Function Description 1 TX 1-4(*) Short* +3.
Appendix C: VTCB6110 Carrier Board Connectors Row A Row B Row A Row B A13 GBE0_MDI0+ B13 SMB_CK A68 PCIE_TX0+ B68 PCIE_RX0+ A14 GBE0_CTREF B14 SMB_DAT A69 PCIE_TX0- B69 PCIE_RX0- A15 SUS_S3# B15 SMB_ALERT# A70 GND B70 GND A16 SATA0_TX+ B16 NC A71 LVDS_A0+ B71 NC A17 SATA0_TX- B17 NC A72 LVDS_A0- B72 NC A18 SUS_S4# B18 SUS_STAT# A73 LVDS_A1+ B73 NC C OME xp re ss A19 SATA0_RX+ B19 NC A74 LVDS_A1+ B74 NC MH 2 A20 SATA0_RX- B20 NC A75 LVDS_A2
Appendix C: VTCB6110 Carrier Board Row A Row B Row A Row B A40 USB4+ B40 USB5+ A95 RSVD B95 NC A41 GND B41 GND A96 GND B96 NC A42 USB2- B42 USB3- A97 VCC_12V B97 NC A43 USB2+ B43 USB3+ A98 VCC_12V B98 NC A44 USB_2_3_OC# B44 USB_0_1_OC# A99 VCC_12V B99 NC A45 USB0- B45 USB1- A100 GND B100 GND A46 USB0+ B46 USB1+ A101 VCC_12V B101 VCC_12V A47 VCC_RTC B47 NC A102 VCC_12V B102 VCC_12V A48 NC B48 NC A103 VCC_12V B103 VCC_12V A49 NC B4
Appendix C: VTCB6110 Carrier Board High Speed Board-to-Board Connector: COM Express Row C and Row D Connector size: 2 X 110 = 220 Pins Connector location: J3 Row C Row D Row C Row D C13 IDE_IORDY D13 IDE_A0 C68 NC D68 NC C14 IDE_IOR# D14 IDE_A1 C69 NC D69 NC C15 NC D15 IDE_A2 C70 GND D70 GND C16 NC D16 IDE_CS1# C71 NC D71 NC C17 NC D17 IDE_CS3# C72 NC D72 NC C18 NC D18 IDE_RESET# C73 NC D73 SDVO_CLK C19 NC D19 NC C74 NC D74 NC C20 PCI_GNT0# D20
Appendix C: VTCB6110 Carrier Board Row C Row D Row C Row D C40 PCI_AD19 D40 PCI_AD22 C95 PEG_RX13- D95 PEG_TX13- C41 GND D41 GND C96 GND D96 GND C42 PCI_AD21 D42 PCI_AD24 C97 RSVD D97 PEG_ENABLE# C43 PCI_AD23 D43 PCI_AD26 C98 PEG_RX14+ D98 PEG_TX14+ C44 PCI_C/BE3# D44 PCI_AD28 C99 PEG_RX14- D99 PEG_TX14- C45 PCI_AD25 D45 PCI_AD30 C100 GND D100 GND C46 PCI_AD27 D46 PCI_IRQC# C101 PEG_RX15+ D101 PEG_TX15+ C47 PCI_AD29 D47 PCI_IRQD# C102 PEG_RX1
Appendix C: VTCB6110 Carrier Board CompactFlash Connector Pin Connector size: 2 x 25 = 50 pins Connector location: J12 50 49 26 1 Connector Pin Definition Pin Description Pin Description 1 Gnd 2 Data 3 3 Data 4 4 Data 5 5 Data 6 6 Data 7 7 HDC CS100 8 Gnd 9 Gnd 10 Gnd 11 Gnd 12 Gnd 13 +5V 14 Gnd 15 Gnd 16 Gnd 17 Gnd 18 Disk Address 2 19 Disk Address 1 20 Disk Address 0 21 Data 0 22 Data 1 Copyright © 2009 NEXCOM International Co., Ltd.
Appendix C: VTCB6110 Carrier Board GPIO Connector RS232 Connector: COM1, COM2 Connector size: DSUB-9 pin Connector location: COM1 Connector size: 2 x 10 = 20 Pins Pin Header, (2.0 mm Pitch) Connector location: COM1 (CN9), COM2 (CN7) 5 CN10 1 9 1 3 5 7 9 6 BOX-2.
Appendix C: VTCB6110 Carrier Board RS232/485 Connector: COM3 GAL Programmer PIN Header Connector size: 2 x 10 = 20 Pins Pin Header, (2.0 mm Pitch) Connector location: CN12 Connector size: 2.54mm-M-180 Connector location: JP5 CN10 1 3 5 7 9 1 JP5 2 3 4 5 6 42 6 8 10 BOX-2.0mm-M-180 PIN-2.
Appendix C: VTCB6110 Carrier Board MCU Programmer Pin Header VGA Connector Connector size: 2.54mm-M-180 Connector location: JP6 Connector size: DSUB-15 Connector location: CON1 1 JP6 2 3 4 5 PIN-2.54mm-M-180 Connector Pin Definition Connector Pin Definition Pin Definition Pin Definition Pin Definition Pin Definition 1 1 +3.
Appendix C: VTCB6110 Carrier Board LVDS Connector + USB0 Pin Pin Definition 17 LVDS_5(OUT2) 18 Panel_backlight(+12V) 19 LVDS_4(OUT2#) 20 Panel_backlight(+12V) 21 LVDS_GND 22 Power on push buttom 42 6 8 23 USB_0# 24 USB_GND 25 USB_0 26 USB_VCC (+5V) 10 12 14 16 18 20 22 24 26 28 30 27 USB_GND 28 USB_GND 29 Panel_backlight(+12V) 30 GND Connector size: 2 x 15 (2.0mm) Connector location: CN3 CN3 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 Definition BOX-2.
Appendix C: VTCB6110 Carrier Board LAN Connector USB Connector Connector size: RJ-45 Connector location: LAN1 Connector location: USB1 Connector Pin Definition Connector Pin Definition Pin Definition Pin Pin Definition 1 TX+ 2 TX- 3 RX+ 4 N/C1 5 N/C2 6 RX- 7 N/C3 8 N/C4 9 LAN Speed LED 10 +3.3V LAN Link LED 12 +3.3V 11 Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board USB Connector LVDS Power Connector Connector location: USB2 Connector location: J5 1 Connector Pin Definition Connector Pin Definition Pin Pin Definition 1 Definition VCC 2 DATA1- 3 DATA1+ 4 GND 5 VCC 6 DATA- 7 DATA+ 8 GND Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board External 12V & 5V Power and SMBUS Connector Mic-in Connector location: CN2 Connector location: CN11 and CN15 6 4 3 1 Connector Pin Definition Connector Pin Definition Pin Pin Definition Pin Definition 1 5V 2 12V 3 SMBCLK 4 GND 5 GND 6 SMBDATA Definition Pin Definition 1 NC 2 MIC_JD 3 NC 4 MIC_OUT 5 GND 6 GND FOR AT&T NO This Function Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board Line-out PCI-104 VI/O Voltage Setting Connector location: CN8 and CN14 Connector location: J13 Connector Pin Definition Pin Definition Pin 1 LINE_OUT_L 2 SURR_JD 3 NC 4 LINE_OUT_R 5 GND 6 Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved. Definition 2 4 6 1 3 5 Connector Pin Definition GND 88 Pin No. Status Function Description 1-3, 2-4 (default) Short +3.
Appendix C: VTCB6110 Carrier Board PCI-104 Connector Power Button Connector location: CN16 Connector location: SW1 Connector Pin Definition Reset Button Connector location: SW2 Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board MCU COM Port ACC_ON LED Connector location: JP3 Connector location: JP7 Connector Pin Definition 1 Pin Function Description 1 TX 2 RX Pin Function Description 3 GND 1 +3.3V LED 2 GND Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board Temp Sensor DC Power Input Connector Connector location: JP8 Connector location: CN1 1 Connector Pin Definition Pin Connector Pin Definition Function Description 1 SENSOR+ 2 GND Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board Power On and IDE Active LED GPIO and UMTS LEDs Connector location: LED1 Connector location: LED2 T1 T2 B1 B2 LED I/O Port Address and Data Connector Pin Definition LED Function Description LED T1 POWER LED T2 I/O PORT Address: 0EE0; Bit0: 1 (Light), 0 (Dark) B1 HD LED B2 UMTS STATUS Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board Serial ATA Serial ATA Power Input Connector location: CN6 Connector location: J10 7 4 1 Connector Pin Definition Pin 1 Definition GND 1 Connector Pin Definition Pin Definition Pin Definition Pin 2 SATA_TXP0 - 1 +V12S 2 GND 3 GND 4 +V5S 3 SATA_TXN0 4 GND 5 SATA_RXN0 6 SATA_RXP0 7 GND Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix C: VTCB6110 Carrier Board Mini-PCIe Socket (for 3.5G module) PCIe Interface Mini-PCIe Socket (for WLAN module) USB + PCIe Interface Connector location: CN10 Connector location: CN13 2 52 2 52 1 51 1 51 Connector Pin Definition Pin Definition Pin Definition Pin Definition Definition Pin Definition Pin Definition 1 MIC + 2 +V3.3S 27 GND 28 NC 1 WAKE# 2 +V3.3S 27 GND 28 +V1.
Appendix C: VTCB6110 Carrier Board Bluetooth Connector Connector location: CN4 Connector location: J7 MH2 MH1 SIM Card Connector 1 2 3 4 5 6 7 8 10 9 J7 Pin Connector Pin Definition Pin Definition Pin Definition Pin GND 2 USB_6P_L Definition 3 USB_6N_L 4 NC NC 6 BT_AUDIO_EN_R BT_3.3V C1 POWER VOLTAGE C2 RESET SIGNAL 5 C3 CLOCK SIGNAL C5 GND 7 NC 8 I/O 9 NC 10 C6 VPP:PROGRAM VOLTAGE SW Contact present switch C7 Copyright © 2009 NEXCOM International Co., Ltd.
Appendix D: BIOS Setup APPENDIX D: VEHICLE POWER MANAGEMENT SETUP External Power Output Setting External +12V and +5V Turn Off Simultaneously External +12V and +5V Turn On Simultaneously Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix D: BIOS Setup External +12V Turn On Only Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix D: BIOS Setup Startup and Shutdown Voltage Setting 2. If the input voltage setting is 12V: set the startup voltage to 12V and the shutdown voltage to 11V. 1. If the input voltage setting is 12V: set the startup voltage to 11.5V and the shutdown voltage to 10.5V. If the input voltage setting is 24V: set the startup voltage to 24V and the shutdown voltage to 22V. If the input voltage setting is 24V: set the startup voltage to 23V and the shutdown voltage to 21V.
Appendix D: BIOS Setup 3. If the input voltage setting is 12V: set the startup voltage to 12.5V and the shutdown voltage to 11V. 4. If the input voltage setting is 12V: set the startup voltage to 12.5V and the shutdown voltage to 11.5V. If the input voltage setting is 24V: set the startup voltage to 25V and the shutdown voltage to 22V. If input voltage setting is 24V: set the startup voltage to 25V and the shutdown voltage to 23V.
Appendix D: BIOS Setup Power-on Delay Setting Enable Power-on Delay Disable Power-on Delay Delay time can be set at 10sec/30sec/1min./5min./10min./15min./30min./ 1hour. Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix D: BIOS Setup Power-off Delay Setting Disable Power-off Delay Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix D: BIOS Setup Enable Power-off Delay Delay time can be set at 20sec/1min./5min./10min./30min./1hour/6hour/ 18hour. Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Appendix E: Power Consumption APPENDIX E: POWER CONSUMPTION OS: XP English Burn-in Software: Version 5.0 Idle Mode 100% Burn-in Mode S3 S4 S5 1.47A / 12V 2.76A / 12V 0.11A / 12V 0.01A /12V 0.01A /12V * Device: N/A Copyright © 2009 NEXCOM International Co., Ltd. All Rights Reserved.
Federal Communications Commission (FCC) Statement 15.21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. 15.105(b) Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
FCC RF Radiation Exposure Statement: 1.This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2.This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
