© Cb rie i tn, sl 35x 2 Median seamanship FCC Statement This device compiles with Part 15 of the FCC Rules.
1. Introduction Congratulations on the purchase of your new N-Way 10/100M PCI Fast Ethernet adapter This document describes the N-w Way PCI Fast Ethernet adapter installation. N-Way 'G/1 DEBASE PCI Fast Ethernet adapter supports ABASE -T and 1QOBASE-TX Fast Internet. and complies with the electrical and protocol requirements of the PCI Local Bus Specification, Revision 2.0 and 2.° 7.
1.2 System Requirements To use the adapter you need the following components a A PC-based PC ® A PCI master mode expansion slot that is comp liar with the PCI local bus specifications. revisions 2.0 and 2.1 ® A 35-inch, 1.44MB diskette drive The following cables: To operate at 10Mbis.
LCI ¥ 2. Installation This section describes how to install the adapter. To be connected to a network, you must have the following: 1. Network adapter card installed to your computer. Cabling (compatible with network topology) Software for the adapter card containing both configuration and driver 2 3 2.1 Unpack and Inspect Caution: | Under ordinary circumstances, this adapter card will i not be affected by static charge as may be received through your bed curing handling of the unit.
rime tide as ar ira 2 darn habit aan ALL tbr 30 ana ork mbt 2.2 Prepare Driver Files ri After unpacking the adapter, insert the [Drivers and Utilities] diskette nto your flippy driver. Be tore you from inserting this adapter into your PC, yau should prepare tr driver files for network operation system. At your DCS prompt. type the following command. and press renter 2 The opening screen of the installation screen will appear. The program's mans are sited at the top of the screen.
ah Bes abbr o a ste Duenna fa ad faith 20 So SEE ALL 8 Select «Diagnose Program to do the diagnostics 7. Select to read the instructions for each network software installation Select «Quit> to return to DOS mode 3 Install The Adapter Turn off the computer and unplug its power cord. . Remove the computer's cover, in accordance to its manual Insert the contact? edge of the adapter card into the connector of any available PCI Bus master expansion slot.
reed 2.4 Connect Fast Ethernet Category 5 UTP cable is required for Fast Ethernet operation The maximum cable run between the adapter and the supporting tub is 300 # Make the network connection by plugging one end of the cable into the JR-45 receptacle of the adapter. and the other end into a port of the hub 2.5 Connect 10Mbps Ethernet Category 3, Category 4, and Category 5 UTP cable, as well as LETITIA 568 100 onm STP cable, alt qualify under Ethernet cabling rules.
2.6 Drivers and Utilities Diskette The [Drivers and Utilities] diskette contains the following network OS drivers Nov ell Wetware (client/server) NT 3.51, NT4.0 Windows 95 Client 32 Microsoft Client (STANDISH DOS) Window For Work group 3.11 ND 7 Software Installation Because many network environments in which the adapter may be installed, you can run "install exe” for the help about the frequency of revisions in those network systems, and the instructions for each network software installation. 2.
Tw 3 or After Windows 85 reboot, the PCI Ethernet Controller will be found. Please press button Because the driver files are in sub-directory Cavendish 25 instead of A Sloppy driver Please press < Other Locations» button. Please type the location that contains driver files ana press < OK > button to finish installation procedure. . Please refer to the other Windows 95 books for installation clients of network operating system, services and protocols.
2.9 Test Program This test program verifies configuration of the adapter as set by the installation procedure, and assists with isolation of any faults in operation. Test procedure are optional, and will only be useful in the unusual event that there is a fault, such as an interrupt number conflict among your computer's ad don cards. If your installation provides normal operation, you do not need these test procedures.
«Cable Connection> test reminds you that the connection link might be fail, either the cable is unplugged or the cable link fails. For the
Appendix LED and Connectors This figure shows the LED and connectors for the adapter, and Table A describes the LED status Green LED 4 Q ic Active) Green LED Link @ Lo sullied or Half Duplex) & f——— © Green i. BR.