User manual Washer Dryer IWD 601 W
Contents Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3 Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 Washing programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8 Drying Programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11 First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 13 Personalisation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 1
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. • The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa) • The ventilation openings in the base (if applicable) must not be obstructed by a carpet. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused.
• Use this appliance in a household only. • Do not change the specification of this appliance. • Do not put flammable products or items that are wet with flammable products in, near or on the appliance. • Do not touch the glass of the door while a programme operates. The glass can be hot. • Make sure that you remove all metal objects from the laundry. • The final part of the drying cycle occurs without heat (cool down cycle) to ensure that the items will not be damaged.
Product description 1 Detergent dispenser drawer 2 Control panel 1 2 3 Door opening handle 4 Rating plate 5 Drain pump 6 Adjustable feet 3 4 5 6 Child safety Make sure that children or pets do not climb into the drum. To prevent children and pets becoming trapped inside the drum this machine incorporates a special feature. To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin.
Compartment for liquid additives (fabric softener, starch). Follow the product manufacturer’s recommendations on quantities to use and do not exceed the «MAX» mark in the detergent dispenser drawer. Any fabric softener or starching additives must be poured into the compartment before starting the wash programme. Control panel On the following page there is a picture of the control panel. It shows the programme selector dial as well as the buttons, pilot lights and the display.
people who are allergic to detergents, and in areas where the water is very soft. Drying Time If you wish to carry out a timed drying programme, press this button until the drying time you want appears on the display according to the fabrics (cottons or synthetics) you have to dry. For Cottons you can select a drying time from 10 minutes to 250 minutes (4.10). For Synthetics you can select a drying time from 10 minutes to 130 minutes (2.10).
• Alarm codes In the event of operating problems, some alarm codes can be displayed, for example paragraph «What to do if...»). (see • Incorrect option selection If an option which is not compatible with the set wash programme is selected, the message Err is displayed at the bottom of the display for a few seconds and the integrated red light of button 7 start flashing.
Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Fabrics Load Type of Laundry Delicates 40°- Cold Main wash - Rinses Short spin at 700 rpm Max. load kg 3 - Reduced. load kg 1,5 2) Delicate fabrics: acrylics, viscose, polyester. Options Detergent Compartment RINSE HOLD SUPER QUICK EXTRA RINSE Jeans 40° Main wash - Rinses Long spin at 1200 rpm Max.
Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Fabrics Load Type of Laundry Detergent Compartment Options Drain Draining of water Max. load 7 kg For emptying out the water of the last rinse in programmes with the Rinse Hold option selected. Spin Drain and long spin Long spin at maximum speed Max. load 7 kg Separate spin for hand washed garments and after programmes with the Rinse Hold option selected.
Degree of Drying Type of Fabric Drying Load Spin Speed Suggested drying time in Minutes Suitable for ironing Cotton and linen (sheets, tablecloths, shirts, etc.) 4 kg 3 kg 1.5 kg 1200 130-150 90-100 60-70 1) In compliance with EC directive and EN 50229 the cotton reference programme for the data entered in the Energy Label must be tested dividing the maximum washing load by two equal parts and drying with DRYING TIME each of them. First cycle drying time: 180 min.
• powder detergents for delicate fabrics (60°C max) and woollens • liquid detergents, preferably for low temperature wash programmes (60°C max) for all types of fabric, or special for woollens only. The detergent and any additives must be placed in the appropriate compartments of the dispenser drawer before starting the wash programme. If using liquid detergents, a programme without prewash must be selected.
• = Do not tumble dry. Drying cycle duration The drying time may vary depending on: • speed of the final spin • dryness degree required (iron dry, store dry) • type of laundry • weight of the load size . The average drying time for a timed drying are indicated in the «Drying programmes» chapter. The experience will help you to dry your laundry in a more suita- ble way, according to the different fabrics. Take note of the duration drying time of the already performed cycles.
Daily Use Load the laundry Open the door by carefully pulling the door handle outwards. Place the laundry in the drum, one item at a time, shaking them out as much as possible. Close the door. Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the laundry. Measure out the detergent and the fabric softener Pull out the dispenser drawer until it stops.
Important! If an incorrect option is selected, the message Err is displayed for a few seconds and the red pilot light of this button blinks 3 times. then to the new programme position. Start the new programme by pressing button 7 again. The washing water in the tub will be not emptied out. Select the Delay Start by pressing button 8 Before you start the programme, if you wish to delay the start, press this button to select the desired delay.
Remove the laundry from the drum and carefully check that the drum is empty. If you do not intend to carry out another wash, close the water tap. Leave the door open to prevent the formation of mildew and unpleasant smells. Stand by : once the programme has finished after a few minutes the energy saving system will be enabled. The brightness of the display is reduced. By pressing any button the appliance will come out of the energy saving status.
If possible, do not select a spin speed lower than that proposed by the appliance to avoid too long a drying time therefore saving energy. 4. In any case the reduction of the spin speed is only possible after selecting drying. The lowest values you can select are 900 r.p.m. for cottons and synthetics and 700 r.p.m. for delicate fabrics. Set the drying time by pressing button 5. The display shows the whole duration of the washing and the set drying cycle.
Cleaning the drawer recess Having removed the drawer, use a small brush to clean the recess, ensuring that all washing powder residue is removed from the upper and lower part of the recess. Replace the drawer and run the rinse programme without any clothes in the drum. Cleaning the pump The pump should be inspected regularly and particularly if: • the appliance does not empty and/or spin; • the appliance makes an unusual noise during draining due to objects such as safety pins, coins etc.
Cleaning the water inlet filters Important! If the appliance doesn't fill, takes long to fill with water, the starting button blinks yellow or the display (if available) shows the relevant alarm (see chapter "What to do if..." for more details), check if the water inlet filters are blocked . To clean the water inlet filters: • Turn off the water tap. • Unscrew the hose from the tap. • Clean the filter in the hose with a stiff brush. • Screw the hose back onto the tap. Make sure the connection is tight.
What to do if... Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below.
Problem Possible cause/Solution The machine does not empty and/or does not spin: The drain hose is squashed or kinked. E20 • Check the drain hose connection. The drain filter is clogged. E20 • Clean the drain filter. An option or a programme that ends with the water still in the tub or a that eliminates all the spinning phases has been selected. • Select the draining or spinning programme. The laundry is not evenly distributed in the drum. • Redistribute the laundry.
Problem Possible cause/Solution The machine vibrates is noisy: The transit bolts and packing have not been removed. • Check the correct installation of the appliance. The support feet have not been adjusted • Check the correct levelling of the appliance. The laundry is not evenly distributed in the drum. • Redistribute the laundry. Maybe there is very little laundry in the drum. • Load more laundry.
Problem The laundry is full of different colored fluff Possible cause/Solution The fabrics washed in the previous cycle released fluff of a different colour (refer to “Fluff in the garments” in chapter ‘Use - Washing & Drying’). • The drying phase helps to eliminate some fluff. • Clean the clothes with a fluff remover. In case of an excessive amount of fluff in the drum repeat the following procedure twice: • Thoroughly clean the empty drum, the gasket and the door with a wet rag. • Perform a rinse cycle.
Maximum Dry Load Cotton Cotton Big Capacity Synthetic 3 Kg 4 Kg 2 Kg Spin Speed Maximum 1200 rpm Consumption values Programme Energy consumption (KWh) Water consumption (litres) Programme duration (Minutes) Cottons 60° 1.35 67 Cotton Energy Saving Programme 60° 1) 1.05 49 Cottons 40° 0.85 67 For the duration of the programmes, please refer to the display on the control panel. Synthetics 40° 0.55 42 Delicates 40° 0.55 63 Wool/ Handwash 30° 0.
To help prevent vibration we recommend you place a waterproof wood panel, at least 15 mm thick under the appliance, secured to at least 2 floor beams with screws, the wood panel must extend beyond the front feet. If possible install the appliance in one of the corners of the room, where the floor is more stable. Water inlet Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet.
Caution! The inlet hose must not be lengthened. If it is too short and you do not wish to move the tap, you will have to purchase a new, longer hose specially designed for this type of use. Warning! Installation should comply with local water authority and building regulations’ requirements. The appliance must be connected to a cold water supply. A minimum water pressure of 0.05 MPa (0.5 bar) is required for safe operation of the appliance.
If the outlet spigot has not been used before, remove any blanking plug that may be in place. Push the drain hose onto the spigot and secure with a clip, ensure a loop is formed in the drain hose (see above) to prevent waste from the sink entering the appliance. If you intend to drain the hose from the machine into a sink, make sure that the sink is empty and the plug hole is not blocked. Use the plastic “U - Piece” supplied.
Caution! Do not remove the screw 8! Preparation and assembly of the door The machine is originally prearranged for the assembly of a door opening from right to left. In this case it is sufficient to screw in the hinges (1) and the counter-magnet (6) provided with the appliance, at the right level (Fig. B). 35 Ø 12,5-14 depth 16-22 B C 416 22±1,5 C 595-598 • a) Door The dimensions of the door should be: - width 595-598 mm - thickness 16-22 mm The height (C-Fig.
d) Counter-magnet (6) The appliance is prearranged for a magnetic closure of the door. To enable a correct operation of this device, it is necessary to screw the counter-magnet (6) (steel disk + rubber ring) into the inner side of the door. Its position must correspond to the magnet (4) on the appliance (see picture D). Where the appliance has been raised by mounting onto a wooden base provided by the installer.
Graphic H Hardwood strip 5 mm x 25 mm 5 x 25 x 605 490 600-605 Fix the base firmly to the floor using four appropriate countersunk screws (see Fig. H). With the appliance installed adjust all four feet ensuring the machine is stable, and a clearance of approximately 5 mm is left between the top of the machine and the underside of the worktop. A final check for stability should be carried out with the machine on spin with a load, this will identify the need for any further fine adjustment to the feet.
deal with minor faults and how to take care of your product. When contacting us for Service please ensure that you have proof of purchase and the following information available: Model No . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Date of Purchase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Customer Care: Please contact Electrolux Major Appliances, Addington Way, Luton, Bedfordshire, LU4 9QQ Contact No: 08445 613613 Product No . . . . . . . . . . . . . . .
132912860-A-262013