Quick Start Guide NTC-220 Series 4G LTE Cat 1 Industrial IoT Router
Quick start guide This quick start guide is designed to get you up and running quickly with your new NTC-220 Series Router. More advanced set up instructions can be found in the user guide which can be downloaded from www.netcommwireless.com/ product/ntc-220. Package contents | Industrial IoT The NTC-220 Series package includes: 2 1 x NetComm NTC-220 Series Router 1 x Quick Start Guide 2 x Cellular antennas 1 x 1.
NTC-220 Series 4G LTE Cat 1 Industrial IoT Router Device overview RJ45 Fast Ethernet port Reset button SIM card slot Six-way terminal block connector Micro USB 2.
Item Description Aux antenna socket SMA female connector for auxiliary antenna (receive diversity). Serial port Female DE-9 port supporting 9-wire RS-232, RS-485 or RS-422 (software selectable). GPS antenna socket SMA female connector for GPS antenna. Main antenna socket SMA female connector for main antenna. Press and hold for less than 5 seconds to reboot to normal mode.
NTC-220 Series 4G LTE Cat 1 Industrial IoT Router Getting started Depending on your chosen setup, you may need certain components to configure your device correctly, such as: An external power supply unit for the NTC-220 Series Router (not included). A flathead screwdriver for terminating power input wires. A laptop or PC for advanced configuration. | Industrial IoT Additional fasteners and screwdrivers for specific wall or rail mounting.
Overview of LED indicators LED Icon Name Power Colour State Description Off Power off Double flash Powering up On Power on On Power on in recovery mode Slow flashing Hardware error On Connected via WWAN Blinking Traffic via WWAN Slow flashing Connecting PDP On Registered network Slow flashing Registered network Slow flashing SIM PIN locked Fast flashing SIM PUK locked 1 Network | Industrial IoT On 6 Can’t connect / Device in “Configuration mode”
NTC-220 Series 4G LTE Cat 1 Industrial IoT Router LED Icon Name GPS / Customizable LED Indicator Signal strength Colour State Description Off GPS function disabled On GPS function is enabled but no satellite is detected. Flashing Satellite detected, acquiring location. On Satellite detected, location acquired. On LTE signal On WCDMA signal On GSM signal The term “blinking” means that the LED may pulse, with the intervals that the LED is on and off not being equal.
Installing your device Step 1: Insert the SIM card Before inserting the SIM card, examine it for signs of damage or deformation that could prevent it being safely inserted or allowing it to become stuck in the unit. Examine the gold contact point of the SIM for signs of wear or damage that may prevent it from working correctly. Press the SIM Eject button to eject the SIM card tray. Place the SIM card in the tray and then insert the loaded tray into the SIM card slot with the gold side facing up.
NTC-220 Series 4G LTE Cat 1 Industrial IoT Router Step 3: Mount the router Mount your router in a suitable location using the options listed below. 1. Wall mount Use a minimum of 2 screws (5mm diameter) through the holes on either side of the device. DIN rail mounting bracket 4 x mounting holes allow you to secure the DIN bracket to a wall, using a minimum of 2 screws (3.5mm diameter).
Horizontal DIN rail mounting adapter Used in conjunction with the DIN rail mounting bracket, this adapter lets you mount the NTC-220 in a horizontal orientation. With the DIN rail mounting bracket attached to the router, slide the adapter on to the bracket as shown in the image below. You can then mount the device horizontally on a DIN rail. Optionally, you may place a screw (max. 4.5mm diameter) through the centre hole of the adapter so that it doesn’t move along the DIN rail. | Industrial IoT 2.
NTC-220 Series 4G LTE Cat 1 Industrial IoT Router 4. DIN rail mount 5. Pole mount using DIN rail bracket Use cable ties (max. 5mm width) through holes in the mounting bracket 6. Desk mount The signal strength LEDs update within a few seconds with a rolling average signal strength reading. When selecting a location for the router, please allow up to 20 seconds for the signal strength LEDs to update before repositioning.
Step 4: Connect the power and Ethernet cables Connect power to your router using one of the following options. DC power via the six-way connector Remove the attached green terminal block from your router and connect to the router’s power socket using a DC power supply, sold separately. DC power via field terminated power source If an 8-40V DC power supply is available, you can insert the wires into the supplied terminal block to power your router.
NTC-220 Series 4G LTE Cat 1 Industrial IoT Router Step 5: Access the router’s web interface In your web browser’s address bar, enter https://192.168.1.1/ Note – The HTTP protocol is disabled by default, secure HTTP (HTTPS) is the default protocol. HTTP access is available but must be manually enabled. The web user interface is displayed. There are two system management accounts (Root Manager and Admin) with different management capabilities.
Configure as a new device a) Select “I want to configure this as a new device” then click the OK button. b) In the New Passwords section, enter a strong password in each field. You may configure the same password for all three accounts, but it must meet the security criteria set out below: he password must be a minimum of eight characters and no more than 128 T characters in length. he password must contain at least one upper case, one lower case character T and one number.
NTC-220 Series 4G LTE Cat 1 Industrial IoT Router c) When you have completed all password fields, press the Save button. If the passwords meet the security criteria, they are saved and the router reboots to Live mode automatically. See below for further instructions on logging in. Restore configuration from a previous backup file a) Select “I want to restore my configuration from a previous backup” then click the OK button. c) The router restores the previous configuration and then reboots.
Step 6: Unlock the SIM card If the inserted SIM card is PIN locked, a pop-up window is displayed informing you that you must unlock the SIM before use. Click the OK button. The SIM Security page is displayed. | Industrial IoT In the Current PIN field, enter the SIM PIN and then enter it again in the Confirm current PIN field. If you do not want to enter the PIN code each time the SIM is inserted, select the Remember PIN option. Click the Save button.
NTC-220 Series 4G LTE Cat 1 Industrial IoT Router Step 7: Connect to the Internet If the SIM Status is OK, the NTC-220 Series Router automatically attempts to connect to the Internet by detecting the correct APN and connection details. If automatic configuration was unsuccessful, you must manually enter the connection details. To manually configure the connection profile: 1. 2. 3. From the top menu bar, select the Networking option. Next to Profile1, click the button.
Safety and product care Electrical safety Accessories Only use approved accessories. Do not connect with incompatible products or accessories. Connection to a car Seek professional advice when connecting a device interface to the vehicle electrical system. Distraction Operating machinery Full attention must be given to operating the machinery in order to reduce the risk of an accident. Driving Full attention must be given to driving at all times in order to reduce the risk of an accident.
NTC-220 Series 4G LTE Cat 1 Industrial IoT Router Do not use harsh chemicals, cleaning solvents, or aerosols to clean the device or its accessories. Do not paint your device or its accessories. Do not attempt to disassemble your device or its accessories, only authorised personnel must do so. Do not expose your device or its accessories to extreme temperatures. Ensure that the device is installed in an area where the temperature is within the supported operating temperature range of -30°C to +70°C.
Electrostatic discharge (ESD) Do not touch the SIM card’s metal connectors. Air Bags Do not place the device in the area near or over an air bag or in the air bag deployment area Mount the device safely before driving your vehicle. Emergency & other situations requiring continuous connectivity This device, like any wireless device, operates using radio signals, which cannot guarantee connection in all conditions.
NTC-220 Series 4G LTE Cat 1 Industrial IoT Router The level of interference will depend on the type of hearing device and the distance from the interference source, increasing the separation between them may reduce the interference. You may also consult your hearing aid manufacturer to discuss alternatives. Medical devices Please consult your doctor and the device manufacturer to determine if operation of your device may interfere with the operation of your medical device.
Regulatory compliance FCC Statement (NTC-221, NTC-224) FCC compliance Federal Communications Commission Notice (United States): Before a wireless device model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government-adopted requirement for safe exposure. FCC regulations This device complies with part 15 of the FCC Rules.
NTC-220 Series 4G LTE Cat 1 Industrial IoT Router the power level at which your device transmits. • This device meets the government’s requirements for exposure to radio waves. • This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. • This device complies with FCC radiation exposure limits set forth for an uncontrolled environment.
Frequency (MHz) NANT-00001 NANT-00006 (NTC-221, NTC224) (NTC-221 ONLY) NANT-00001 (NTC-225) Gain (dBi) Gain (dBi) Gain (dBi) LTE Band 2 (1900) 3.42 2.72 - LTE Band 4 (1700) 3.28 2.09 3.28 LTE Band 5 (900) 3.13 0.40 - LTE Band 7 (2600) 3.80 3.17 - LTE Band 13 (700) - - 4.71 Company Contact Details Name: NetComm Wireless Inc. US Address: 1000 Sawgrass Corporate Parkway, Suite 500, Sunrise, Florida 33323, USA Website: https://netcommwireless.
NTC-220 Series 4G LTE Cat 1 Industrial IoT Router (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. RF Exposure Information (MPE): This device has been tested and meets applicable limits for Radio Frequency (RF) exposure. / Cet appareil a été testé et répond aux limites applicables en matière d’exposition aux radiofréquences (RF).
Frequency (MHz) Gain (dBi) LTE Band 4 3.28 LTE Band 12 4.71 CE Regulation RF Exposure Information (MPE) This device meets the EU requirements and the International Commission on NonIonizing Radiation Protection (ICNIRP) on the limitation of exposure of the general public to electromagnetic fields by way of health protection. To comply with the RF exposure requirements, this equipment must be operated in a minimum of 20 cm separation distance to the user.
NTC-220 Series 4G LTE Cat 1 Industrial IoT Router NTC-222 Maximum RF Power Frequency (MHz) Gain (dBi) GSM 900 36.11 DCS 1800 32.57 WCDMA Band 1 25.78 WCDMA Band 8 26.25 LTE Band 1 25.78 LTE Band 3 25.48 LTE Band 7 25.48 LTE Band 8 26.10 LTE Band 20 25.80 WEEE Regulation Waste Electrical and Electronic Equipment (WEEE) This symbol means that according to local laws and regulations your product and/ or its battery shall be disposed of separately from household waste.
Product Warranty For warranty information please visit https://support.netcommwireless.com/warranty-info Technical Support NETCOMM WIRELESS LIMITED ABN 85 002 490 486 Head Office, 18-20 Orion Road Lane Cove, Sydney, NSW 2066, Australia p: e: +61 2 8205 3888 f: +61 2 9424 2010 m2msales@netcommwireless.com www.netcommwireless.com MPRT-00004-000 Rev11 For firmware updates or if you have any technical difficulties with your product, please refer to the support section of our website. https://support.
