802.11a/b/g/n Industrial WiFi module EWF3210K User Manual-QIG V1.
Preface This manual is for WLAN service providers or network administrators to set up a network environment using the IWF series Product line. It contains step-by-step procedures and graphic examples to guide MIS staff or individuals with slight network system knowledge to complete the installation. Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved.
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help.
This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 20 cm is maintained between the antenna and users, and The transmitter module may not be co-located with any other transmitter or antenna, For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change.
RoHS Compliance NEXCOM RoHS Environmental Policy and Status Update NEXCOM is a global citizen for building the digital infrastructure. We are committed to providing green products and services, which are compliant with European Union RoHS (Restriction on Use of Hazardous Substance in Electronic Equipment) directive 2011/65/EU, to be your trusted green partner and to protect our environment. RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg) < 0.1% or 1,000ppm, Cadmium (Cd) < 0.
Ensure you have a stable, clean working environment. Dust and dirt can get into components and cause a malfunction. Use containers to keep small components separated. Adequate lighting and proper tools can prevent you from accidentally damaging the internal components.
qualified service personnel. 14. If one of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the user’s manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. Do not place heavy objects on the equipment. 16.
cloth. Cautions Electrostatic discharge (ESD) can damage system components. Do the described procedures only at an ESD workstation. If no such station is available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis. Conventions Used in this Manual Warning: Information about certain situations, which if not observed, can cause personal injury. This will prevent injury to yourself when performing a task.
Contents
1. Introduction EWF3210K is QCA9344-based industrial-grade AP/CPE/Router/EZ MESH AP designed with IEEE802.11a/b/g/n 2x2 MIMO technology. EWF3210K can deliver data rate up to 1.16Gbps. In addition, the Radio power can be up to 27dBm for wide range coverage and service.
2. Interface WAN LAN DC 12V Package Contents ● EWF3210K 802.11a/b/g/n Industrial WiFu Module x1 3. System Information 3.1 Config setting To access the system to configuration, launch the web browser on your computer, and enter the device IP address in the Address field of the web browser. The factory default IP address: 192.168.1.1. A login screen will appear. Go to the login page by Click the “Login” Login ID and password is not required before access the system web user’s interface.
3.2 System status-Overview Click Status button to see information 3.3 System status-Routes Click Status button to see information 3.4 System status-System Log Click Status button to see information 3.5 System status-Kernal Log Click Status button to see information 3.6 System status-Processes Click Status button to see information 3.
4. System Configuration 4.1 System Click System button to see information 4.2 System Administration Click Administration button to see information and change the user name and password here. 4.3 System-Software Click Software button to see information. Code version 4.
5. Network Configuration 5.1 Network-Interfaces Click Network button to see information. Edit Ethernet 10/100/100 setting Edit Device IP setting 5.2 Network-WiFi Click Network button to see information. Edit 802.11 a/b/g/n setting Edit 1x1,2x2 MIMO setting Edit Radio channel setting Edit Radio bandwidth as NT20, HT40 5.3 Network-Switch Click Network button to see information.
6. Antenna information: Antenna Model UEN-203RSMA Type Connector Dipole R-SAM Peak gain ( dBi ) 2400~2483.5 5150~5250 5250~5350 5470~5725 5725~5850 MHz MHz MHz MHz MHz 5.7 dBi 4.35 dBi X X 5.
