User Manual

ManualsBrandsNederlandsche Apparatenfabriek NEDAP ManualsElectronicsInductive Proximity Card Reader

Date : 08 April 2013 Version 6

This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no licence under any patent or other right,

nor does the publisher assume liability for any consequence of its use; specifications and availability of goods mentioned in it are subject to change without notice; it is

not to be reproduced in any way, in whole or in part, without the written consent of the publisher.

Page 1 of 4

Part.no.:

5281121

Invexs 190 readers

Mifare DESfire dual technology mullion readers

GENERAL

The Invexs 190 reader series is capable of reading (simultaneously) Mifare

and DESFire credentials due to its dual reader technology. The Invexs 190

is designed to be used on door pillars (mullion) and suitable for outside and

inside use. A model with keypad is also available.

The Invexs output must be set to RS485 protocol (encrypted).

Functionality and output are determined by the configuration of the Invexs

reader. The configuration is defined using the programm AEreco, and

deployed by the configuration card or via AEmon.

Three LEDs (red, green, blue) and beeper are included. LEDs around the

keypad ciphers light up only in case a PIN code is requested.

The pigtail cable can be lead directly backwards or when using the

additional spacer (art. nr . 9949887) to the top or bottom.

DIMENSIONS

MOUNTING PROCEDURE INVEXS

For mounting the Invexs 190, the mounting plate must be placed on the wall

first.

For removing the mounting plate from the Invexs 190, unscrew the screw

(1) (Torx, M5) at the bottom of the Invexs and push the Invexs 190 slightly

up (2). The plate can be mounted using the 4 holes

Place the cable to the correct position and replace the Invexs 190.

Install M

anual

Dimensions: 7.52 x 2 x 1.2 in.

4 mounting holes available at 1.26 x 6.1in

Cable pigtail: 10 x 26AWG shielded, 10 ft

Optional spacer (max thickness 0.4 in) is

available for other cable outlet (top or

bottom)

Un screw

Push up

Mounting

plate

191

10 x

26AWG

Shield

155

14.5

4 x 5

Note: drawing dimensions are in mm

Summary of content (4 pages)

PAGE 1
® Invexs 190 readers Mifare DESfire dual technology mullion readers Install Manual GENERAL The Invexs 190 reader series is capable of reading (simultaneously) Mifare and DESFire credentials due to its dual reader technology. The Invexs 190 is designed to be used on door pillars (mullion) and suitable for outside and inside use. A model with keypad is also available. The Invexs output must be set to RS485 protocol (encrypted).
PAGE 2
Invexs 190 readers CONNECTIONS Invexs is not hot-swappable, so when making or changing connections, power must be switched Off.
PAGE 3
Invexs 190 readers LED INDICATORS FRONT At the front a three colour LED is positioned at the middle of the Invexs Depending of the used configuration the function of these LEDs can differ: • Green LED: Card is been authorised (UL led) Card is not authorised (NA led), controller is stand-by • Red LED: • Blue LED: Blinks fast: No configuration is availabele at this Invexs (present Configuration card or load Configuration first). Continuously ON: Determined by configuration: E.g. Reader stand-by.
PAGE 4
Invexs 190 readers FCC and IC CERTIFICATIONS This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.