Installation Guide

ManualsBrandsNewAge Products ManualsStorage & Organization33 in. H x 26 in. W x 16 in. D Ready-to-Assemble Metal 3-Drawer Tool Cabinet in Grey

Install InstructIons

READ THIS FIRST BEFORE UNPACKING CABINET

24 GAGE STEEl RTA TOOl CABINET

DO NOT lEAvE CHIlDREN UNATTENDED NEAR CABINETS.

WHEN FUlly lOADED, CABINETS ARE HEAvy AND THERE IS A

RISK OF CABINETS OR ITEmS TIPPING IF ImPROPERly OPENED.

CABINET SHOUlD BE mOUNTED TO WAll TO AvOID INjURy

WARNING:

ExCESSIvE WEIGHT HAzARD

• Use two or more people to move, assemble or install cabinet or

locker.

• Failure to do so can result in back or other injury.

UNPACKING OF THE CABINET:

• Begin by placing the cabinet on a sound level surface.

• Remove all cardboard and foam packaging material.

• Remove clear plastic bag.

• Dispose / recycle all packaging materials.

• Remove and verify all the contents in the box. See “Parts and

Hardware Supplied List”

WARNING:

DO NOT OvERlOAD CABINETS!

CABINETS ARE DESIGNED

TO CARRy THE FOllOWING

mAxImUm WEIGHT

CAPACITIES:

Cabinet Shelf Weight

Capacity (lbs)

Overall Weight

Capacity

Locker 50 200

Wall 40 80

Base 50 150

Tool 30 150

need more information? try, WWW.NEWAGEPRODUCTS.COm or 1 877 306 8930 for answers to commonly asked questions.

PARTS AND HARDWARE SUPPlIED

WITH BASE CABINET:

QTy ITEm ImAGE

1 Locking Rod

47 M5 Frame Screw

47 M5 Frame Nut

4 Adjustable Leg

16 M8 Leg Screws

16 M8 Leg Screw Nut

18 M8 Large Washer

16 Lock Washers

2 2.5” Wall Screw

4 5/8” Wood Screw

All CABINETS mUST BE mOUNTED TO STUDS ON A SECURE WAll, AS PER THESE

INSTRUCTIONS. FAIlURE TO DO SO mAy RESUlT IN SERIOUS INjURy AND vOIDS

PRODUCT WARRANTy AND mANUFACTURER’S lIABIlITy.

Summary of content (7 pages)

PAGE 1
24 Gage Steel RTA tool Cabinet Install Instructions READ THIS FIRST BEFORE UNPACKING CABINET All cabinets must be mounted to studs on a secure wall, as per these instructions. Failure to do so may result in serious injury and voids product warranty and manufacturer’s liability.
PAGE 2
4 Gage Steel RTA Tool Cabinet Install Instructions E A C B G D G G F A G B Z Y X Left Back Panel Right Back Panel C Drawer Components D W Right Panel Left Panel W E X F Drawer Front Panel Top Panel Bottom Panel G x3 Drawer Z Drawer Back Support Panel for Drawer Front Y Drawer Bottom need more information? try, www.NewAgeProducts.com or 1 877 306 8930 for answers to commonly asked questions.
PAGE 3
24 Gage Steel RTA Tool Cabinet Install Instructions 1. Use the M5 screw and M5 nut to 2. Assemble the left and right assemble the two back panels. side panel with the same screw and nut. D Goes on the outside of A, and C goes on the outside of B. B C D A 4. Flip the cabinet over. Use M8 screw, washer and M8 nut to assemble the adjustable legs on the bottom panel. 3. Panel E sits on the outside of A and B, and on the inside of C and D. Do the same for panel F. 5.
PAGE 4
24 Gage Steel RTA Tool Cabinet Install Instructions Y Z W X Z W Drawer assembly: X Y **Below is what it will look like when Z has fit into the notches along the side and bottom of Y. 1) Bend the two sides of DRAWER BOTTOM (Y) upwards to create the side walls. Notch a Notch 3. Insert the edge without the ridge of DRAWER PANEL (W) at the other side of DRAWER BOTTOM (Y). You may use a mallet to apply force. Note: Drawer bottom must rest on the inside of DRAWER PANEL (W).
PAGE 5
24 Gage Steel RTA Base Cabinet Install Instructions Assembly Instructions: Cabinet Leveling (for all cabinets except for wall cabinet) 1. Place a small magnetic level onto the top of the cabinet to verify the levelness of the cabinet. 2. If the floor slopes and the cabinet is not level, lift the adjustable sleeve on the leg and adjust the cabinets height-adjustable leveling leg by turning the nut on top of the cabinet’s foot, up or down to bring the cabinet to a level position.
PAGE 6
24 Gage Steel RTA Tool Cabinet Install Instructions Mounting Cabinets into Drywall / Studded Wall: Warning: All cabinets must be mounted to studs before loading the cabinets with items Each locker or base cabinet must be mounted to the wall with at least two of the provided mounting screws. Each wall cabinet must be mounted with four screws. 1. Using a stud finder locate the studs in the wall where the wall cabinet is to be placed. 2.
PAGE 7
NewAge Products Inc. Steel Cabinetry Warranty 1 year limited manufacturer warranty For one year from the date of purchase, when this product is installed, operated and maintained according to the instructions attached to or furnished with the product, NewAge Products Inc. will replace the defective product or parts if the part fails as a result of defective materials or workmanship. NewAge Products Inc. will not pay for: 1.