FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired aeration. Warning! This Equipment has been tested and found to comply with the limits for a class B digital device, Pursuant to Part 15 of the FCC rules.
1. Introduction Congratulations on the purchasing of your new 10/100 N Way Fast Ethernet PC) adapter. This document describes the network adapter Installation. This adapter supports Fast Ethernet and Wake-On-LAN features and complies with the electrical and protocol requirements of the PCI Local Bus Specification, Revision and 2.1. 1.1 Features The 10/100 Fast Ethernet PCI adapter 1 a cost effective, high-performance network interface card.
2. installation This section describes how to install the adapter. For connecting to the network, you must have the following: 1. Network adapter card installed to your computer. 2. Cabling {compatible with network topology) 3. Connect the Wake-On-LAN cable to the mother board (If the WOL is necessary) 4. Software for the adapter card contains both configuration utilities and drivers. 2.
2.2 install the Adapter 1. Turn off the computer. 2. Remove the computer's cover, in accordance to its manual. 3. Insert the contact edge of the adapter cred into the connector of any available PCf Bus master expansion slat. Press the card firmly into the connector ta PCI slot. Please make sure that the card's contacts are fully seated in the PCI slot 4. Install the bracket screw that secures the card to the Computer chassis. & Connect the WOL cable to the mother board, if the WOL. feature is required. 8.
2.3 Connect Fast Ethernet Category 5 UTP cable is required for Fast Ethernet operation. The maximum cable run between the adapter and the supporting hub is 300ft (100m). Make the network connection by plugging one and of the cable into the JR-45 receptacle of the adapter, and the other end into one port in the hub. S0s0EU ED 2.4 Connect 10Mbps Ethernet Category 3, Category 4, and Category 5 UTP cable. as well as EXPATIATE 568 100 ohm STP cable, all qualification under Ethernet cabling rules.
To wake up Target Machine with Magic Packet Step: Target Machine: Target Machine is necessary to use the WOL cable link the Wake On LAN connector on adapter with your motherboard. Check BIOS AC PI, Wake On LAN function must be enable. Step: Target Machine. Select then the system will setup makeup event and wait a magic packet to do system makeup Step: Master Machine: Select to send a magic packet and wake up the target machine.
After choosing the item, the screen will display like. Node ID... Network Speed... : 100Hbps 11/0 Base EO00H interrupter 1 11 Full-Duplex Disabled Pass Count Fail Count A. 1/0 Register B. 1008bps Loop back C. 10Mhps Loop back callable Connection> test reminds you that the connection fink might be fail. either the cable is not connected or the cable link fails.
Quick Installation Guide Please take the following steps for driver installation. Microsoft Windows 95/Windows Windows NT 1. Turn off the computer. 2. Insert the adapter into the available PCI slot 3. Restart the computer. 4. After Microsoft Windows reboot, the PCI Ethernet Controller will be found 5. The system will prompt for driver installation. 6. Insert the “Driver and Utilities diskette into diskette driver and press 7. The Windows stern will install the driver automatically.
2.5 Drivers and Utilities Diskette The [Divers and Utilities} diskette contains all the popular operating system drivers. Nov ell NetWare(client /server) NT 35 NT4.0 Windows 95/98 Microsoft Client (DIS 2.0 DOSSIER) Windows For Work group 3.11 . and so on 2.8 Software Installation Please refer to” Quick Installation Guide’ 2.7 Test Program This test program verifies configuration of the adapter and assists the isolation of any faults in operation.