User's Manual

ManualsBrandsNETIS SYSTEMS ManualsElectronicsADSL2+ MODEM WITH 150MBPS WIRELESS-N ROUTER



DL4304D

ADSL2+ Modem Plus 150Mbps

Wireless-N Router

Quick Installation Guide



1. Hardware Installation

Step1:ConnecttheADSLLine.

Methodone:Plugoneendofthetwisted‐pairADSLcableinto

the ADSL LINE port onthe rearpanelofthe router,andinsert

theotherendintothewallsocket.

Method two: You can use a separate splitter. The external

splitterhas

threeports:

•Line:Connecttothewalljack

•Phone:Connecttothephonesets

•Modem:ConnecttotheADSLLINEportoftherouter

Step 2: Connect the Ethernet cable. Attach one end of a network

cabletoyourcomputer'sEthernetportoraregularhub/switch

port,

andtheotherendtotheLANportontherouter.

Step3:PoweronthecomputersandLANdevices.

Step4:Attachthepoweradapter.Connect thepoweradaptertothe

powerconnectorontherearofthedeviceandplugintheadapterto

awalloutletorpowerextension.



Figure1



Name Status Indication

PWR On Powerison

Off Powerisoff



ADSL

Flash TheADSLnegotiationisinprogress

On TheLINEportislinkedup.

Off TheLINEportislinkeddown.



Internet

Flash DataisbeingtransferredovertheInternet.

On AsuccessfulPPPconnectionhasbeenbuilt.

Off

There is no successful PPP connection or the

RouterworksonBridgemode.



WLAN

Flash Thereiswirelessdatabeingtransmitted.

On The wireless function is enabled but no data is

beingtransmitted.

Off Thewirelessfunctionisdisabled.



LAN(1‐4)

Flash Dataisbeingtransferredoverthe1‐4(LAN)port.

On

There is a successful connection on the

corresponding1‐4(LAN)portbutnoactivity.

Off

There is no connection on the corresponding 1‐4

(LAN)portortheconnectionisabnormal.

Summary of content (4 pages)

PAGE 1
DL4304D ADSL2+ Modem Plus 150Mbps Wireless-N Router Quick Installation Guide 1. Hardware Installation Step 1: Connect the ADSL Line. Method one: Plug one end of the twisted‐pair ADSL cable into the ADSL LINE port on the rear panel of the router, and insert the other end into the wall socket. Method two: You can use a separate splitter.
PAGE 2
. Configure PC ForWindows 7 or Windows Vista as below. Step 1: Click , then select the Open Network and Sharing Center. Figure 4 Step 4: Double click the “Internet Protocol Version 4(TCP/IPv4)”. Figure 2 Step 2: Click the Change adapter settings. Figure 3 Step 3: Click Local Area Connection with the right button of your mouse. Then select Properties. Figure 5 4 5 Step 5: Select the “Obtain an IP address automatically” as below. Then click “OK”.
PAGE 3
click “ Add” wireless network parameters required to access the AP of your WLAN interface. Fourth: Click “Save” botton to make it effetive. Go to Setup->WLAN->Basic page, you can configure the wireless parameters. Here you may enable or disable the wireless function. You can also change the wireless parameters, such as Band, SSID, Channel Width, Control Sideband, Channel Number and Radio Power. Figure 9 5.
PAGE 4
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver.