Instruction Manual

ManualsBrandsNeo-Neon Development ManualsElectronics6FT RGB CONE TREE

The Instruction Manual for 6' RGB Cone Tree

Model No.: FCB-VI-OX0125L-6FT-12P

Input Voltage: 120V~60Hz 1.5A Max.

Output: 12V 6.0A

CAUTION:

Use only UL Listed Class2 12V DC Power Supply.

This seasonal product is not intended for permanent installaon.

To reduce the risk of ﬁre or electric shock, do not aempt to replace lamps or modify string.

Always unplug this product before installing.

To reduce the risk of ﬁre and electric shock: Do not install on trees having needles, leaves or branch

coverings of metal ormaterials which look like metal.

To reduce the risk of ﬁre and electrical shock: Do not mount or support strings in a manner that can cut or

damage wireinsulaon.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical products, basic precauons should always be pracced including the following:

1.Please read this manual before use;

2.When the temperature is below ≤ 50°F (10°C), please do not directly straighten the lamp body because the

lamp body is hard,so as not to damage the lamp body. It is recommended to connect the power supply to

light the lamp body for 8~10 minutes.When the lamp body is so, Can be straightened and assembled.

3.In order to reduce the deformaon of the lamp body, it is recommended to vercally pull down the straight

lamp bodyduring assembly. Do not forcibly straighten the lamp body when the lamp body is twisted.

4.The lamp beads are not replaceable;

5.The external wires of the product cannot be replaced. If the external wires are damaged, do not use them.

6.Do not connect with other products;

7.Products can be used indoors and outdoors;

8.Do not place the product near gas, electric heaters, ﬁreplaces, candlescks, or other similar sources of heat;

9.The products are electronic products, non-toy products, please do not play for children, please keep them

out of reach ofchildren, so as not to cause ﬁre, burns, personal injury, electric shock and so on;

10. Avoid piercing the lamp body with sharp objects;

11.Aer the product is installed, do not hang other objects on the product;

12.Do not cover ﬂammable materials when using the product;

13.Please check the integrity of the product before use or before using it. If the product is damaged, please do

not use it. If it isdamaged, please do not use it.

14.The product must be connected to the correct voltage;

15.When a fault occurs, please turn oﬀ the power immediately. Hold the plug when the power is oﬀ, and do

not pull the powercord;

16.If the operaon is not carried out in accordance with the precauons, the manufacturer will not be

responsible.

Page 1 / 3

Summary of content (4 pages)

PAGE 1
The Instruction Manual for 6' RGB Cone Tree Model No.: FCB-VI-OX0125L-6FT-12P Input Voltage: 120V~60Hz 1.5A Max. Output: 12V 6.0A CAUTION: Use only UL Listed Class2 12V DC Power Supply. This seasonal product is not intended for permanent installation. To reduce the risk of ﬁre or electric shock, do not attempt to replace lamps or modify string. Always unplug this product before installing.
PAGE 2
Remote Control User Manual 1. Pull out the plastic ﬁlm from the batter cover to energize the remote. (Fig.1) 2. Point remote to the tree controller box to function. Battery Caution: 1. Always purchase the correct size and grade of battery most suitable for the intended use. 2. Replace only with lithium, type CR2032 battery 3. Clean the battery contacts and also those of the device prior to battery installation. 4. Ensure the battery is installed correctly with regards to polarity (+ and -) 5.
PAGE 3
Product Installation: Step 1: Open the base frame, and insert guide post of the base frame into the hole on the outer ring, and ﬁx the base with screws; (Figure 1 and Figure 2) Step 2: Insert the 3-sections center supporting tube into the hole at base frame; (Figure 3) Step 3: Insert the Star into the iron frame hole at the top of the lamp body; (Figure 3) Step 4: Insert the iron frame of lamp body into the center supporting tube; (Fig.
PAGE 4
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.