mimioPad_QSG.
Copyright © 2008 Sanford, L.P. All rights reserved. No part of this document or the software may be reproduced or transmitted in any form or by any means or translated into another language without the prior written consent of Sanford, L.P. Trademarks mimio and mimio Studio are trademarks or registered trademarks of Sanford, L.P. All other trademarks are the property of their respective holders. mimioPad_QSG.
Congratulations on your mimio Pad purchase! mimio Pad is a 2.4 GHz wireless pad. To configure mimio Pad for use, install the mimio Studio software and plug the wireless receiver into your computer. Once connected, you can use the mimio Pad from anywhere in the room to interact with your computer. No additional configuration is required. Unpacking your mimio Pad 1. 2. Unpack the contents of your mimio Pad package. Make sure you have all the items shown below.
Become familiar with the features of your mimio Pad as shown in the following illustrations. Pad USB connection Pen slot Page up/ Page down Volume up/Volume down Power button LCD Shortcut keys Active area Front Learning button Wireless receiver storage Battery compartment (extra pen tips and tip extractor) Back Wireless Receiver Learning button/LED 2 mimioPad_QSG.
Getting Started Your mimio Pad is installed at the same time you install mimio Studio. Follow these instructions to begin using your mimio Pad. Inserting the Pad Battery 1. 2. 3. Press down and slide off battery compartment cover. Insert the battery. Replace the battery compartment cover. Charging the Battery The pad battery is charged using the included USB cable. The Li-ion pad battery may contain some charge right out of the box.
Inserting the Pen Battery The pen uses one AAA battery. 1 1. 2. 3. 2 3 Twist the top of the pen counterclockwise. Lift the battery cover, and insert battery as shown. Replace battery cover and pen top. Configuring the mimio Pad 1. 2. 3. 4. Plug the wireless receiver into a USB port on your computer. Press and hold the power button on the pad for at least three seconds to turn on the power. Place the pen tip anywhere on the active area of the pad to wake up the pad.
Using the mimio Pad The feature indicators on the LCD display are described below. mimioPad_QSG.indd 5 Power The power is on. Battery Indicator Shows how much charge is left in the pad battery. Power Saving Mode Power saving mode is on. The pad enters power saving mode when the pen is away from the active area for three seconds. Connected The pad is connected to your computer. Wireless Activity The wireless receiver is active.
Using the Shortcut Keys Shortcut keys are available across the top of the active area of the pad. These keys allow you to quickly access features in mimio Studio. Refer to the mimio Studio User Guide for a complete description of all mimio Studio features. Selection Tool Screen Clipping Pen Screen Annotation Highlighter Text Tool Eraser Spotlight Tool Cut Reveal Tool Copy Notebook Paste Tools New Page Recorder 6 mimioPad_QSG.
Changing the Pen Tip After a period of use, you may need to replace the pen tip. Extra pen tips and a pen tip extractor are located inside the pad battery compartment. 1 1. 2. Tip Extractor 2 Squeeze the pen tip with the tip extractor, and then pull out to remove the tip. Push the new tip into the pen, and then press the pen tip down on a hard surface to secure. Pairing an Additional Pad with the Wireless Receiver 1. 2. 3. mimioPad_QSG.
mimio Pad Specifications Interface Wireless 2.4 GHz RF Dimension 11.3x11.0x0.8 inches Active Area 7.84x5.92 inches Resolution 2000 lpi Report Rate 120 rpst Pen Pressure 1024 levels Shortcut Keys 16 Hot Keys Page up / Page down Volume up/Volume down LCD Type TN LCD LCD Size 0.7x1.6 inches Battery Type 3.
The R&TTE Directive We, the manufacturer, hereby declare that this equipment, model RCK-T07, is in compliance with the essential requirements and other relevant provisions of Directive 1995/5/EC. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
mimioPad_QSG.indd 10 Produced by: mimio, Cambridge, MA 877-846-3721: www.mimio.com © 2008 Sanford, L.P. 800-1011_01 Rev. 05/08 82-919W01010-000v1.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
