Instruction Manual PIR Motion Sensor Thank you for your support Please read the instruction manual carefully before operating Please keep the instruction manual for future reference Shenzhen Neo Electronics Co.
Product Introduction The PIR is a passive infrared detector or body sensor with a temperature probe, the sensor doesn’t emit any energy but only passively receive and detect infrared radiation from outside. Under room temperature, all items have radiation. Human beings are warm-blooded animal with stable infrared radiation, are most easily to be detected. That’s why we also call it body sensor. PIR send messages via Z-wave network to the Z-wave main controller.
Brief introduction of function 1. motion detection function 2. illumination value detection function 3. function of temperature detection 4. power saving function Data reporting rule Illumination reporting rule: 1. after power on, there will be a report data; 2., when the illumination change value is more than 100 lux (set), then update data is reported; Temperature reporting rule: 1. after power on, there will be a data report, 2., when the temperature changes more than 0.
Product List PIR Holder Battery Screw Screw stopper Sticker Instruction manual 1pc 1pc 1pc 2pcs 2pcs 1pc 1pc
Including Sensor (PIR) to Z-wave Network The PIR can be included to the Z-wave network by pressing on the code button. 1) Disassemble the PIR main body and insert the battery into the contact sensor. Make sure the device is located within the direct range of the controller. 2) Set the controller into the learning mode (see mail controller’s operating manual). 3) Quickly, triple click the code button, LED light will flash red for 5 times. 4) PIT will be detected and included in the Z-wave network.
Battery Installation Open the PIR Install the battery Close the PIR Fix PIR on the Holder Detection Range and Working Conditions PIR has to be installed in a corner of the room or perpendicularly to the doors. Actual detection range of the sensor can be influenced by environment conditions. If there are false alarms be reported, check for any moving objects within the sensor’s detection area, such as trees blowing in the wind, cars passing by, windmills.
Detection range of PIR shown in the following picture Working Condition If there is someone moving within the detection area, alarm triggered, and LED lights flash in the inductive area at the same time.
Tips Make sure the PIR is within the Z-wave network. PIR is recommended to be fixed at the height of 2- 4 meters off the ground. When install PIR, please keep it far away from the place where the air temperature changed sensitively, e.g., the neighborhood of air conditioners, refrigerators, stoves and so on. Furniture, large bonsai or other spacers shouldn’t be placed within the PIR’s detection area.
Main controller does not take part in such communication. Using this mechanism, PIR may communicate with other devices even when the main controller is damaged. The Status of LED 1. 2. 3. When the PIR is triggered, LED light flashes red for 1 times. When the PIR installs battery, LED light will flash red for 5 times. Quickly, triple click the code button ,add the PIR to the Z-wave network or delete PIR from Z-wave network , LED light flashes red for 5 times. 4.
NOTE When the PIR is being restored factory settings, please make sure power source is connected. Battery Usage Tips Battery life of the contact sensor is approximately 1 years at factory default settings. The current battery level is displayed in the gateway. Red battery icon means the battery needs replaced. In order to avoid tamper detection, while replacing the battery, please disconnect the association of the contact sensor with other devices. Note Contact sensor is battery powered.
Parameter Number: 2 Parameter Size: 2Byte Available Settings: 5 ~ 600(second) Default Setting: 30 3. Basic Set Level Basic Set Command will be sent where contains a value when PIR detector is triggered, the receiver will take it for consideration; for instance, if a lamp module is received the Basic Set Command of which value is decisive as to how bright of dim level of lamp module shall be. This Parameter is used to some associated devices.
default value. Function: Re‐trigger Interval Setting. Parameter Number: 6 Parameter Size: 1 Byte Available Settings: 1 ~ 8(s) Default Setting: 8 7. Light Sensor Polling Interval This Parameter can be set the light sensor measure ambient illumination level interval time. NOTE: This Value Must Be less than Wakeup Interval Time. Function: Light Sensor Polling Interval Parameter Number: 7 Parameter Size: 2 Byte Available Settings: 60 ~ 36000(second) Default Setting: 180(s) 8.
Differential Value = [Value] × 0.1℃ Function: Temperature Report Parameter Number: 10 Parameter Size: 1 Byte Available Settings: 0 ~ 127 Default Setting: 5 11. Led Blink Enable This parameter defines the Led on/off enable. If this parameter is set to ‘1’, the led blink will be enabled, the led will blink once when motion sensor detect a movement. Otherwise, the led will be turned off always.
k = 0.11538 * 1000 = 115.38 ≈ 115 The parameter should be set to 115.
Guarantee 1. The Guarantee is provided by Shenzhen NEO Electronics Co., Ltd (hereinafter “Manufacture” ) 2. The Manufacturer is responsible for equipment malfunction resulting from physical defects (manufacturing or material) of the device for 12 months from the date of its purchasing. 3. During the Guarantee period, the Manufacturer shall remove any defects, free of charge, by repairing or replacing. 4. In special cases, when the device cannot be replaced with the device of the same type (e.g.
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.