Use Instructions

Studio Flash Trigger
RT Series
Instruction Manual
Body
Foreword
Thank you for purchasing RT Series Studio Flash Trigger. It is a
control discreteness for camera to trigger studio flashlight
synchronously. The device is composed of two parts, namely
signal transmitter and receiver.
Contents
Foreword
For Your Safety
Names of Parts
Body
Accessories
Battery
Channel Settings
Instructions for Use
Function Introduction
Connection
Operation
Technical Data
Attentions
Maintenance
For Your Safety
To prevent damage to the product or injury to you or to others,
read the following safety precautions in their entirety before
using this equipment. Keep these safety instructions where
users can read them for ready reference.
Do not disassemble or modify
Failure to observe this precaution could result in electric
shock or product malfunction. Should the product break
open as the result of a fall or other accident, remove the
batteries and take the product to authorized maintenance
center for inspection.
Keep dry
Do not handle with wet hands or immerse in or expose
to water or rain. Failure to observe this precaution could
result in fire or electric shock.
Keep out of the reach of children
This device contains small parts that may pose a
choking hazard. Consult a physician immediately if a
child swallows any part of this device.
Do not expose to high temperature
Do not leave the device in a closed vehicle under the
sun or in other areas subject to extremely high
temperature. Failure to observe this precaution could
result in fire or damage to the casing or internal parts.
Names of Parts
(1) Trigger Output Plug
(2) Receiving Indicator Lamp
(3) Power Switch
(4) Channel Code Switch
(subject to different model,
unavailable for AT-01 )
Receiver
(5) Test Button
(6) Channel Code Switch
(subject to different model,
unavailable for AT-01 )
(7) Camera Hot Shoe
(8) Sync Cord Jack
(9) Transmitter Indicator Lamp
Transmitter
Accessories
1. Convert Adapter
2. Instruction Manual
Transmitter: Slide the battery-chamber cover from the back
of the transmitter and insert one 12V/23A battery (provided
by manufacturer)
Receiver: Slide the battery-chamber cover from the back of
the receiver and insert two AAA 1.5V alkaline batteries
(available separately).
Batteries and Installation
Low Battery Indicator
LED indicator on receiver will blink fast when the batteries
are low. Please change batteries before they run down in
case of flash failure or flash missing.
Replacing Batteries
When replacing batteries on transmitter or receiver
1. Turn the camera off and disconnect the receiver
2. Remove the batteries with new ones
When the device is not in use
1. The transmitter consumes little power and can last over
three years when it is in spare without any operation.
2. The receiver is equipped with a power on/off switch.
To reduce the drain on the batteries when the device is not
in use, please slide the power to OFF position.
Channel Settings
There are16 channels in this device. Set the transmitter and
receiver on the same channel before use. Check the table
for channel setting as below:
1 2 3 4 5 6 7 8 9 10
0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1
0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
11 12 13 14 15 16
S1
S2
S3
S4
channel
RT Series Studio Flash Trigger is based on a wireless remote
system. The transmitter enjoys an advanced electric circuit
which is designed with sleepy function, so it has very low
power consumption. The receiver is used with alternating
current, and it achieves quick response under the advanced
MCU control. It can meet the need of sync flash for any
different shutter camera.
Instructions for Use
Function Introduction
Connection
1.Insert the trig output plug (1)
of the receiver into the synch
control socket of the strobe.
2.Turn on the power switch (3)
of the receiver.
Operation
1.Adjust the same state for the
channel code switch (4) (6) for
the transmitter and receiver.
2.Press the test button (5), and
the transmitter indicator lamp
(9) and the receiving indicator
lamp (2) will turn red.
Simultaneously the strobe will
flash to work.
3.Attach the transmitter onto
the camera hot shoe mount
and press the camera shutter
for instant using(corresponding
function setting is required
for camera).
4.If the camera has no Hot Shoe
Jack, insert one end of the
synchronous line into the
Socket for Synchronous Line
(8) and the other end into the
Synchronous jack of the camera.
Technical Data
RT-01 RT-02 RT-04 RT-16
1 2 4 16
433MHz wireless remote system
12V 23A lithium-ion battery
3V (AAA*2)
Φ6.35mm / Φ3.5mm
≤30 m (Open space)
≤20 m (Open space)
1/200 sec
60*42*30mm
77*33*22mm
Model
Channel
Transmit frequency
Transmitter power
Receiver power
Sync socket
Outdoor operation distance
Indoor operation distance
Sync speed
Transmitter Dimension
Receiver Dimension
Attentions
Unable to trigger flash or camera shutter. Make sure the
transmitter and receiver are set to the same channel,
and the PC cord or the hot shoe mount is completely
connected.
Maintenance
Avoid falling
The device may malfunction after strong shocks or under
excess stress.
Signal disturbance or shooting interference. Change
different channel on the device.
Operating distance limited or flash missing. Check if the
battery is exhausted. Try to change the battery.
Keep away from strong magnetic field. The strong static
or magnetic field produced by devices such as radio
transmitter leads to malfunction.
Avoid sudden temperature changes
such as the circumstance when taking the remote control
out of a building with higher temperature to outside in
winter. This may lead to condensation of moisture.
Please put the remote control in handbag or plastic
bag to prevent sudden temperature changes.
Keep dry
The production isn't water-proof. It will lead to malfunction
if soaked in water or exposed in high humidity, which
cause malfunction and rust, corrosion.
705-RT0000-00
Made In China
GODOX设计文件图注
展开尺寸(mm)
成品尺寸(mm)
尺寸公差
材质
工艺说明
备注/色值
设计师
校对
项目类型
彩盒
贴纸
说明书
内托
胶盒
吸塑
白盒
其他:
彩卡
项目名称
GODOX_RT系列 中性说明书
产品料号
705-RT0000-00
版本
390x120mm
±2mm
128g铜板纸
陈柱 杨入人
红色为刀线，蓝色为压线
98
3
2
1
4
57
6