US EmberLux Switch User Manual EmberLux Switch Model: BLZ-US-01 Firmware: Hardware: V0.6 and below V1.0 and below 20150923 FW V0.1~V0.
Table of Contents 1. Introduction.............................................................................................................................................................. 2 2. Product Appearance.................................................................................................................................................3 3. Specification.....................................................................................................................................
1. Introduction Netvox BLZ-US-01 , a battery-powered wall switch, acts as an End Device in ZigBee network. It does not perform permit-join function as a coordinator or a router for other devices to join the network. BLZ-US-01 is featured to control the On/Off device or the dimmable device. What is ZigBee? ZigBee is a short range wireless transmission technology based on IEEE802.15.4 standard and supports multiple network topologies such as point-to-point, point-to-multipoint, and mesh networks.
2.
3. Specification Fully IEEE 802.15.4 compliant Utilizes 2.4GHz ISM band; up to 16 channels Power supply: 2 x AAA batteries Up to 70 meters wireless transmission range in non-obstacle space Easy installation and configuration Operation temperature: -10 ℃~ 50 ℃ 4. Installation This device is NOT truly waterproof/ resistant and is for indoor use. 5. Setting up BLZ-US-01 5-1.
command from Z970A. For example, after BLZ-US-01 binds with Z809B successfully, press control button of BLZ-US-01 the bind device Z809B will receive command and act correspondingly (including normal bind and group bind). A. On/Off control (0x0006) (1) Short press Button 1 (network indicator flash once for 0.5s)→ send the turn-on command. (2) Short press Button 2 (network indicator flash once for 0.5s)→ send the turn-off command. B.
5-5. Battery When the operating voltage is lower than 2.4V, BLZ-US-01 will send a low-power report to the ZigBee network. 5-6. Restore to Factory Setting To restore it to factory setting, please follow the steps: Step1. Remove the batteries to power off BLZ-US-01 . Step2. Press and hold the Reset Key, then power on BLZ-US-01 to complete the restore. 6. Home Automation Clusters for BLZ-US-01 A cluster is a set of related attributes and commands which are grouped together to provide a specific function.
0x0001 0x0002 0x0003 0x0004 0x0005 0x0006 0x0007 0x0010 0x0011 0x0012 ApplicationVersion Unsigned 0x00 – 8-bit integer 0xff Unsigned 0x00 – 8-bit integer 0xff Unsigned 0x00 – 8-bit integer 0xff Character 0 – 32 string bytes Character 0 – 32 string bytes Character 0 – 16 string bytes 8-bit 0x00 – Enumeration 0xff Character 0 – 16 string bytes PhysicalEnvironmen 8-bit 0x00 – t Enumeration 0xff DeviceEnabled Boolean 0x00 – StackVersion HWVersion Manufacture
0x0035 0x0036 0x0037 0x0038 0x0039 0x003e 8-bit integer 0xff write Bitmap 0000 Read / (8-bits) 000x write BatteryVoltageMinT Unsigned 0x00 – Read / hreshold 8-bit integer 0xff write BatteryVoltageThres Unsigned 0x00 – Read / hold1 8-bit integer 0xff write BatteryVoltageThres Unsigned 0x00 – Read / hold2 8-bit integer 0xff write BatteryVoltageThres Unsigned 0x00 – Read / hold3 8-bit integer 0xff write 32-bit 0x00… Bitmap x BatteryAlarmMask BatteryAlarmState
7. Netvox App control 1. Add device to Netvox system, the added device list will show up in device management as below, 2、Click “Setting” into device interface as below: Click “Pairing configuration” into binding interface. Click “Pair Devices ” (ex. LED dimmable light). Click “bind” on the right-top.(Note: before binding, users need to turn on ED for fear that ED is in sleeping mode which may cause binding fails.
After binding, BLZ-US-01 is able to control dimming switch to turn on/off and adjust brightness. If users want to unbind device, long press bind device item, message “unbind” will show up as below on the left as below. (Note: before clicking “unbind”, users need to turn on ED.) After unbinding completely, item will disappear.
8. ZiG-BUTLER 8-1. Join BLZ-US-01 into the network When ZiG-BUTLER sees a coordinator or a router device, it will show the icon. Right click on the icon of the coordinator or the router and choose Set Permit Join On. After BLZ-US-01 has successfully joined, the BLZ-US-01 icon will be appeared in ZiG-BUTLER. 8-2. Bind BLZ-US-01 (1) Right click on the End Point of BLZ-US-01 and select Bind.
(2) On the Device tab, select the device to which you would like to bind. Next, click Select ClusterID, choose the Cluster, and click OK. The information would be pop-up after the binding is completed. Note: to bind the device via Zig-butler, please make sure BLZ-US-01 is on. We suggest to turn on BLZ-US-01 before binding. (3) Right click on the End Point of BLZ-US-01 and select Properties to view the binding information.
8-3. Power Consumption Report (1) Right click on the End Point of BLZ-US-01 and select Properties to overview the power consumption. (2) In binding list, we can see bind request information of other devices. If bind device and BLZ-US-01 share the same cluster ID: 0001 of binding request. Then BLZ-US-01will report data to the bind device. Below figures shows alarming range of voltage. The default minimum alarming voltage is 2.4V.
(4) On the Device tab, select the device to which you would like to bind. Next, click Select ClusterID, choose the Cluster, and click OK. Choose bind device sharing the same cluster ID: 0001 of binding request through “device’. to choose cluster ID which is needed. (5) Right click on the End Point of BLZ-US-01and select Properties. (6) On the Report Config tab, check Auto to modify the settings. Click Set to complete the setting.
(7) Click set to customize: Min: the minimum reporting internal (second) Max: the maximum reporting internal (second) Reportable change: BLZ-US-01 reports data instantly when the change rate is more than this value.
Report setting interval table: Min Interval (Unit:second) 1-65534 0 1-65534 Max Interval (Unit:second) Reportable Change Change rate≥ Reportable Change Change rate< Reportable Change ≠0 To report per Minimum interval To report per Maximum interval 0 To report per Minimum interval To report per Minimum interval ≠0 To report instantly To report per Maximum interval 0 To report per second To report per second ≠0 To report per Minimum interval No report 0 To report per Minimum interval
9. Related Netvox Devices Z806: Output Unit ZC06: Dimmable LED Tube 10. Important Maintenance Instructions Please keep the device in a dry place. Precipitation, humidity, and all types of liquids or moisture can contain minerals that corrode electronic circuits. In cases of accidental liquid spills to a device, please leave the device dry properly before storing or using. Do not use or store the device in dusty or dirty areas. Do not use or store the device in extremely hot temperatures.
FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.