DMI-2 Bedienungsanleitung digitales Mikrophon-Interface Operating Instructions Digital Microphone Interface georg neumann gmbh · ollenhauerstr. 98 · 13403 berlin · germany fon +49 (0)30 / 41 77 24-0 · fax -50 · headoffice@neumann.com · www.neumann.
1. Reparatur- und Servicearbeiten dürfen nur von erfahrenem und autorisiertem Fachpersonal durchgeführt werden. Wenn Sie die Geräte eigenmächtig öffnen oder umbauen, erlischt die Gewährleistung. Einleitung In dieser Anleitung finden Sie alle wichtigen Informationen für den Betrieb und die Pflege des von Ihnen erworbenen Produktes. Lesen Sie diese Anleitung bitte sorgfältig und vollständig, bevor Sie das Gerät benutzen.
• Auch bei externer Synchronisation bleibt der interne Clock Generator (VCXO) wirksam und wird mittels einer PLL auf den externen Word Clock synchronisiert. Hierdurch wird eine sehr effektive Jitter-Unterdrückung erreicht. AES 42 In 3-poliger XLR-Eingang zum Anschluss eines digitalen Mikrophons. AES/EBU Out 3-poliger XLR-Ausgang für das AES/EBU-Ausgangssignal. Zulässige maximale Kabellänge in Abhängigkeit von der gewählten Abtastrate s. Kapitel „XLR-Kabel“.
Starten Sie die RCS – gegebenenfalls erneut, falls das Programm noch geöffnet war. Achtung: Das DMI-2 muss immer eingeschaltet sein, bevor die RCS gestartet wird, damit das DMI-2 vom PC/Mac erkannt wird. Solange die RCS arbeitet, darf das Verbindungskabel zwischen Computer und USB 485-Konverter nicht abgezogen werden, um ein unkontrolliertes Verhalten des Computers zu vermeiden. Dies ergibt sich aus der Spezifikation der USB-Schnittstelle.
8.4 Synchronisation Der Standard AES 42 beschreibt zwei Arten der Synchronisation des Mikrophons mit dem Empfänger (z.B. Mischpult oder Digitales MikrophonInterface – DMI-2): Mode 1: Das Mikrophon arbeitet unsynchronisiert mit der Abtastrate seines internen Quarzoszillators und benötigt auf der Empfängerseite einen Abtastratenwandler (Sample-Rate-Converter).
1. Repairs and servicing are to be carried out only by experienced, authorized service personnel. Unauthorized opening or modification of the equipment shall void the warranty. Introduction This manual contains essential information for the operation and care of the product you have purchased. Please read the instructions carefully and completely before using the equipment. Please keep this manual where it will be accessible at all times to all current and future users.
AES 42 In This is a 3-pin XLR input for connecting a digital microphone. purpose. This permits use of the plug-and-play capability of available USB ports together with the much longer cable lengths (at least 100 m) that are possible with an RS 485 connection. The pins can be controlled via contact with ground, or alternatively by means of logic outputs (TTL logic level). For example, in the case of muting, the mute can be activated and the red LED switched off via a single contact (e.g.
Start the RCS program, or if necessary restart it, if the program was already on. Attention: The DMI-2 must always be switched on before the RCS is started, so that the DMI-2 will be detected by the PC or Mac. While the RCS is operating, the cable connecting the computer to the USB 485 converter must not be disconnected, so as to prevent uncontrolled behavior of the computer. This requirement is due to the specifications of the USB interface.
8.4 Synchronization The AES42 standard describes the following two modes for synchronizing the microphone with the receiver (e.g. a mixing console or the DMI-2 Digital Microphone Interface). Mode 1: The microphone operates asynchronously, using the sampling rate of its internal quartz oscillator. In this case, a sample rate converter is required at the receiver.
Word Clock IN Digital Mic. OUT Receiver AES42 AES/EBU Control Data + DPP Control Data DPP(+10V) Control Bus Abb. 1 / Fig. 1 Abb. 3 / Fig. 3 Abb. 2 / Fig. 2 Control Device (Computer) (e.g. Mix.
® Konformitätserklärung Declaration of Conformity Die Georg Neumann GmbH erklärt, dass dieses Gerät die anwendbaren CE-Normen und -Vorschriften erfüllt. Neumann ist in zahlreichen Ländern eine eingetragene Marke der Georg Neumann GmbH. Georg Neumann GmbH hereby declares that this device conforms to the applicable CE standards and regulations. Neumann is a registered trademark of the Georg Neumann GmbH in certain countries.