Quick Start Guide QSG-00097 rev 7 AIMWLLR0-35 [NRB-0200] QSG.
Welcome | AIMWLLR0-35 This quick start guide is designed to familiarize you with the features and use of the NetComm Wireless Antenna Alignment Tool. The Antenna Alignment Tool is a battery-powered tool which connects to the alignment port on the back of a NetComm Wireless Outdoor Antenna, providing power and a wireless access point.
Antenna Alignment Tool Package contents 1 x AIMWLLR0-35 Antenna Alignment Tool (in pouch) 1 x Antenna Alignment Tool pouch 1 x WiFi security card 1 x Quick Start Guide 1 x Micro USB to Type-A charge cable 1 x AC wall charger (5V/2A) QSG-00097 rev 7 AIMWLLR0-35 [NRB-0200] QSG.
Device overview | AIMWLLR0-35 ITEM DESCRIPTION 1 Connector protective cap Protects the connector from dust and moisture when the Antenna Alignment Tool is not in use. 2 Power button Push once to toggle the Antenna Alignment Tool on and off. When not connected to the antenna and turned on, the Antenna Alignment Tool displays the remaining battery charge level. See the LED indicator section for details on the battery level indication.
Antenna Alignment Tool 3 QSG-00097 rev 7 AIMWLLR0-35 [NRB-0200] QSG.
Charging the Antenna Alignment Tool | AIMWLLR0-35 The included USB cable can be used to charge the Antenna Alignment Tool. Connect the USB cable from the Micro USB port on the Antenna Alignment Tool to the included AC wall charger or another 5V/2A power source for optimum charging speed. The LED indicators on the side of the Antenna Alignment Tool light up and may flash depending on the remaining battery level. See the LED indicator section for details on reading the battery level.
Antenna Alignment Tool Checking the remaining battery level QSG-00097 rev 7 AIMWLLR0-35 [NRB-0200] QSG.indd 7 | AIMWLLR0-35 Press the Power button once. The Antenna Alignment Tool goes into Battery check mode and the LED indicators light up according to the description in the LED indicators section of this guide.
LED Indicators The LED indicators display different things depending on the mode of the Antenna Alignment Tool. a) Battery check mode – When the power button is pressed or the battery is charging. | AIMWLLR0-35 95-100% 80-94% 35-49% 65-79% 20-34% 50-64% 0-19% 8 QSG-00097 rev 7 AIMWLLR0-35 [NRB-0200] QSG.
Antenna Alignment Tool b) Cell scanning mode - When the Antenna Alignment Tool is connected to an Outdoor Antenna. Medium signal QSG-00097 rev 7 AIMWLLR0-35 [NRB-0200] QSG.
c) Normal operation mode – When the Antenna Alignment Tool is connected to an Outdoor Antenna. LED 1 indicates the Ethernet connection status of the antenna. LED 1 DESCRIPTION Link is up Activity on Ethernet LED 2 indicates the Cellular connection status of the antenna. LED 2 STATUS DESCRIPTION Data APN attached Data APN attaching LTE registered LTE registering LTE not registered LED 3 indicates the Power status of the antenna.
Antenna Alignment Tool Using the Antenna Alignment Tool to align an outdoor antenna Before beginning to align an outdoor antenna, press the battery check button on the bottom of the Antenna Alignment Tool and observe the battery level indicated by the LED indicators. Ensure that you have an adequate charge level for the installation. To align an outdoor antenna: 1. Prepare the outdoor antenna as per the Installation Guide. QSG-00097 rev 7 AIMWLLR0-35 [NRB-0200] QSG.indd 11 | AIMWLLR0-35 2.
3. Remove the protective cap from the Antenna Alignment Tool’s connector then connect the Antenna Alignment Tool to the alignment port of the antenna as shown below. | AIMWLLR0-35 4. When the device is positioned at the mounting location, press the Antenna Alignment Tool’s Power button once to turn it on. 12 QSG-00097 rev 7 AIMWLLR0-35 [NRB-0200] QSG.
Antenna Alignment Tool 5. Wait approximately 1 minute for the antenna to go through its boot up process. NOTE: When the Antenna Alignment Tool is connected to the Outdoor Antenna, do not point the front panel of the antenna directly at other people or yourself. Always maintain a separation distance of 8 inches between any part of your body and the front of the antenna (the official FCC recommendation specifies 20cm separation).
RF Exposure The AIMWLLR0-35 contains a transmitter and a receiver. When it is on, it receives and transmits RF energy. When you communicate with your device, the system handling your connection controls the power level at which your device transmits. The AIMWLLR0-35 meets the government’s requirements for exposure to radio waves. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government.
Antenna Alignment Tool FCC Statement FCC compliance Federal Communications Commission Notice (United States): Before a wireless device model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government-adopted requirement for safe exposure. FCC regulations This device complies with part 15 of the FCC Rules.
Product Warranty For warranty information please visit http://www.netcommwireless.com/ Safety and product care Please refer to the user guide for safety and product care information. QSG-00097 rev6 NETCOMM WIRELESS LIMITED ABN 85 002 490 486 Head Office, 18-20 Orion Road Lane Cove, Sydney, NSW 2066, Australia p: e: +61 2 8205 3888 f: sales@netcommwireless.com +61 2 9424 2010 www.netcommwireless.com QSG-00097 rev 7 AIMWLLR0-35 [NRB-0200] QSG.