NMCB101C RF Module User Manual V1.
Content 內容 Preface ..........................................................................................................................................................3 RF Module Overview ................................................................................................................................10 Introduction........................................................................................................................................10 RF module form factor ..............
Preface This manual is for WLAN service providers or network administrators to set up a network environment using the IWF series Product line. It contains step-by-step procedures and graphic examples to guide MIS staff or individuals with slight network system knowledge to complete the installation. Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved.
one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna, For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.
NEXCOM RoHS Environmental Policy and Status Update NEXCOM is a global citizen for building the digital infrastructure. We are committed to providing green products and services, which are compliant with European Union RoHS (Restriction on Use of Hazardous Substance in Electronic Equipment) directive 2011/65/EU, to be your trusted green partner and to protect our environment. RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg) < 0.1% or 1,000ppm, Cadmium (Cd) < 0.
▪▪ A Philips screwdriver ▪▪ A flat-tipped screwdriver ▪▪ A grounding strap ▪▪ An anti-static pad Using your fingers can disconnect most of the connections. It is recommended that you do not use needle-nose pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors. Safety Precautions 1. Read these safety instructions carefully. 2. Keep this User Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS. Technical Support and Assistance 1. For the most updated information of NEXCOM products, visit NEXCOM’s website at www.nexcom.com. 2.
Warning: Information about certain situations, which if not observed, can cause personal injury. This will prevent injury to yourself when performing a task. Caution: Information to avoid damaging components or losing data. Note: Provides additional information to complete a task easily.
RF Module Overview Introduction The NMCB101C RF module is designed for the user to implement cost effective solution to wireless sensor network products. The standard mPCI-e form factor makes it easy to install and fix in the embedded board. Key Features: - Integrate an ARM Cortex M4 MCU with on chip memory. - Support GPIO, UART, I2C, I2S and SPI buses. - Firmware down load through SWD. - Low power consumption. - Hardware WAPI acceleration engine.
Mini PCIe pin definition Logical symbol of RF module Pin description PIN Definition PIN Definition 1 Debug UART TXD 2 V3P3 3 NC 4 GND 5 NC 6 NC 7 NC 8 NC 9 GND 10 NC 11 NC 12 CPIO Power control 13 SPI_SCK 14 GND 15 GND 16 GPIO_IRQ 17 Debut UART RXD 18 GND 19 NC 20 RST_N 21 GND 22 NC 23 NC 24 V3P3 25 NC 26 GND
27 GND 28 NC 29 GND 30 NC 31 SPI_MISO 32 NC 33 SPI_MOSI 34 GND 35 GND 36 SWD_TMS 37 NC 38 SWD_TCK 39 NC 40 GND 41 NC 42 NC 43 NC 44 NC 45 NC 46 NC 47 NC 48 NC 49 Smart Command UART TXD 50 GND 51 Smart Command UART RXD 52 V3P3 System block diagram
Installation The installation of RF module is very easy. Just follow the steps below and you can complete the installation: Insert the radio module into mini PCIe slot in the PCBA. Screw up to fasten the module tightly inside PCBA. Note: The mini PCIe pin definition is different from standard mini PCIe module in other Wi-Fi application. The embedded PCBA should follow the mini PCIe pin definition to design the pin assignment to connect this radio module.
@10% PER -MCS=2PER @ -82dBm, typical -MCS=3PER @ -80dBm, typical -MCS=4PER @ -77Bm, typical -MCS=5PER @ -73dBm, typical -MCS=6PER @ -71dBm,typical -MCS=7PER @ -69dBm, typical Receive Sensitivity (11g) @10% PER -6MbpsPER @ -86Bm, typical -9Mbps PER @ -85dBm, typical -12MbpsPER @ -85dBm, typical -18MbpsPER @ -83dBm, typical -24MbpsPER @ -81dBm, typical -36MbpsPER @ -78Bm, typical -48MbpsPER @ -73dBm, typical -54Mbps PER @ -72dBm, typical 802.
Voltages (Absolute Maximum Ratings ) Recommended Operating Ratings
