Your property guardian at day and night Vigil Camera Quick Guide
Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
What’sInThe Box Yourproperty guardianatdayand night Vigil Camera Quick Guide Drilling Template Power Adapter X3 Quick Guide X3 Hex Key Mounting Screws Anchors Drill Bit Weatherproof Tube Antenna Vigil Camera
Installation Guide Catalogue 1. More About Vigil Camera 2. Read Before Installing P. 1-2 P. 3 3. Set Up with Netvue App P. 4-13 4. Vigil Camera Installation P. 14-21 5. Status Light P.
MoreaboutVigilCamera Infrared LEDs Lens Light Sensor Speaker Micro SD Card Slot Microphone Wi-Fi Configuration Button Ethernet Cable Port Status Light Power Port 1 Antenna
How to Insert Micro SD Card Vigil Camera comes with a built-in card slot which supports up to 128GB Micro SD card. Once you insert the storage card, the camera will automatically start to record and store videos on the storage card. Videos can be replayed by dragging the timeline below the live feed screen in Netvue App. Step 1: Loosen the screws. Takeoff the cover gently since wires are attaching to it. Step 2: Insert Micro SD card. Make sure you insert it in the correct direction.
Read Before Installing 1.KeeptheVigilCameraandallaccessoriesoutof reachofchildrenandpets. 2. Power supply voltage that is required to operate Vigil Camera should be 12VDC (≥1000mA). 3. The product can only be used in proper temperature and humidity: Operating temperature: -20°C - 50°C (-4°F-122°F) Operating humidity: 0-90%. 4. Please do not expose the camera lens to direct sunlight. 5. Please do not install the camera to the place that is likely struck by lightning. 6. Power Source: Corded-Electric 7. 2.
SetUp with Netvue App Please add the Vigil Camera onto your Netvue account through Netvue App before mountingit outside. Connecting Method There are two ways of adding Vigil Camera onto Netvue App: Wireless Connection and Wired Connection. Wirelessconnection Wireless connection uses Wi-Fi to connect the camera to the App. It is the easiest way if the installation spot is close to your router and have a strong Wi-Fi signal. Please note that thick or insulated wall may weaken the signal dramatically.
Wired connection If the Wi-Fi signal strength is weak at your installation spot, the Ethernet cableconnection mightbe yoursolution. An Ethernet cableis required for this connection method. Plug one end of the Ethernet cable into Vigil Cam, and the other end into the LAN port on your router. Then follow thein-appinstruction tocompletethefollowing setupprocess.
AddCameratoNetvue App 1. Power on Vigil Camera withthe providedpower adapter. Youshouldheara chimeonceithasfullystarted.
Download Netvue App 2.DownloadNetvueAppfromAppStore orGooglePlayontoyourphone.
3. Register an account if you are a new user to Netvue. If you already have an account, log into your account.
+ 4. Tap “+” at the top right corner to add a new device.
5. A product list will show up, choose “Vigil Camera.
please select network connection Wireless connect Wired connect CANCEL 6. Choose a connecting method.
please select network connection Wireless connect Wired connect CANCEL 7. Follow the in-app instruction to complete the entire set up process.
OUTDOOR OWNER AUTO HISTORY 8. Test the video streaming. Now move to Vigil Camera installation.
Vigil Camera Installation Check following things before you starting to drill holes on your wall: 1. Vigil Camera has been successfully added to your Netvue App and is able to stream video. 2. Have planned the cable route. Measured the length of the power cable and Ethernet cable (if you plan to use Ethernet connection) you will need.
Step 1: Take off the anti-dust cap. Attach the provided antenna to Vigil Camera.
Step 2: Find a good installation spot. We recommend installing the Vigil camera just 7-10 feet (2-3 meter) above the ground for a better two-way audio experience. There is a power outlet nearby. Test whether Vigil camera can stream video smoothly at the spot. Make sure nothing blocks the camera’s sight.
Step 3: Before you starting to drill, make sure you know the locations of wall-in pipes and electrical wires. (If you are not comfortable with drilling holes, please consult with a licensed electrician.) Install Camera on Concrete or Brick: Use the provided drilling template to mark the position of holes on your wall. Use the provided drill bit to drill three holes, and then install anchors to hold screws.
, , ‘‘· { : H © 、 吨叫 ‘吨同啕 ① 18
Install Camera on Wood: Use the provided drilling template to mark the position of holes on your wall. Directly tighten the included screws to secure the camera.
Step 4 (Wired Connection): Readthis stepif youare usingwiredconnection, otherwiseskip to Step5. This steprequires the skillof making an Ethernet cable. Consult with the electricianifyouarenotsurehowtodoit. A weatherproof tube is needed for Ethernet cable to avoid leaking water into Ethernet cable port. Cut off the Ethernet cable at the length you want. Insert the cable into the weatherproof tube, and carefully attach RJ-45 connector to the cut ends. Test the cable is working before installing.
Step 5: Use the hex key to loosen screws on the hinge. Point the camera to your designate direction, then tighten the screws.
Status Light Netvue Vigil Camera uses status light to communicate.
Feelfreetocontactusforadditionalhelp: support@netvue.com Chat with us through App 1(866)749-0567 @NetvueTech www.netvue.com 240 W Whitter Blvd Ste A, La Habra, CA 90631 © 2010-2018 Netvue Technologies Co., Ltd. All Rights Reserved. Version 1.
产品名称: 说明书尺寸: Vigil Camera 105mm*130mm 印刷颜色: 单色黑 材质: 装帧: 80g 书写纸 骑马钉(28 页) 日期: 设计师: 2018-03-05 加乔 设计文件须知 black magenta cyan yellow 1.此文件为 Netvue 市场部出品,请勿修改相关设计文件,如有修改请联系设计师 2.所有的文件需经相关部门负责人审核校对 2.设计师在交稿之前应对文件仔细校对以确保图纸准确性 3.