NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice User Guide 3G10WVR YML10WVR www.netcommlimited.
Preface The purpose of this manual is to provide you with detailed information on the installation, operation and application of your HSPA WiFi Router with Voice. Important Notice and Safety Precaution Before servicing or disassembling this equipment, always disconnect all power or telephone lines from the device. Use an appropriate power supply, preferably the supplied power adapter, with an output of DC 12V 1.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice Table of Contents Preface ................................................................................................................................................................................................... 2 Introduction ........................................................................................................................................................................................... 5 1.1 Features ..................
Introduction
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice Introduction With the increasing popularity of the 3G standard worldwide, this HSPA WiFi Router with Voice provides you with triple-band coverage through expanding cellular networks throughout the world. By following the simple step-by-step instructions found on the Connection Manager USB key, you can share your connection with multiple wireless and wired devices using the 3G network.
1.3 LED Indicators The front panel LED indicators are shown in this illustration and followed by detailed explanations in the table below.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice 1.4 Rear Panel The rear panel contains the ports for data and power connections. Main 3G Antenna (removable, SMA connection) Power jack for DC power input (12VDC / 1.5A) Power button USIM card slot Aux 3G Antenna (removable, SMA connection) USB Port (For connecting a USB Printer or USB Storage Device) Reset button 2 Phone Port (for Circuit-Switched Voice Call) 2 RJ-45 Ethernet Ports YML10WVR www.netcommlimited.
Quick Setup
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice Quick Setup 2.1 Setup Procedure These steps explain how to quickly setup your 3G Router: 1. Attach the two 3G antennas provided to the ports marked Main and AUX on the back of the router. The antennas should be screwed in a clockwise direction. 2. Insert your SIM card (until you hear a click) into the USIM slot at the back of the Router. 3. Connect the yellow networking cable to one of the yellow ports found at the back of the Router. 4.
Web User Interface
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice Web User Interface This section describes how to access the device via the web user interface using a web browser such as Microsoft Internet Explorer (version 6.0 or later). 3.1 Default Settings The following are the default settings for the device. Local (LAN) access (username: admin, password: admin) Remote (WAN) access (username: support, password: support) User access (username: user, password: user) LAN IP address: 192.168.1.
STATIC IP Mode $ ; # ! ; $ # ! + +'? + 8 1. From the Network Connections window, open Local Area Connection (You may also access this screen by double-clicking the Local Area Connection icon on your taskbar). Click the Properties button. 2. Select Internet Protocol (TCP/IP) and click the Properties button.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice MAC OSX 10.4 DHCP Mode To set your Apple Mac for DHCP mode, browse to the Apple menu and select System Preferences. In the System Preferences menu, ^ " ^ " { J# # $ \ ^ \ ) ! \ * STATIC Mode ! ! \ $ ;
3.3 Login Procedure To login to the web interface, follow the steps below: NOTE: The default settings can be found in 3.1 Default Settings. 1. NOTE: ! ; 8 $ ! |]]+ +'? + + For local administration (i.e. LAN access), the PC running the browser must be attached to the Ethernet, and not necessarily to the device.
3G Settings
3G Settings 4.1 3G Service Setup ( &* your assistance. 4.1.1 $ $ ( 3G Settings &* ( !" # $ NOTE: Sections 8.3 and 8.4.2 also provide information about the 3G service. ( $ username and password.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice !" # $ This screen allows for changes to the 3G SIM card PIN code protection settings. NOTE: If you have entered the incorrect PIN 3 times, your SIM card will be locked for your security. Please call your 3G Provider for assistance. 4.2.1 PIN Code Protection PIN code protection prevents the use of a SIM card by unauthorized persons. To use the 3G internet service with this router however, the PIN code protection must be disabled.
4.2.2 PIN Code Change If you wish to change your PIN code for greater security, enable the PIN Code protection. Go to the previous section and follow the procedure listed under PIN Lock On. \ ^ (!) !" # # " !" $ & (!) ^ # &* Carrier if you require assistance.
Wireless
Wireless 8 8 } \ " ^ K}\"Q $ | Wireless network name Channel restrictions (based on country) Security Access point or bridging behaviour Station information 5.1 Setup $ }\" }\" hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice 5.2 Security This Router includes a number of security options that provides you with a secure connection to a 3G network. State-of-the art security includes: WEP / WPA / WPA2 data encryption SPI Firewall VPN Pass-Through )\# ! $ Authentication protocols – PAP / CHAP You can authenticate or encrypt your service on the Wired Equivalent Privacy (WEP) algorithm, which provides protection against unauthorized access such as eavesd
The settings for WPA authentication are shown below. OPTION DESCRIPTION WE P Encryption This option indicates whether data sent over the network is encrypted. The same network key is used for data encryption and network authentication. Whilst four network keys can be defined, only one can be used at any one time. Use the network key found in the drop down list. E ncryption S trength This drop-down list box will display when WEP Encryption is enabled.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice % & # $ # $ Wireless Local Area Network (WLAN) interface: Select the channel which you wish to operate from Force the transmission rate to a particular speed Set the fragmentation threshold Set the RTS threshold Set the wake-up interval for clients in power-save mode Set the beacon interval for the access poin
OPTION DESCRIPTION 54g Mode S elect A uto mode for greatest compatibility. Select Performance mode for the fastest performance among 54g certified equipment. Select LRS mode if you are experiencing difficulty with legacy 802. 11b equipment. If this does not work, you may also try 802.11b only mode. 54g Prote c tion In A uto mode, the router will use R TS/C TS to improve 802.11g performance in mixed 802.11g/802.11b networks. Tur ning protection Off will maximize 802.11g throughput under most conditions.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice 5.5 Wireless Bridge 8 features of the wireless LAN interface. $ # ^ ( ]\ $ FEATURE DESCRIPTION AP Mode S electing W ireless Bridge (W ireless Distribution System) disables Access Point (AP functionality while selecting Access Point enables AP functionality.
Management
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice Management The Management menu has the following maintenance functions and processes: 6.1 Device Settings 6.2 Simple Network Management Protocol (SNMP) 6.3 Simple Network Time Protocol (SNTP) 6.4 Access Control 6.5 Save and Reboot 6.1 Device Settings The Device Settings screens allow you to backup, retrieve and restore the default settings of your Router. It also provides a function for ; $ 6.1.
6.1.3 Restore Default The following screen appears when selecting Restore Default. By clicking on the Restore Default Settings button, you can restore your ; $ ; NOTE: The default settings can be found in section 3.1 Default Settings. Once you have selected the Restore Default Settings button, the following screen will appear.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice ' # $ (") &*+-8:; The Simple Network Management Protocol (SNMP) allows a network administrator to monitor a network by retrieving settings on remote network devices. To do this, the administrator typically runs an SNMP management station program such as MIB browser on a local host to obtain information from the (") &*+-8:; K (") Q \ (") \
6.3 Simple Network Time Protocol (SNTP) $ as illustrated below. ; ! ^ The following options should now appear (see screenshot below): # $ NOTE: First NTP timeserver: Select the required server. Second NTP timeserver: Select second timeserver, if required. Time zone offset: Select the local time zone. ^ ( ]\ SNTP must be activate
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice 6.4.1 Services The Service Control List (SCL) allows you to enable or disable your Local Area Network (LAN) or Wireless Area Network (WAN) services by ticking the checkbox as illustrated below. These access services are available: FTP, HTTP, ICMP, SSH, TELNET, and TFTP. Click Save/Apply to continue. 6.4.2 IP Address The IP Address option limits local access by IP address.
6.4.3 Passwords $ ; \ user accounts: admin is to be used for local unrestricted access control support is to be used for remote maintenance of the device { $ spaces. Click Save/Apply to continue. $ +' 6.
Advanced Setup
Advanced Setup This chapter explains advanced setup for your Router: 7.1 Local Area Network (LAN) $ } \ HSPA WiFi Router with Voice User Guide 34 " ^ K}\"Q ; YML10WVR www.netcommlimited.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice ( $ OPTION DESCRIPTION I P Addre ss Enter the IP address for the LAN interface S ubne t Ma sk Enter the subnet mask for the LAN interface Ena ble UPnP T ick the box to enable Universal Plug and Play Ena ble Ha lf-B r idge The Router can be set up as a half- transparent bridge to cope with some special applications such as VPN pass-through. By default half- bridge is o ff.
7.2 Network Address Translation (NAT) 7.2.1 Port Forwarding $ ! K $ Q with a private IP address on the LAN side. The Internal port is required only if the external port needs to be converted to a different port }\" \ & $ To add a Virtual Server, click the Add button. The following screen will display.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice 7.2.2 Port Triggering ( $ ; $ $ }\" # ]{ ; 8\" ^ }\" \ & $ To a
7.3 Security Your Router can be secured with IP Filtering or Parental Control functions. 7.3.1 IP Filtering ! $ ! $ ) $ \ $ ! ^ $ Outgoing IP Filter $ \## { BLOCKED. $ ^ \ ! ^ THE FILTER RULE
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice $ ^ \ ! $ # ^ ( ]\ 7.3.2 $ Parental Control This Parental Control allows you to restrict access from a Local Area Network (LAN) to an outside network through the Router on selected days at certain times.
7.4 Routing Default Gateway, Static Route and Dynamic Route settings can be found in the Routing link as illustrated below. 7.4.1 Default Gateway If the Enable Automatic Assigned Default Gateway checkbox is selected, this device will accept a default Gateway assignment. If the ^ $ ] 8\" ^ Save/Apply.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice 7.4.3 Dynamic Route To activate this option, select the Enabled radio button for Global RIP Mode. $ ;! # ^ ( ]\ $ ^ ^ 7.5 Domain Name Servers (DNS) ! \ \ "( ^
Voice
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice Voice The 3G10WVR Router with Voice allows you to make telephone calls over the 3G Mobile/Cellular Telephone network using a standard Analogue Telephone via the built in RJ-11 Phone port. Please refer to the documentation provided by the manufacturer for operating your Analogue Telephone. " | Note: That any telephone calls placed using the 3G10WVR may incur call usage charges determined by your Network Provider.
Status
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice Status The Status menu has the following submenus: Diagnostics System Log 3G network Statistics Route ARP DHCP PING 8.1 Diagnostics The Diagnostics menu provides feedback on the connection status of the device. The individual tests are listed below. If a test displays a fail status: 1. Click on the Help link 2. " ^ ; $ 3.
8.2 System Log $ System Log. 1. # ^ # $ ( } 2. Select the system log options (see table below) and click Save/Apply. OPTION DESCRIPTION Log Indicates whether the system is currently recording events. You can enable or disable event logging. By default, it is disabled.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice 3. Click View System Log. The results are displayed as follows. YML10WVR www.netcommlimited.
8.3 3G Status Select this option for detailed status information on your Routers 3G connection. # $ STATUS DESCRIPTION Ma nufa c turer The manufacturer of the embedded 3G module. Mode l The model name of the embedded 3G module FW R e v The firmware version of the 3G module. IME I The IMEI (Inter national Mobile Equipment Identity) is a 15 digit number that is used to identify a mobile device on a network.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice OPTION DESCRIPTION Signa l Le vel (RS S I) 3G Radio Signal Strength Index Q ua lity ( Ec/Io) strongest cells. K ]! Q Ne tw or k Registration S tatus S hould display as registered with a valid unlocked SIM card. Ne tw or k N ame The 3G inter net Service Provider. Countr y & Network Codes Each country and network has a unique code. Ce ll ID The network information for the “serving” cell ID.
8.4 Statistics These screens provide detailed information for: Local Area Network (LAN) and Wireless Local Area Network (WLAN) 3G Interfaces NOTE: These statistics page refresh every 15 seconds. 8.4.1 LAN Statistics This screen displays statistics for the Ethernet and Wireless LAN interfaces. 8.4.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice 8.5 Route Select Route to display the paths the Router has found.
? @ J # $ K J# Q Click DHCP to display the DHCP information. FIELD DESCRIPTION Hostname Shows the device/host/PC network name MAC Address Shows the Ether net MAC address of the device/host/PC IP address Shows IP address of device/host/PC Expires In Shows how much time is left for each DH C P Lease 8.8 PING The PING menu provides feedback of connection test to an IP address or a host name. Input an IP address or a host name, e.g www.google.com and press Submit.
Appendices
Appendix A: Print Server For Windows Vista/7 These steps explain the procedure for enabling the Printer Server for Windows Vista or Windows 7. 1. Enable Print Server from Web User Interface. Select Enable on-board print server checkbox and enter Printer name and Make and model NOTE: The Printer name can be any text string up to 40 characters. The Make and model can be any text string up to 128 characters. 2.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice 3. ( \ ^ 4. # ^ # ^ " ( |]]+ +'? + +|'&+] ] NOTE: The PrinterName must be the same as the printer name entered into the Printer section of 3G10WVR. 5. " have your printer driver installation media. YML10WVR www.netcommlimited.
6. # 7. # ^ $ HSPA WiFi Router with Voice User Guide 56 ^ " YML10WVR www.netcommlimited.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice For MAC OSX These steps explain the procedure for enabling the Printer Server on Mac OSX. Enable Print Server from Web User Interface. Select Enable on-board print server checkbox and enter Printer name and Make and model NOTE: The Printer name can be any text string up to 40 characters. The Make and model can be any text string up to 128 characters. To set up your printer, check the Apple menu, select System Preferences.
! \ $ + +'? + +|'&+ ] ] " NOTE: The PrinterName must be the same as the printer name entered into the Printer section of 3G10WVR. From Print Using drop down list and select your corresponding printer driver. Click Add and check the printer status. HSPA WiFi Router with Voice User Guide 58 YML10WVR www.netcommlimited.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice Appendix B: Samba Server For Windows Vista/7 Open a web-browser (such as internet Explorer, Firefox or Safari) Type in the address \\ “NetbiosName”\ “DirectoryName” \ (eg \\ntc-cpe\ntc-cpe) " | {( ] ]$ {( For MAC OSX # ^ $ ^ Choose Connect to Server from the Go menu.
Legal & Regulatory Information This manual is copyright. Apart from any fair dealing for the purposes of private study, research, criticism or review, as permitted under the Copyright Act, no part may be reproduced, stored in a retrieval system or transmitted in any form, by any means, be it electronic, mechanical, recording or otherwise, without the prior written permission of NetComm Limited. NetComm Limited accepts no liability or responsibility, for consequences arising from the use of this product.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice Federal Communication Commission Interference Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IC Important Note IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. The County Code Selection feature is disabled for products marketed in the US/Canada.
NETCOMM LIBERTY SERIES - HSPA WiFi Router with Voice NETCOMM LIMITED J $ PO Box 1200, Lane Cove NSW 2066 Australia W: www.netcommlimited.com ^ YML10WVR www.netcommlimited.
