Installation Instructions

ManualsBrandsNEO ManualsElectronicsWater Valve

Wi-Fi Water Valve Manual

FCC STATEMENT :

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two co

nditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may

cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compli

ance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pr

otection against harmful interference in a residential installation. This equipment generates us

es and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no gu

arantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

Reorient or relocate the receiving antenna.

Summary of content (15 pages)

PAGE 1
Wi-Fi Water Valve Manual FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two co nditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compli ance could void the user's authority to operate the equipment.
PAGE 2
Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled envir onment. This equipment should be installed and operated with minimum distance 20cm betw een the radiator & your body.
PAGE 3
Water valve upper shell silicone loop PCBA upper Lower PCBA Deceleration motor module Water valve middle shell water joint Water pressure sensor DN20 copper pipe assembly Water valve lower shell rubber plug
PAGE 4
2.Appearance description DN20,3/4INCH Power interface DC5V / 2A WATER OUT WATER IN RESET BUTTON (blue) Water ON/OFF (ON: blue; :OFF:red) 3.
PAGE 5
⑤Waterproof silicone pad*2 ⑥ threaded protection cover (pre-install in factory) ⑥Power Adapter (5V / 2A) 4.Installation method (1) Water pipe installation Prepare tools spanner 1.Wrap the water pipe connector with waterproof tape tape hexagon bar 2.
PAGE 6
3.Tighten the water pipe connector with the inner hex 5.Put the silicone pad into the water pipe connectort, and then dock the 4.wrap water valve copper pipe with waterproof tape 6.Tighten the adapter nuts with the wrench water valve copper pipe 7.Single-sided installation completed 8.
PAGE 7
3 Turn on the power supply, installation finished . 1.Check the power supply interface slot 2. Align at the interface and press firmly 3. Turn the nut clockwise 5. Notes: (1) The minimum water temperature detection temperature is-10℃.
PAGE 8
The indicator light corresponds to the device status device status Indicator status Bluetooth mode / Smart Wi-Fi / AP compatible mode The indicator light flashes once every 2 seconds Water valve switch status Water valve switch indicator light is flashing (green:on / red: off) reset Press the reset button for 6s, the reset button indicator will flash slowly (device is waiting for configuration) Tip: The device can be powered by the power bank .
PAGE 9
2. Add device via Bluetooth (this method is recommended) (1) Method 1: Active Bluetooth in Mobile phone to add the device through Bluetooth mode (the standby mode can be added with Bluetooth) (2) Method 2 (After activating Bluetooth, enter the APP interface, the device will be automatically searched by Bluetooth, and then click Add) 3.
PAGE 10
4. Add device via AP compatible mode Press the reset button until the device flashes slowly (pending distribution mode), and then add (follow the APP prompts) Main functions, working status and record Settings 1.
PAGE 11
2. Water quantity record; (you can see the water usage in day, month and year) 3. Water leakage self-inspection; (One key to check the leakage ,if detected the leakage ,it will be reported immediately ) 4.
PAGE 12
（3）Alarm record (water temperature, pressure, water consumption and water leakage alarm) 5.
PAGE 13
(3) Flow unit setting ("gal / h" and "m³ / h") Other functions 1.
PAGE 14
2. Product linkage 3. Push notification management APP push notification:Turn off the switch, all devices in APP can not receive the push notification, but all alarm messages still can be checked in the message center; 4.
PAGE 15
. Make Your Home Smarter