User manual Dishwasher IDSH602W
Contents Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Product description _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Programmes _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Options _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Before first use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 4 4 5 5 6 Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8 Hints and tips _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10
Warning! Dangerous voltage. If the water inlet hose is damaged, immediately • disconnect the mains plug from the mains socket. Contact the Service to replace the water inlet hose. Use • This appliance is intended to be used in household and similar applications such as: – Staff kitchen areas in shops, offices and other working environments – Farm houses – By clients in hotels, motels and other residential type environments – Bed and breakfast type environments.
Product description 1 2 10 9 8 7 6 5 4 3 1 Upper spray arm 2 Lower spray arm 6 Rinse aid dispenser 7 Detergent dispenser 3 Filters 4 Rating plate 8 Cutlery basket 9 Lower basket 5 Salt container 10 Upper basket Control panel 1 2 4 1 On/off button 2 Programme indicators Indicators 3 3 Indicators 4 Programme button. Description End indicator. Salt indicator. This indicator is off while the programme operates.
Programmes Degree of soil Type of load Programme 1) 2) 3) 4) Programme phases Duration (min) Energy (kWh) Water (l) Normal soil Crockery and cutlery Prewash Wash 50 °C Rinses Dry 195 1.02 11 Normal soil Crockery and cutlery Prewash Wash 65 °C Rinses Dry 100 - 110 1.2 - 1.6 15 - 16 Heavy soil Crockery, cutlery, pots and pans Prewash Wash 70 °C Rinses Dry 130 - 150 1.3 - 1.4 13 - 15 Fresh soil Crockery and cutlery Wash 65 °C Rinse 30 0.8 9 All Prewash 14 0.
• The programme indicator flash. starts to 5. Wait until the programme indicator goes off. The programme indicator continues to flash. 6. Press the programme button. The end indicator comes on. The acoustic signal for the end of programme is activated. 7. Press the on/off button to deactivate the appliance and to confirm the setting. 2. Press the programme button. The end indicator goes off. The acoustic signal for the end of programme is deactivated. 3.
Adjusting the water softener Water softener adjustment Water hardness German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Level 47 - 50 84 - 90 8.4. - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.0 28 - 35 6 19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1) 15 - 18 26 - 32 2.6 - 3.2 18 - 22 4 11 - 14 19 - 25 1.9 - 2.5 13 - 17 3 4 - 10 7 - 18 0.7 - 1.
Filling the salt container 1. 2. 3. 4. 5. Turn the cap counterclockwise and open the salt container. Put 1 litre of water in the salt container (only for the first time). Fill the salt container with dishwasher salt. Remove the salt around the opening of the salt container. Turn the cap clockwise to close the salt container. Caution! Water and salt can come out from the salt container when you fill it. Risk of corrosion. To prevent it, after you fill the salt container, start a programme.
Using the detergent A 30 B 1. 2. 3. D 20 4. C Using the combi detergent tablets When you use tablets, that contain salt and rinse aid, do not fill the salt container and the rinse aid dispenser. The rinse aid indicator always comes on if the rinse aid dispenser is empty. 1. Adjust the water softener to the lowest level. 2. Set the rinse aid dispenser to the lowest position.
Important • Let the dishes become cold before you remove them from the appliance. Hot dishes can be easily damaged. • First remove the items from the lower basket, then from the upper basket. • There can be water on the sides and on the door of the appliance. Stainless steel becomes cool more quickly than the dishes. Hints and tips The water softener Hard water contains a high quantity of minerals that can cause damage to the appliance and bad washing results.
Cleaning the filters C B 1. Turn the filter (A) counterclockwise and remove it. 2. To disassemble the filter (A), pull apart (A1) and (A2). Remove the filter (B). Wash the filters with water. Before you put the filter (B) back, make sure that there are no residues of food or soil in or around the edge of the sump. A A1 3. 4. 5. A2 6. 7. Make sure that the filter (B) is correctly positioned under the 2 guides (C). Assemble the filter (A) and put it back in filter (B).
Alarm code Problem • The end indicator flashes 1 time intermittently. • Acoustic signal sounds 1 time intermittently. The appliance does not fill with water. • The end indicator flashes 2 times intermittently. • Acoustic signal sounds 2 times intermittently. The appliance does not drain the water. • The end indicator flashes 3 times intermittently. • Acoustic signal sounds 3 times intermittently. The anti-flood device is on. Warning! Deactivate the appliance before you do the checks.
Technical information Dimensions Width / Height / Depth (mm) Electrical connection Refer to the rating plate. Voltage 596 / 818 -898 / 555 220 - 240 V Frequency 50 Hz Water supply pressure Min. / max. (bar / MPa) (0.5 / 0.05 ) / (8 / 0.8 ) Water supply 1) Cold water or hot water2) Capacity Place settings 12 Power consumption Left-on mode 0.50 W Off-mode 0.50 W max. 60 °C 1) Connect the water inlet hose to a water tap with a 3/4'' thread.
156971460-B-372013