Installation Manual

ManualsBrandsNew Centurion Solutions ManualsElectronicsHANDHELD SECURITY DEVICE

THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO NEW CENTURION SOLUTIONS, INC. AND SHALL NOT BE

REPRODUCED OR DISCLOSED IN WHOLE OR IN PART FOR ANY DESIGN OR MANUFACTURE EXCEPT WHEN SUCH USER

POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM NEW CENTURION SOLUTIONS, INC.

Elliott Tech, LLC

IREP Installation Manual

IREP

New Centurion Solutions

Project Number: 776

Reference: 776-91-06-REV-IREP_INSTALLATION_MANUAL.docx

Original Document: March 1, 2011

Revision A: March 16, 2011

Prepared for:

Prepared by:

New Centurion Solutions, Inc.

Greg Williams

3011 Spring Garden St.

Suite E

Greensboro, NC 27403

(336) 617-5410

GWilliams@newcenturionsolutions.com

Elliott Tech, LLC

346 Raleigh Street

Holly Springs, NC 27540

(919) 342-6899

(888) 631-1795 Fax

s.elliott@elliotttech.com

Summary of content (6 pages)

PAGE 1
Elliott Tech, LLC IREP Installation Manual IREP New Centurion Solutions Project Number: 776 Reference: 776-91-06-REV-IREP_INSTALLATION_MANUAL.docx Original Document: March 1, 2011 Revision A: March 16, 2011 Prepared for: New Centurion Solutions, Inc. Greg Williams 3011 Spring Garden St. Suite E Greensboro, NC 27403 (336) 617-5410 GWilliams@newcenturionsolutions.com Prepared by: Elliott Tech, LLC 346 Raleigh Street Holly Springs, NC 27540 (919) 342-6899 (888) 631-1795 Fax s.elliott@elliotttech.
PAGE 2
IREP Installation Manual 776-91-06-REV-A_IREP_INSTALLATION_MANUAL.docx Revision Page Rev A Description FCC Notification Section 3 THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO NEW CENTURION SOLUTIONS, INC. AND SHALL NOT BE REPRODUCED OR DISCLOSED IN WHOLE OR IN PART FOR ANY DESIGN OR MANUFACTURE EXCEPT WHEN SUCH USER POSSESSES DIRECT, WRITTEN AUTHORIZATION FROM NEW CENTURION SOLUTIONS, INC.
PAGE 3
IREP Installation Manual 776-91-06-REV-A_IREP_INSTALLATION_MANUAL.docx Contents 1. Equipment List ......................................................................................................... 4 2. Installation Prerequisties ........................................................................................ 5 3. Installation Instructions .......................................................................................... 5 4. FCC Notification ..................................
PAGE 4
IREP Installation Manual 1. 776-91-06-REV-A_IREP_INSTALLATION_MANUAL.docx EQUIPMENT LIST A. Antenna, helical short ¼ wave (1) B. IREP Assembly (1) C. Double-gang box installation (pre-requisite) D. #6-32 pan head screw (4) – included with IREP assembly E. #6-32 x 1” button-head screw (1) – included with IREP assembly THE INFORMATION CONTAINED HEREIN IS PROPRIETARY TO NEW CENTURION SOLUTIONS, INC.
PAGE 5
IREP Installation Manual 2. 776-91-06-REV-A_IREP_INSTALLATION_MANUAL.docx INSTALLATION PREREQUISTIES Ensure that the following installation prerequisite is met:  3. Wiring and installation of double-gang box INSTALLATION INSTRUCTIONS To begin, check the parts available against the equipment list, identifying any missing parts. If all parts are accounted for, proceed to the instructions below to begin installing the IREP. Step 1 Step 1: Identify the Antenna, helical short ¼ wave (A).
PAGE 6
IREP Installation Manual 776-91-06-REV-A_IREP_INSTALLATION_MANUAL.docx Step 3: Identify the #6-32 pan head screw (D). Ensure that the outer half of the enclosure is detached from the inner half. Secure the inner half of the IREP (connected to wires) assembly to the double-gang box with four of these screws. Step 3 Step 4: Identify the outer half of the IREP enclosure. Secure this half over the first half using the #6-32 x 1” button-head screw (E) at the top center of the IREP. Step 4 4.