PARTS CHECK LIST BEFORE ASSEMBLE, PLEASE MEASURE YOUR PIPE FOR A CLEARANCE OF EITHER 5 INCH BELOW OR 9 INCH ABOVE. OR THE SPACE SAVER WILL NOT FIT PROPERLY. The NEU HOME logo is a registered United States trademark of ORGANIZE IT ALL, INC.
– BEFORE ASSEMBLY, USE THE CHECK LIST ON THE INSTRUCTION SHEET TO COUNT ALL PARTS AND HARDWARE TO ENSURE ALL PARTS AND HARDWARE ARE PRESENT. – PLEASE BE SURE TO WORK ON A SOFT, FLAT SURFACE TO AVOID ANY DAMAGE TO THE FINISH. – YOU NEED AT LEAST 2 PEOPLE TO FINISH THE ASSEMBLY OF THIS PRODUCT. HARDWARE CHECK LIST Power Drill and Screwdriver required for assembly. Not included. CAUTION: When use power drill, do not over- tighten the screws.
OVERVIEW
Assemble the top unit - Before assemble, make sure the grooves of (Part 18, Part 6 and Part 19) is facing inward. - Insert 2 Dowels (Part j) into holes along edge of Top Support (Part 18). - Attach Top Support (Part 18) and Bottom Support (Part 19) with Right Side Panel (Part 6) by Screws (Part a). - Cover screw head with Stickers (Part p). Caution: When use power drill, do not over- tighten the screws. - Insert Back Panel (Part 20) into grooves. (Unfinished (raw) side of back panel face down.
Assemble the door - Attach the magnet plate (Part O) to Door Panels (Part 16 and Part 17) with Screws (Part e). - Insert (Part k) to the edge of Door Panels (Part 16 and Part 17). Reminder, make sure insert the longer side of (Part k) into the hole. - Attach magnet (Part n) to Top Panel (Part 1) with Screw (Part e). - Place Top Panel (Part 1). Do not tighten up. - Align the Door Panels (Part 16 and Part 17) into the holes of Top Panel (Part 1) and Bottom Shelf (Part 4).
Assemble the Panel Support , Long Dowel and Cam Bolt Note: Insert Long Dowel (Part i) through Bottom Panel (Part 2) and Bottom Support (Part 19) Helpful Hint: Insert Cam Bolt (Part g) into position. See figure below: . DO NOT OVERTIGHTENED SCREWS. Assemble Side Posts Helpful Hint: Insert Cam Bolt (Part f) into position.
Assemble the Side Support Push Short Dowels (Part j) to Upper Side Supports (Part 11). Push Short dowels (Part j) to Bottom Side Supports (Part 12). Assemble the Side Frame. Tighten Cam Locks. - Carefully align Cam Bolt with holes in edge of Upper Side Supports (Part 11). - Slowly push Upper Side Supports (Part 11) into Side posts. - For tightening Cam Lock, use the flat screwdriver. - Repeat above steps and assemble Bottom Side Supports (Part 12). - Cover Cam Lock with Stickers (Part s).
Assemble the Supports - Attach Back Up Support (Part 14) and Front Support (Part 13) by Screws (Part a). - Cover screws head with Sticker (Part p). Assemble the Back Supports - Bring complete unit over the toilet. - Attach Back Support (Part 15) by Screws (Part a). - Cover screws head with Sticker (Part p).
Attach the Top Unit with Bottom Unit. Tighten Cam lock. - Carefully align all Dowels and Cam Bolt with holes in edge of assembled product. - Slowly push Top Unit into place. - For tightening Cam Lock (Part h), Use the flat screwdriver. - Cover Cam Lock by Stickers (Part s). Helpful Hint: Install Cam Locks - Identify arrow on head. - Arrow must point toward hole in edge of panel. - Push Cam Lock all the way down into hole.
Attach unit to the wall - Mark holes (AA) on the wall. - Pre-drill holes with a 7mm(0.28”) drill bit before installing wall anchors (Part q) into the wall. - Install wall anchors. - Align holes and use Screws (Part c) to secure the unit. - Cover screw head with Stickers (Part p).
Insert Shelf to assembled unit. Place Shelf (Part 3) inside of cabinet.
The NEU HOME logo is a registered United States trademark of ORGANIZE IT ALL, INC.