NEWCONT NEWCONT 2.4GHz CORDLESS CALLER ID TELEPHONE WITH CALL WAITING 40 CHANNEL AUTOSCAN NTP-6304D OWNER'S MANUAL INSTALLATION AND OPERATING INSTRUCTIONS NEWCONT PLEASE READ THIS MANUAL CAREFULLY BEFORE USE. KEEP FOR YOUR REFERENCE. Made in China 2002.
Special Features C ongratulations on your selection of a quality NEWCONT product. With proper care and by following the setup and user instructions in this manual, this unit will provide you with years of trouble free service. NEWCONT is committed to providing quality products that fit your needs. We would like to have any comments or suggestions you might have on this product . You may mail your comments to: 40 Floor, Block C, Electronics science &Technology Bldg, Shennanzhonglu, Shenzhen , P.R.
Special Features Luminous LCD Screen - The LCD Screen emits light for 8 seconds every time you press any of the TELEPHONE KEYPAD buttons. HANDSET Ringer Volume Level - Select the ringer volume level (HI, LOW, OFF). HANDSET Volume Control Switch - Select the receiver volume level(HI.MID,LOW). HEADSET JACK - Your telephone can utilize a headset for hands-free communication BELT CLIP- Use the BELT CLIP to hang your HANDSET on your belt.
HANDSET Controls Notes IMPORTANT In order to get maximum life from the HANDSET battery pack, be sure to charge the HANDSET for 12 hours before initial use. 1. HANDSET ANTENNA 2.NEW CALL/MESSAGE WAITING LED INDICATOR IMPORTANT 9. VOLUME CONTROL (HI, MID, LOW) SWITCH 3.LARGE LCD SCREEN NEW CALL MSG WAITING LDCCF CALLS BATT MSG DIR Placing your BASE UNIT near appliances such as televisions, refrigerators, radios, or microwave ovens may cause interference. 10.
Technical Information HANDSET Controls Technical Information 1.HANDSET ANTENNA This cordless telephone uses radio frequencies to allow mobility. There are certain difficulties in using radio frequencies with a cordless telephone. While these are normal, the following could after operation of your system. 2.
Problem Solving BASE UNIT CONTROLS Problem Solving section For your assistance, we have listed below a few common problems. Phone does not work, check the following: 1. BASE UNIT is plugged into power source. 2. HANDSET is charged. 3. TONE/PULSE Select switch is in the right position. 4.TELEPHONE LINE CORD is plugged in the TELEPHONE JACK. 1. TELEPHONE LINE CONNECTION JACK 2. POWER-IN CONNECTION JACK 3. TONE/PULSE SELECT SWITCH Range of phone limited, check the following: 1.
Changing the Battery Pack BASE UNIT CONTROLS Changing the BATTERY PACK 1. TELEPHONE LINE CONNECTION JACK The BATTERY PACK provides power for the HANDSET of your cordless telephone. 2. POWER-IN CONNECTION JACK 3. TONE/PULSE Select Switch To Replace the BATTERY PACK: 1. Remove the HANDSET BATTERY COMPARTMENT COVER by sliding it down. 2. Pull out the BATTERY CONNECTOR PLUG and remove the BATTERY PACK. 4. ANTENNA: Raise or reposition for the best reception. 5.
Contents Recharging the Battery Pack Safety Instructions............................................................................................................3 Battery Type Getting Started................................................................................................................. 5 Use the following type and size of BATTERY PACK: Cordless Telephone BATTERY PACK 3.6V, 600mAh Cordless Telephone Operation..........................................................................
Security Contents NOTES: 1. You can store a maximum of 16 characters on the letter icon. 2. You can store a maximum of 16 digits on the number icon. Saving in the Phone Book.............................................................................15 Security System Blocked Calls................................................................................................
Safety Instructions IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of fire, electric shock and /or injury, always follow these basic safety precautions when using your cordless telephone equipment. 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the telephone. 3. Do not use this telephone near a bathtub, kitchen sink, wash bowl, laundry tub, in a wet basement, near a swimming pool, or anywhere else where there is water. 4.
Caller ID System Operation Safety Instructions I .VOICE MAIL E. If the telephone has been dropped or the case has been damaged. F. If the telephone exhibits a distinct change in performance. 16. Never install telephone wiring during a lighting storm. 17. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 18. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 19.
Getting Started Connecting Your Phone This section is a reference guide to the basic functions and operations of your cordless telephone. For more detailed descriptions of the operations and features of this telephone, refer to the Contents on page 1. 1. Carefully remove your cordless telephone from its shipping carton. If there is any visible damage, do not attempt to operate this equipment. Return it to the place of purchase. 2.
Caller ID System Operation 6. Press the / VOICE MAIL button to return to the STANDBY mode. NOTE: The date and time will automatically set, if you have subscribed to the Caller ID service from your local telephone company. D. RINGER VOLUME This function enables you to adjust the ringer volume from HI, LOW and OFF as desired. 1. Press the / VOICE MAIL button and hold down. 2. Press the TELEPHONE KEYPAD 3. Press the EDIT GHI SAVE 2. Press the TELEPHONE KEYPAD button. /FLASH button. 4.
Getting Started Caller ID System Operation A. LANGUAGE HANDSET TALK This telephone offers English, Spanish and French languages for your convenience. 1. Press the / VOICE MAIL button and hold down. 2. Press the TELEPHONE KEYPAD 3. Press the LDCCF AM PM Press the TALK button to confirm that you have a dial tone. If you do not get a dial tone, review steps 3 through 12. If you still do not have a dial tone, refer to the Problem Solving section on page 30.
Caller ID System Operation Cordless Telephone Operation Function Operation Preparing for Use This unit contains the following special functions: Before you can use cordless telephone ,you must charge the HANDSET for 12 hours. Failure to do so will require recharging of the BATTERY PACK more often. (See page 26 for more information on the BATTERY PACK) A. LANGUAGE F. AREA CODE B. FIRST RING ON/OFF G. FLASH TIME C. TIME SET H. PAUSE TIME D. RINGER VOLUME I. VOICE MAIL E. LCD CONTRAST J.
Cordless Telephone Operation Caller ID System Operation Deleting All Records in the PHONE BOOK Placing Calls 1. Press the TALK button, the Call Timer starts to count. The HANDSET LCD Screen will display "CALLS " and "TALK ", and the BASE UNIT IN USE LED indicator will light up. 1. Press the DIR button to enter the phone book list. (If the phone book is not full, the LCD screen will disply "NEWDATA", press scroll UP or DOWN to enter the phone book list) 2.
Caller ID System Operation Cordless Telephone Operation Placing Calls from the PHONE BOOK Using the Headset Feature 1. Press the Your telephone can utilize a headset (not included) to be connected to your HANDSET for you to enjoy hands-free communication. Insert the small plug at the end of the headset into the HEADSET JACK at the right side of the HANDSET. Follow the procedures discussed in "Receiving Calls "and" Placing Calls" to receive and place a call. DIR button. 2.
Caller ID System Operation Caller ID System This telephone automatically displays an incoming caller's name and telephone number together with the date and time of the call. It records up to 80 calls and stores the data in Memory. IMPORTANT: You must subscribe to the Caller ID service from your local telephone company to utilize this feature. Caller ID System Operation Editing the Name and Number in the PHONE BOOK 1. press the button. DIR 2.
Caller ID System Operation Caller ID System Operation Speed Viewing the PHONE BOOK Call Waiting 1. Press the When you subscribe to a Call Waiting service from your local telephone company, this telephone will display the name and number of the second caller while you are having a phone conversation with your first caller. 1. When you are having a conversation ,this tele- e.g. phone will automatically display the name and number of the second caller. The name will be blinking. 2.
Caller ID System Operation Viewing the Caller List 1. Press the SCROLL DOWN button to view the latest Caller ID record, or press the SCROLL UP button to view the first Caller ID record, press the SHIFT RIGHT button if the name has more than 11digits. Caller ID System Operation Deleting All Records in the Caller List 1. Press and hold down the DEL /SCAN button while in the caller list, and display "ERASE ALL" 2.