User's Manual

ManualsBrandsNEO ManualsElectrical EquipmentSmart Plug

Repeater User Manual

(S2 Version)

Thank you for your support

⚫ Please read the instruction manual carefully before operating

⚫ Please keep the instruction manual for further reference

This product can be included and operated in any Z-Wave™ network with other Z-Wave™ certified

devices from other manufacturers and/or other applications. All non-battery operated nodes within

the network will act as repeaters regardless of vendor to increase reliability of the network.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

Summary of content (9 pages)

PAGE 1
Repeater User Manual (S2 Version) Thank you for your support ⚫ Please read the instruction manual carefully before operating ⚫ Please keep the instruction manual for further reference This product can be included and operated in any Z-Wave™ network with other Z-Wave™ certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
PAGE 2
and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
PAGE 3
Blue led will blink with 1、 Power up the device. 1s interval until 2 、 Set Z-Wave™ Controller into exclusion exclusion successful. mode Remove 3 、 Press and hold the button for 5s until Green led lights is on, then release the button before green led turn off. 1、 Power up the device. 2、 Press and hold the button for 10s until Red Factory Reset² led lights is on, then release the button before red led turn off. 1、 Press and hold the button.
PAGE 4
command. When ambient humidity value is less than the setting value in “Configuration: No.9”, device will trigger a low humidity alarm and send a BASIC_SET = 0xFF to the nodes that associated in group 5. And BASIC_SET = 0x00 will be sent when humidity value is large than the setting value in “Configuration: No.9”.
PAGE 5
”), the device will unsolicited to send a “SENSOR_MULTILEVEL_REPORT” to nodes which associated in lifeline. Command Class COMMAND_CLASS_SENSOR_MULTILEVEL Command SENSOR_MULTILEVEL_REPORT Type Humidity Scale 0.
PAGE 6
The D- Value = [Value] × 0.1 RH%. Parameter Number Size (Byte) 6 1 Available Settings 0 ~ 100 Default value (min) 20 7) Low Temperature Alarm Value This parameter is configured the threshold value that alarm level for low temperature. When the current ambient temperature value is less than this configuration value, device will trigger an alarm through the device associated in group 2. The Alarm Value = [Value] × 0.1 Degree Celsius / Fahrenheit (US).
PAGE 7
Command Class Basic This device support COMMAND_CLASS_BASIC to control other devices associated in group 2, 3, 4, 5. The devices associated in group 2, 3 , 4, 5 must be the AOS device or FLiRS Device. The BASIC_SET value can refer to “Association Group 2, 3, 4, 5” SmartStart SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the product with a controller providing SmartStart inclusion.
PAGE 8
Security Levels SECURITY_KEY_S0 SECURITY_KEY_S2_UNAUTHENTICATED SECURITY_KEY_S2_AUTHENTICATED SECURITY_KEY_S2_ACCESS Support (Yes/No) Yes Yes Yes No All Supports Command Class in Each NIF Lists Command Class Version Not Non-secure Included Included S0 Included Non-Secure Secure S2 Included Non-Secure Secure 2 ● ● ● ● COMMAND_CLASS_SECURITY 1 ● ● ● ● COMMAND_CLASS_SECURITY_2 1 ● ● ● ● COMMAND_CLASS_TRANSPORT_SERVICE 2 ● ● ● ● COMMAND_CLASS_VERSION 3 ● ● ● ● COMMAND_CL
PAGE 9